08:55 - Starting task "Configure modules"
08:55 - Setting L0 thresholds to 15.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5
08:55 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190426/config_2019-04-26_08-55-30.NMC.xml
08:55 - Switching off high voltages in configuration
08:55 - Successfully configured 61 module(s)
08:55 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
08:55 - Found 0 PPS errors.
08:55 - Finished task "Configure modules"
08:55 - Starting task "Switch HVPA voltage state"
08:55 - Setting HVPA current limit to 12489.75 uA
08:56 - Setting HVPA ramp speed to 35 V/s
08:56 - Switching HVPA to state Nominal
08:56 - Setting HVPA current limits...
08:56 - Finished task "Switch HVPA voltage state"
08:57 - High voltage locked channels will be checked every 30 s
08:57 - Status: TibState.PpsStopped
08:57 - Alarms: AlarmVector.ReadError
08:57 - Connection status: False
08:57 - External delays: Local=0.000 ns, Calibration=55.000 ns, Sphe=150.000 ns
08:57 - Trigger mask: 0x44 = TriggerMask.SlowControl|Calibration
08:57 - Input mask: 0x0
08:57 - Disable BUSY: False
08:57 - Extra BUSY Delay: 0.0
08:57 - Temperature: 41.19
08:57 - Checking for high voltage locked pixels...
08:58 - Starting task "Check high voltages"
08:58 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
08:58 - Checking for high voltage locked pixels...
08:58 - Actual voltage is between 945.50 V and 1167.54 V.
08:58 - Low voltages range between 100.00 V and 100.00 V. 
08:58 - Reference voltages range between 945.26 V and 1167.15 V. 
08:58 - Maximum difference between expected and actual voltages is 0.76 V
08:58 - Checking for high voltage locked pixels...
08:58 - Maximum of current limits is 5647.07 uA
08:58 - Checking status of HVPA module in 61 drawer(s)...
08:58 - Checking status of HVPA channels in 61 drawer(s)...
08:58 - HV is stabilized in all channels.
08:58 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
08:59 - Done
08:59 - Finished task "Check high voltages"
08:59 - Checking for high voltage locked pixels...
08:59 - Starting NMC
08:59 - Clearing PPS error counters
08:59 - Configuring UCTS
08:59 - Configuring TIB...
08:59 - Setting TIB forced mode to False
08:59 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
08:59 - Status: TibState.PpsStopped
08:59 - Alarms: AlarmVector.ReadError
08:59 - Connection status: False
08:59 - Entering set_external_delay
08:59 - Setting ExternalDelayLocal to 0.000 ns
08:59 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
08:59 - Entering set_external_delay
08:59 - Setting ExternalDelayCalibration to 55.000 ns
08:59 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
08:59 - Entering set_external_delay
08:59 - Setting ExternalDelaySphe to 150.000 ns
08:59 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
08:59 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
08:59 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
08:59 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
08:59 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
08:59 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
08:59 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
08:59 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
08:59 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
08:59 - Status: TibState.PpsStopped
08:59 - Alarms: AlarmVector.ReadError
08:59 - Connection status: False
08:59 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
08:59 - Writing 5000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
08:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
08:59 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
08:59 - Writing 5000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
08:59 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
08:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
08:59 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
08:59 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
08:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
08:59 - Connecting TIB to camera server at 10.10.4.12:222
08:59 - Starting TIB...
08:59 - Status: TibState.PpsStopped
08:59 - Alarms: AlarmVector.ReadError
08:59 - Connection status: False
08:59 - Resetting run
08:59 - Wait for UCTS external trigger before enabling trigger...
08:59 - Status: TibState.Standby
08:59 - Alarms: AlarmVector.NoAlarm
08:59 - Connection status: False
08:59 - Status: TibState.Standby
08:59 - Alarms: AlarmVector.NoAlarm
08:59 - Connection status: False
08:59 - Status: TibState.Armed
08:59 - Alarms: AlarmVector.NoAlarm
08:59 - Connection status: True
08:59 - Checking for high voltage locked pixels...
08:59 - Starting TIB triggers...
08:59 - Enabling trigger
08:59 - Status: TibState.Running
08:59 - Alarms: AlarmVector.NoAlarm
08:59 - Connection status: True
08:59 - Configuring calibration box...
08:59 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=110 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
09:00 - Starting flashes...
09:00 - Checking for high voltage locked pixels...
09:00 - Stopping flashes...
09:00 - Checking for high voltage locked pixels...