16:11 - ECC is in state EccState.Ready with status EccStatus.NoError
16:11 - Average temperature: 20.7 deg C
16:11 - Air temperature (T1-T6 and T9-T10): 20.7, 18.9, 18.9, 20.5, 19.8, 22.0, 16.3, 15.9 deg C
16:11 - Air differential pressure: 0.2 Pa
16:11 - Water temperature (T11-T12): 15.2, 14.5 deg C
16:11 - Back doors are open.
16:11 - Shutter status: 1 (error 0)
16:11 - Light sensors: [0.01, 0.01, 0.0, 6.09] V
16:11 - Humidity: 44.2 %. Water pressure: [2.28, 1.78] bar.
16:11 - Fan speeds: [0.0, 0.0, 2280.0, 2400.0, 0.0, 0.0] rpm
16:11 - 24 V power supply no. 1 is enabled with a current of 58.800 A.
16:11 - Starting task "Check high voltages"
16:11 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:11 - Stopping NMC
16:11 - Found 0 PPS errors.
16:11 - Actual voltage is between 945.50 V and 1167.54 V.
16:11 - Low voltages range between 100.00 V and 100.00 V. 
16:11 - Stopping flashes...
16:11 - Starting NMC
16:11 - Clearing PPS error counters
16:11 - Reference voltages range between 945.26 V and 1167.15 V. 
16:11 - Maximum difference between expected and actual voltages is 0.71 V
16:11 - Maximum of current limits is 5647.07 uA
16:11 - Checking status of HVPA module in 61 drawer(s)...
16:11 - Checking status of HVPA channels in 61 drawer(s)...
16:12 - HV is stabilized in all channels.
16:12 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:12 - Done
16:12 - Finished task "Check high voltages"
16:12 - Configuring UCTS
16:12 - Configuring TIB...
16:12 - Setting TIB forced mode to False
16:12 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:12 - Status: TibState.PpsStopped
16:12 - Alarms: AlarmVector.ReadError
16:12 - Connection status: False
16:12 - Entering set_external_delay
16:12 - Setting ExternalDelayLocal to 0.000 ns
16:12 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:12 - Entering set_external_delay
16:12 - Setting ExternalDelayCalibration to 55.000 ns
16:12 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:12 - Entering set_external_delay
16:12 - Setting ExternalDelaySphe to 150.000 ns
16:12 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:12 - Setting TIB trigger mode to 0x58 = TriggerMask.SlowControl|Software|SPhE
16:12 - Writing 88 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:12 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:12 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:12 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:12 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:12 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:12 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:12 - Status: TibState.PpsStopped
16:12 - Alarms: AlarmVector.ReadError
16:12 - Connection status: False
16:12 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:12 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:12 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:12 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:12 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:12 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:12 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:12 - Connecting TIB to camera server at 10.10.4.12:222
16:12 - Starting TIB...
16:12 - Status: TibState.PpsStopped
16:12 - Alarms: AlarmVector.ReadError
16:12 - Connection status: False
16:12 - Resetting run
16:12 - Wait for UCTS external trigger before enabling trigger...
16:12 - Status: TibState.Standby
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Status: TibState.Standby
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Status: TibState.Armed
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: True
16:13 - Starting TIB triggers...
16:13 - Enabling trigger
16:13 - Status: TibState.Running
16:13 - Alarms: AlarmVector.NoAlarm
16:13 - Connection status: True
2019-04-23 16:14:27,191 Configuring calibration box with leds=0x3b8 voltage=10.00 frequency=1000/1 central_current=0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
2019-04-23 16:14:27,192 Calling method NectarCAM.CalibrationBox.Configure in object NectarCAM.CalibrationBox
2019-04-23 16:14:27,274 Moving white target to position 0: module 79
79 <class 'int'>
2019-04-23 16:14:27,283 Module 79 has coordinates (X=-343, Y=198) in camera system
2019-04-23 16:14:27,284 Module 79 has coordinates (X=1183, Y=1138) in white target system
2019-04-23 16:14:27,284 Moving white target to position (Xtarget=1183 mm, Ytarget=1138 mm)
2019-04-23 16:14:27,284 Selecting XY table position: 118.37, 113.84
2019-04-23 16:14:27,289 Moving to next XY table position
2019-04-23 16:14:27,799 XY table IS busy
2019-04-23 16:14:27,799 Waiting for XY table to be idle...
2019-04-23 16:14:28,180 XY table busy state changed to: True
2019-04-23 16:14:28,181 XY table parking state changed to: False
2019-04-23 16:14:49,188 XY table busy state changed to: False
2019-04-23 16:14:49,190 XY table is NOT busy
2019-04-23 16:14:49,194 Current position: 118.37, 81.79
2019-04-23 16:14:52,197 Starting SPE flasher
2019-04-23 16:14:52,197 Starting flashes...
2019-04-23 16:14:52,198 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:15:53,316 Stopping SPE flasher
2019-04-23 16:15:53,317 Stopping flashes...
2019-04-23 16:15:53,317 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:15:54,367 Moving white target to position 1: module 81
81 <class 'int'>
2019-04-23 16:15:54,376 Module 81 has coordinates (X=-343, Y=-66) in camera system
2019-04-23 16:15:54,376 Module 81 has coordinates (X=1183, Y=873) in white target system
2019-04-23 16:15:54,376 Moving white target to position (Xtarget=1183 mm, Ytarget=873 mm)
2019-04-23 16:15:54,376 Selecting XY table position: 118.37, 87.39
2019-04-23 16:15:54,380 Moving to next XY table position
2019-04-23 16:15:54,886 XY table IS busy
2019-04-23 16:15:54,886 Waiting for XY table to be idle...
2019-04-23 16:15:54,888 XY table IS busy
2019-04-23 16:15:54,892 Current position: 118.37, 81.79
2019-04-23 16:15:55,196 XY table busy state changed to: True
2019-04-23 16:15:57,895 Starting SPE flasher
2019-04-23 16:15:57,895 Starting flashes...
2019-04-23 16:15:57,895 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:16:12,197 XY table busy state changed to: False
2019-04-23 16:16:59,001 Stopping SPE flasher
2019-04-23 16:16:59,001 Stopping flashes...
2019-04-23 16:16:59,001 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:17:00,052 Triggering TIB by slow control
2019-04-23 16:17:00,052 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:17:00,055 Moving white target to position 2: module 83
83 <class 'int'>
2019-04-23 16:17:00,064 Module 83 has coordinates (X=-343, Y=-330) in camera system
2019-04-23 16:17:00,064 Module 83 has coordinates (X=1183, Y=609) in white target system
2019-04-23 16:17:00,064 Moving white target to position (Xtarget=1183 mm, Ytarget=609 mm)
2019-04-23 16:17:00,064 Selecting XY table position: 118.37, 60.93
2019-04-23 16:17:00,068 Moving to next XY table position
2019-04-23 16:17:00,573 XY table IS busy
2019-04-23 16:17:00,573 Waiting for XY table to be idle...
2019-04-23 16:17:00,575 XY table IS busy
2019-04-23 16:17:00,579 Current position: 118.37, 55.34
2019-04-23 16:17:01,201 XY table busy state changed to: True
2019-04-23 16:17:03,582 Starting SPE flasher
2019-04-23 16:17:03,583 Starting flashes...
2019-04-23 16:17:03,583 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:17:18,205 XY table busy state changed to: False
2019-04-23 16:18:04,693 Stopping SPE flasher
2019-04-23 16:18:04,693 Stopping flashes...
2019-04-23 16:18:04,693 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:18:05,744 Triggering TIB by slow control
2019-04-23 16:18:05,745 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:18:05,749 Moving white target to position 3: module 118
118 <class 'int'>
2019-04-23 16:18:05,758 Module 118 has coordinates (X=-114, Y=-463) in camera system
2019-04-23 16:18:05,758 Module 118 has coordinates (X=954, Y=476) in white target system
2019-04-23 16:18:05,758 Moving white target to position (Xtarget=954 mm, Ytarget=476 mm)
2019-04-23 16:18:05,758 Selecting XY table position: 95.46, 47.70
2019-04-23 16:18:05,763 Moving to next XY table position
2019-04-23 16:18:06,211 XY table busy state changed to: True
2019-04-23 16:18:06,268 XY table IS busy
2019-04-23 16:18:06,268 Waiting for XY table to be idle...
2019-04-23 16:18:27,214 XY table busy state changed to: False
2019-04-23 16:18:27,216 XY table is NOT busy
2019-04-23 16:18:27,220 Current position: 95.45, 15.65
2019-04-23 16:18:30,223 Starting SPE flasher
2019-04-23 16:18:30,223 Starting flashes...
2019-04-23 16:18:30,223 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:19:31,334 Stopping SPE flasher
2019-04-23 16:19:31,334 Stopping flashes...
2019-04-23 16:19:31,334 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:19:32,385 Triggering TIB by slow control
2019-04-23 16:19:32,385 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:19:32,388 Moving white target to position 4: module 116
116 <class 'int'>
2019-04-23 16:19:32,397 Module 116 has coordinates (X=-114, Y=-198) in camera system
2019-04-23 16:19:32,397 Module 116 has coordinates (X=954, Y=741) in white target system
2019-04-23 16:19:32,397 Moving white target to position (Xtarget=954 mm, Ytarget=741 mm)
2019-04-23 16:19:32,397 Selecting XY table position: 95.46, 74.16
2019-04-23 16:19:32,402 Moving to next XY table position
2019-04-23 16:19:32,906 XY table IS busy
2019-04-23 16:19:32,906 Waiting for XY table to be idle...
2019-04-23 16:19:32,908 XY table IS busy
2019-04-23 16:19:32,912 Current position: 95.45, 15.65
2019-04-23 16:19:33,221 XY table busy state changed to: True
2019-04-23 16:19:35,916 Starting SPE flasher
2019-04-23 16:19:35,916 Starting flashes...
2019-04-23 16:19:35,916 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:19:50,224 XY table busy state changed to: False
2019-04-23 16:20:37,026 Stopping SPE flasher
2019-04-23 16:20:37,027 Stopping flashes...
2019-04-23 16:20:37,027 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:20:38,077 Triggering TIB by slow control
2019-04-23 16:20:38,077 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:20:38,081 Moving white target to position 5: module 114
114 <class 'int'>
2019-04-23 16:20:38,090 Module 114 has coordinates (X=-114, Y=66) in camera system
2019-04-23 16:20:38,090 Module 114 has coordinates (X=954, Y=1006) in white target system
2019-04-23 16:20:38,091 Moving white target to position (Xtarget=954 mm, Ytarget=1006 mm)
2019-04-23 16:20:38,091 Selecting XY table position: 95.46, 100.61
2019-04-23 16:20:38,095 Moving to next XY table position
2019-04-23 16:20:38,600 XY table IS busy
2019-04-23 16:20:38,600 Waiting for XY table to be idle...
2019-04-23 16:20:38,602 XY table IS busy
2019-04-23 16:20:38,606 Current position: 95.46, 42.09
2019-04-23 16:20:39,228 XY table busy state changed to: True
2019-04-23 16:20:41,608 Starting SPE flasher
2019-04-23 16:20:41,608 Starting flashes...
2019-04-23 16:20:41,608 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:20:56,232 XY table busy state changed to: False
2019-04-23 16:21:42,718 Stopping SPE flasher
2019-04-23 16:21:42,719 Stopping flashes...
2019-04-23 16:21:42,719 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:21:43,770 Triggering TIB by slow control
2019-04-23 16:21:43,770 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
112 <class 'int'>
2019-04-23 16:21:43,774 Moving white target to position 6: module 112
2019-04-23 16:21:43,783 Module 112 has coordinates (X=-114, Y=330) in camera system
2019-04-23 16:21:43,784 Module 112 has coordinates (X=954, Y=1270) in white target system
2019-04-23 16:21:43,784 Moving white target to position (Xtarget=954 mm, Ytarget=1270 mm)
2019-04-23 16:21:43,784 Selecting XY table position: 95.46, 127.07
2019-04-23 16:21:43,788 Moving to next XY table position
2019-04-23 16:21:44,237 XY table busy state changed to: True
2019-04-23 16:21:44,293 XY table IS busy
2019-04-23 16:21:44,293 Waiting for XY table to be idle...
2019-04-23 16:22:02,252 XY table busy state changed to: False
2019-04-23 16:22:02,255 XY table is NOT busy
2019-04-23 16:22:02,260 Current position: 95.46, 81.98
2019-04-23 16:22:05,263 Starting SPE flasher
2019-04-23 16:22:05,263 Starting flashes...
2019-04-23 16:22:05,263 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:23:06,373 Stopping SPE flasher
2019-04-23 16:23:06,373 Stopping flashes...
2019-04-23 16:23:06,373 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:23:07,423 Triggering TIB by slow control
2019-04-23 16:23:07,424 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:23:07,427 Moving white target to position 7: module 146
146 <class 'int'>
2019-04-23 16:23:07,435 Module 146 has coordinates (X=114, Y=463) in camera system
2019-04-23 16:23:07,436 Module 146 has coordinates (X=725, Y=1403) in white target system
2019-04-23 16:23:07,436 Moving white target to position (Xtarget=725 mm, Ytarget=1403 mm)
2019-04-23 16:23:07,436 Selecting XY table position: 72.54, 140.30
2019-04-23 16:23:07,440 Moving to next XY table position
2019-04-23 16:23:07,945 XY table IS busy
2019-04-23 16:23:07,945 Waiting for XY table to be idle...
2019-04-23 16:23:07,947 XY table IS busy
2019-04-23 16:23:07,951 Current position: 95.46, 81.98
2019-04-23 16:23:08,253 XY table busy state changed to: True
2019-04-23 16:23:10,952 Starting SPE flasher
2019-04-23 16:23:10,952 Starting flashes...
2019-04-23 16:23:10,952 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:23:28,258 XY table busy state changed to: False
2019-04-23 16:24:12,061 Stopping SPE flasher
2019-04-23 16:24:12,061 Stopping flashes...
2019-04-23 16:24:12,061 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:24:13,111 Triggering TIB by slow control
2019-04-23 16:24:13,111 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:24:13,114 Moving white target to position 8: module 148
148 <class 'int'>
2019-04-23 16:24:13,123 Module 148 has coordinates (X=114, Y=198) in camera system
2019-04-23 16:24:13,124 Module 148 has coordinates (X=725, Y=1138) in white target system
2019-04-23 16:24:13,124 Moving white target to position (Xtarget=725 mm, Ytarget=1138 mm)
2019-04-23 16:24:13,124 Selecting XY table position: 72.54, 113.84
2019-04-23 16:24:13,128 Moving to next XY table position
2019-04-23 16:24:13,633 XY table IS busy
2019-04-23 16:24:13,633 Waiting for XY table to be idle...
2019-04-23 16:24:13,635 XY table IS busy
2019-04-23 16:24:13,639 Current position: 72.54, 93.94
2019-04-23 16:24:14,267 XY table busy state changed to: True
2019-04-23 16:24:16,641 Starting SPE flasher
2019-04-23 16:24:16,641 Starting flashes...
2019-04-23 16:24:16,641 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:24:31,267 XY table busy state changed to: False
2019-04-23 16:25:17,752 Stopping SPE flasher
2019-04-23 16:25:17,752 Stopping flashes...
2019-04-23 16:25:17,752 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:25:18,803 Triggering TIB by slow control
2019-04-23 16:25:18,803 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:25:18,806 Moving white target to position 9: module 150
150 <class 'int'>
2019-04-23 16:25:18,815 Module 150 has coordinates (X=114, Y=-66) in camera system
2019-04-23 16:25:18,815 Module 150 has coordinates (X=725, Y=873) in white target system
2019-04-23 16:25:18,815 Moving white target to position (Xtarget=725 mm, Ytarget=873 mm)
2019-04-23 16:25:18,815 Selecting XY table position: 72.54, 87.39
2019-04-23 16:25:18,820 Moving to next XY table position
2019-04-23 16:25:19,273 XY table busy state changed to: True
2019-04-23 16:25:19,326 XY table IS busy
2019-04-23 16:25:19,326 Waiting for XY table to be idle...
2019-04-23 16:25:37,277 XY table busy state changed to: False
2019-04-23 16:25:37,280 XY table is NOT busy
2019-04-23 16:25:37,284 Current position: 72.54, 41.06
2019-04-23 16:25:40,287 Starting SPE flasher
2019-04-23 16:25:40,287 Starting flashes...
2019-04-23 16:25:40,287 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:26:41,392 Stopping SPE flasher
2019-04-23 16:26:41,392 Stopping flashes...
2019-04-23 16:26:41,392 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:26:42,443 Triggering TIB by slow control
2019-04-23 16:26:42,443 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:26:42,446 Moving white target to position 10: module 152
152 <class 'int'>
2019-04-23 16:26:42,455 Module 152 has coordinates (X=114, Y=-330) in camera system
2019-04-23 16:26:42,456 Module 152 has coordinates (X=725, Y=609) in white target system
2019-04-23 16:26:42,456 Moving white target to position (Xtarget=725 mm, Ytarget=609 mm)
2019-04-23 16:26:42,456 Selecting XY table position: 72.54, 60.93
2019-04-23 16:26:42,460 Moving to next XY table position
2019-04-23 16:26:42,965 XY table IS busy
2019-04-23 16:26:42,965 Waiting for XY table to be idle...
2019-04-23 16:26:42,967 XY table IS busy
2019-04-23 16:26:42,971 Current position: 72.54, 41.06
2019-04-23 16:26:43,284 XY table busy state changed to: True
2019-04-23 16:26:45,973 Starting SPE flasher
2019-04-23 16:26:45,973 Starting flashes...
2019-04-23 16:26:45,973 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:27:00,284 XY table busy state changed to: False
2019-04-23 16:27:47,084 Stopping SPE flasher
2019-04-23 16:27:47,084 Stopping flashes...
2019-04-23 16:27:47,084 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:27:48,136 Triggering TIB by slow control
2019-04-23 16:27:48,136 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:27:48,141 Moving white target to position 11: module 185
185 <class 'int'>
2019-04-23 16:27:48,150 Module 185 has coordinates (X=343, Y=-198) in camera system
2019-04-23 16:27:48,150 Module 185 has coordinates (X=496, Y=741) in white target system
2019-04-23 16:27:48,151 Moving white target to position (Xtarget=496 mm, Ytarget=741 mm)
2019-04-23 16:27:48,151 Selecting XY table position: 49.63, 74.16
2019-04-23 16:27:48,155 Moving to next XY table position
2019-04-23 16:27:48,660 XY table IS busy
2019-04-23 16:27:48,661 Waiting for XY table to be idle...
2019-04-23 16:27:48,663 XY table IS busy
2019-04-23 16:27:48,668 Current position: 72.54, 14.60
2019-04-23 16:27:49,290 XY table busy state changed to: True
2019-04-23 16:27:51,671 Starting SPE flasher
2019-04-23 16:27:51,671 Starting flashes...
2019-04-23 16:27:51,671 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:28:09,292 XY table busy state changed to: False
2019-04-23 16:28:52,780 Stopping SPE flasher
2019-04-23 16:28:52,780 Stopping flashes...
2019-04-23 16:28:52,781 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:28:53,832 Triggering TIB by slow control
2019-04-23 16:28:53,832 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:28:53,835 Moving white target to position 12: module 183
183 <class 'int'>
2019-04-23 16:28:53,844 Module 183 has coordinates (X=343, Y=66) in camera system
2019-04-23 16:28:53,845 Module 183 has coordinates (X=496, Y=1006) in white target system
2019-04-23 16:28:53,845 Moving white target to position (Xtarget=496 mm, Ytarget=1006 mm)
2019-04-23 16:28:53,845 Selecting XY table position: 49.63, 100.61
2019-04-23 16:28:53,850 Moving to next XY table position
2019-04-23 16:28:54,294 XY table busy state changed to: True
2019-04-23 16:28:54,355 XY table IS busy
2019-04-23 16:28:54,355 Waiting for XY table to be idle...
2019-04-23 16:29:12,297 XY table busy state changed to: False
2019-04-23 16:29:12,300 XY table is NOT busy
2019-04-23 16:29:12,304 Current position: 49.63, 54.27
2019-04-23 16:29:15,305 Starting SPE flasher
2019-04-23 16:29:15,305 Starting flashes...
2019-04-23 16:29:15,305 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:30:16,415 Stopping SPE flasher
2019-04-23 16:30:16,415 Stopping flashes...
2019-04-23 16:30:16,415 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:30:17,466 Triggering TIB by slow control
2019-04-23 16:30:17,466 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:30:17,470 Moving white target to position 13: module 181
181 <class 'int'>
2019-04-23 16:30:17,479 Module 181 has coordinates (X=343, Y=330) in camera system
2019-04-23 16:30:17,480 Module 181 has coordinates (X=496, Y=1270) in white target system
2019-04-23 16:30:17,480 Moving white target to position (Xtarget=496 mm, Ytarget=1270 mm)
2019-04-23 16:30:17,480 Selecting XY table position: 49.63, 127.07
2019-04-23 16:30:17,484 Moving to next XY table position
2019-04-23 16:30:17,989 XY table IS busy
2019-04-23 16:30:17,989 Waiting for XY table to be idle...
2019-04-23 16:30:17,991 XY table IS busy
2019-04-23 16:30:17,995 Current position: 49.63, 54.27
2019-04-23 16:30:18,307 XY table busy state changed to: True
2019-04-23 16:30:20,998 Starting SPE flasher
2019-04-23 16:30:20,998 Starting flashes...
2019-04-23 16:30:20,998 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-23 16:30:35,308 XY table busy state changed to: False
2019-04-23 16:31:22,108 Stopping SPE flasher
2019-04-23 16:31:22,108 Stopping flashes...
2019-04-23 16:31:22,108 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-23 16:31:23,159 Triggering TIB by slow control
2019-04-23 16:31:23,159 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-23 16:31:23,163 Moving to parking position
2019-04-23 16:31:23,165 Waiting for parked position...
2019-04-23 16:31:24,315 XY table busy state changed to: True
2019-04-23 16:31:52,317 XY table busy state changed to: False
2019-04-23 16:31:52,317 XY table parking state changed to: True
2019-04-23 16:31:52,319 XY table IS parked
16:34 - Stopping TIB...
16:34 - Status: TibState.Running
16:34 - Alarms: AlarmVector.ReadError
16:34 - Connection status: True
16:34 - Disabling trigger
16:34 - Disabling PPS
16:34 - Status: TibState.PpsStopped
16:34 - Alarms: AlarmVector.ReadError
16:34 - Connection status: True
16:34 - Closing TIB connection to camera server
16:34 - Status: TibState.PpsStopped
16:34 - Alarms: AlarmVector.ReadError
16:34 - Connection status: False
16:34 - Run duration: 0:21:33
16:34 - Local camera triggers: 0
16:34 - Slow control triggers: 13
16:34 - Single photo-electron triggers: 855515
16:34 - Calibration triggers: 0
16:34 - Software triggers from UCTS: 0
16:34 - Pedestal triggers: 0
16:34 - Collected input triggers: 855528
16:34 - Busy triggers: 0
16:34 - Camera event triggers sent to clusters: 855528