10:11 - ECC is in state EccState.Ready with status EccStatus.NoError
10:11 - Average temperature: 21.1 deg C
10:11 - Air temperature (T1-T6 and T9-T10): 21.1, 19.6, 19.3, 20.8, 20.5, 22.3, 16.8, 16.4 deg C
10:11 - Air differential pressure: 0.2 Pa
10:11 - Water temperature (T11-T12): 15.5, 14.7 deg C
10:11 - Back doors are closed.
10:11 - Shutter status: 1 (error 0)
10:11 - Light sensors: [0.61, 1.01, 1.4, 6.02] V
10:11 - Humidity: 35.1 %. Water pressure: [2.28, 1.76] bar.
10:11 - Fan speeds: [0.0, 0.0, 2400.0, 2280.0, 0.0, 0.0] rpm
10:11 - 24 V power supply no. 1 is enabled with a current of 57.700 A.
10:11 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
10:11 - Found 0 PPS errors.
10:11 - Starting task "Switch HVPA voltage state"
10:11 - Setting HVPA current limit to 12489.75 uA
10:12 - Setting HVPA ramp speed to 35 V/s
10:12 - Switching HVPA to state Nominal
10:12 - Setting HVPA current limits...
10:12 - Finished task "Switch HVPA voltage state"
10:12 - High voltage locked channels will be checked every 30 s
10:13 - Checking for high voltage locked pixels...
10:13 - Module 83 has 1 pixel(s) locked (HVPA status of 0x77)!
10:13 - Module 111 has 1 pixel(s) locked (HVPA status of 0x7d)!
10:13 - Unlocking 2 channel(s)...
10:13 - Resetting HVPA channel 3 of drawer 83...
10:13 - Resetting HVPA channel 1 of drawer 111...
10:13 - Checking for high voltage locked pixels...
10:14 - Checking for high voltage locked pixels...
10:14 - Checking for high voltage locked pixels...
10:15 - Checking for high voltage locked pixels...
10:15 - Starting task "Check high voltages"
10:15 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:15 - Actual voltage is between 945.50 V and 1167.54 V.
10:15 - Low voltages range between 100.00 V and 100.00 V. 
10:15 - Reference voltages range between 945.26 V and 1167.15 V. 
10:15 - Checking for high voltage locked pixels...
10:15 - Maximum difference between expected and actual voltages is 0.71 V
10:16 - Maximum of current limits is 5647.07 uA
10:16 - Checking status of HVPA module in 61 drawer(s)...
10:16 - Checking status of HVPA channels in 61 drawer(s)...
10:16 - HV is stabilized in all channels.
10:16 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
10:16 - Done
10:16 - Finished task "Check high voltages"
10:16 - Checking for high voltage locked pixels...
10:16 - Checking for high voltage locked pixels...
10:17 - Checking for high voltage locked pixels...
10:17 - Starting task "Set L0 trigger thresholds"
10:17 - Setting L0 thresholds to 15.0 p.e.
10:17 - Checking for high voltage locked pixels...
10:17 - Setting L0 thresholds to 15.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5
10:17 - Thresholds saved in configuration file /local/home/cta_test_bench/config/2019/20190416/config_2019-04-16_10-17-58.NMC.xml
10:17 - Finished task "Set L0 trigger thresholds"
10:18 - Checking for high voltage locked pixels...
10:18 - Checking for high voltage locked pixels...
10:18 - Configuring calibration box...
10:18 - Configuring calibration box with leds=0x1fff voltage=8.50 frequency=10000.0/1 central_current=15.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:18 - Starting flashes...
10:19 - Checking for high voltage locked pixels...
10:19 - Configuring calibration box...
10:19 - Configuring calibration box with leds=0x1fbf voltage=8.50 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:19 - Starting flashes...
10:19 - Checking for high voltage locked pixels...
10:19 - Configuring calibration box...
10:19 - Configuring calibration box with leds=0x1fbf voltage=8.50 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=False
10:19 - Starting flashes...
10:20 - Configuring calibration box...
10:20 - Configuring calibration box with leds=0x1fbf voltage=8.50 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=False
10:20 - Stopping flashes...
10:20 - Checking for high voltage locked pixels...
10:20 - Checking for high voltage locked pixels...
10:21 - Checking for high voltage locked pixels...
10:21 - Configuring calibration box...
10:21 - Configuring calibration box with leds=0x1fbf voltage=16.50 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:21 - Starting flashes...
10:21 - Checking for high voltage locked pixels...
10:21 - Configuring calibration box...
10:21 - Configuring calibration box with leds=0x1fbf voltage=12.00 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:21 - Configuring calibration box...
10:21 - Configuring calibration box with leds=0x1fbf voltage=12.00 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:21 - Starting flashes...
10:22 - Checking for high voltage locked pixels...
10:22 - Configuring calibration box...
10:22 - Configuring calibration box with leds=0x1fbf voltage=14.00 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:22 - Starting flashes...
10:22 - Checking for high voltage locked pixels...
10:23 - Configuring calibration box...
10:23 - Configuring calibration box with leds=0x1fbf voltage=13.00 frequency=10000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:23 - Starting flashes...
10:23 - Checking for high voltage locked pixels...
10:23 - Configuring calibration box...
10:23 - Configuring calibration box with leds=0x1fbf voltage=13.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:23 - Starting flashes...
10:23 - Checking for high voltage locked pixels...
10:24 - Checking for high voltage locked pixels...
10:24 - Configuring calibration box...
10:24 - Configuring calibration box with leds=0x1fbf voltage=14.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:24 - Starting flashes...
10:24 - Checking for high voltage locked pixels...
10:25 - Checking for high voltage locked pixels...
10:25 - Checking for high voltage locked pixels...
10:26 - Checking for high voltage locked pixels...
10:26 - Checking for high voltage locked pixels...
10:27 - Checking for high voltage locked pixels...
10:27 - Checking for high voltage locked pixels...
10:28 - Configuring calibration box...
10:28 - Configuring calibration box with leds=0x1fbf voltage=12.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:28 - Starting flashes...
10:28 - Checking for high voltage locked pixels...
10:28 - Checking for high voltage locked pixels...
10:29 - Configuring calibration box...
10:29 - Configuring calibration box with leds=0x1fbf voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:29 - Starting flashes...
10:29 - Checking for high voltage locked pixels...
10:29 - Checking for high voltage locked pixels...
10:30 - Configuring calibration box...
10:30 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=False
10:30 - Checking for high voltage locked pixels...
10:30 - Checking for high voltage locked pixels...
10:31 - Checking for high voltage locked pixels...
10:31 - Configuring calibration box...
10:31 - Configuring calibration box with leds=0x40 voltage=8.00 frequency=1000.0/1 central_current=15.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:31 - Starting flashes...
10:31 - Checking for high voltage locked pixels...
10:32 - Configuring calibration box...
10:32 - Configuring calibration box with leds=0x40 voltage=8.00 frequency=1000.0/1 central_current=5.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:32 - Checking for high voltage locked pixels...
10:32 - Checking for high voltage locked pixels...
10:33 - Configuring calibration box...
10:33 - Configuring calibration box with leds=0x40 voltage=8.00 frequency=1000.0/1 central_current=1.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:33 - Checking for high voltage locked pixels...
10:33 - Checking for high voltage locked pixels...
10:34 - Configuring calibration box...
10:34 - Configuring calibration box with leds=0x1fbf voltage=16.50 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=True
10:34 - Starting flashes...
10:34 - Checking for high voltage locked pixels...
10:34 - Checking for high voltage locked pixels...
10:35 - Checking for high voltage locked pixels...
10:35 - Checking for high voltage locked pixels...
10:36 - Checking for high voltage locked pixels...
10:36 - Configuring calibration box...
10:36 - Configuring calibration box with leds=0x0 voltage=16.50 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=True enabled=False
10:36 - Checking for high voltage locked pixels...
10:37 - Checking for high voltage locked pixels...
10:37 - Checking for high voltage locked pixels...
10:38 - Checking for high voltage locked pixels...
10:38 - Checking for high voltage locked pixels...
10:39 - Checking for high voltage locked pixels...
10:39 - Checking for high voltage locked pixels...
10:40 - Checking for high voltage locked pixels...
10:40 - Checking for high voltage locked pixels...
10:41 - Checking for high voltage locked pixels...
10:41 - Checking for high voltage locked pixels...
10:42 - Checking for high voltage locked pixels...
10:42 - Checking for high voltage locked pixels...
10:43 - Checking for high voltage locked pixels...
10:43 - Checking for high voltage locked pixels...
10:44 - Checking for high voltage locked pixels...
10:44 - Checking for high voltage locked pixels...
10:45 - Checking for high voltage locked pixels...
10:45 - Checking status of calibration box...
10:45 - Calibration box is configured with 0 leds at a frequency of 1000.0 Hz and a voltage of 16.50 V
10:45 - Checking for high voltage locked pixels...
10:46 - Configuring calibration box...
10:46 - Configuring calibration box with leds=0x1fbf voltage=13.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=False enabled=True
10:46 - Starting flashes...
10:46 - Checking for high voltage locked pixels...
10:46 - Configuring calibration box...
10:46 - Configuring calibration box with leds=0x1fbf voltage=14.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=False enabled=True
10:46 - Starting flashes...
10:46 - Checking for high voltage locked pixels...
10:47 - Checking for high voltage locked pixels...
10:47 - Checking for high voltage locked pixels...
10:48 - Starting task "Mask all trigger channels"
10:48 - Disabling all DTC trigger channels
10:48 - Checking for high voltage locked pixels...
10:48 - Finished task "Mask all trigger channels"
10:48 - Starting task "Set DTC trigger masks"
10:48 - Confuguring DTC trigger masks for 61 configured module(s)
10:48 - Setting DTC slot 1 trigger mask to 0x1fbe
10:48 - Setting DTC slot 5 trigger mask to 0xfffe
10:48 - Setting DTC slot 9 trigger mask to 0x03fe
10:48 - Setting DTC slot 15 trigger mask to 0xfffe
10:48 - Setting DTC slot 19 trigger mask to 0x1fbe
10:48 - Checking for high voltage locked pixels...
10:48 - Finished task "Set DTC trigger masks"
10:49 - Starting NMC
10:49 - Clearing PPS error counters
10:49 - Checking for high voltage locked pixels...
10:49 - Checking for high voltage locked pixels...
10:49 - Configuring UCTS
10:50 - Error configuring UCTS: Failed to call Configure: Bad statuses are present
10:50 - Checking for high voltage locked pixels...
10:50 - Checking for high voltage locked pixels...
10:50 - Configuring UCTS
10:50 - Error configuring UCTS: Failed to call Configure: Bad statuses are present
10:51 - Checking for high voltage locked pixels...
10:51 - Checking for high voltage locked pixels...
10:51 - Configuring UCTS
10:51 - Error configuring UCTS: Failed to call Configure: Bad statuses are present
10:51 - Configuring UCTS
10:51 - Error configuring UCTS: Failed to call Configure: Bad statuses are present
10:52 - Checking for high voltage locked pixels...
10:52 - Configuring UCTS
10:52 - Error configuring UCTS: Failed to call Configure: Bad statuses are present
10:52 - Configuring UCTS
10:52 - Error configuring UCTS: Failed to call Configure: Bad statuses are present
10:52 - Checking for high voltage locked pixels...
10:53 - Checking for high voltage locked pixels...
10:53 - Checking for high voltage locked pixels...
10:54 - Checking for high voltage locked pixels...
10:54 - Checking for high voltage locked pixels...
10:55 - Checking for high voltage locked pixels...
10:55 - Checking for high voltage locked pixels...
10:56 - Configuring UCTS
10:56 - Error configuring UCTS: Failed to call Configure: Bad statuses are present
10:56 - Checking for high voltage locked pixels...
10:56 - Checking for high voltage locked pixels...
10:57 - Checking for high voltage locked pixels...
10:57 - Checking for high voltage locked pixels...
10:57 - Configuring UCTS
10:57 - Configuring TIB...
10:57 - Setting TIB forced mode to False
10:57 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:57 - Status: TibState.RunStopped
10:57 - Alarms: AlarmVector.NoAlarm
10:57 - Connection status: False
10:57 - Disabling PPS
10:57 - Status: TibState.PpsStopped
10:57 - Alarms: AlarmVector.NoAlarm
10:57 - Connection status: False
10:57 - Entering set_external_delay
10:57 - Setting ExternalDelayLocal to 0.000 ns
10:57 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:57 - Entering set_external_delay
10:57 - Setting ExternalDelayCalibration to 55.000 ns
10:57 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:57 - Entering set_external_delay
10:57 - Setting ExternalDelaySphe to 0.000 ns
10:57 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:57 - Setting TIB trigger mode to 0x51 = TriggerMask.SlowControl|Software|Mono
10:57 - Writing 81 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:57 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:57 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:57 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:57 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:57 - Status: TibState.PpsStopped
10:57 - Alarms: AlarmVector.NoAlarm
10:57 - Connection status: False
10:57 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:57 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:57 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:57 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:57 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:57 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:57 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:58 - Checking for high voltage locked pixels...
10:58 - Connecting TIB to camera server at 10.10.4.12:222
10:58 - Starting TIB...
10:58 - Status: TibState.PpsStopped
10:58 - Alarms: AlarmVector.NoAlarm
10:58 - Connection status: False
10:58 - Resetting run
10:58 - Wait for UCTS external trigger before enabling trigger...
10:58 - Status: TibState.Standby
10:58 - Alarms: AlarmVector.NoAlarm
10:58 - Connection status: False
10:58 - Status: TibState.Standby
10:58 - Alarms: AlarmVector.NoAlarm
10:58 - Connection status: False
10:58 - Status: TibState.Armed
10:58 - Alarms: AlarmVector.NoAlarm
10:58 - Connection status: True
10:58 - Checking for high voltage locked pixels...
10:58 - Starting TIB triggers...
10:58 - Enabling trigger
10:58 - Status: TibState.Running
10:58 - Alarms: AlarmVector.NoAlarm
10:58 - Connection status: True
10:59 - Stopping TIB...
10:59 - Status: TibState.Running
10:59 - Alarms: AlarmVector.ReadError
10:59 - Connection status: True
10:59 - Disabling trigger
10:59 - Disabling PPS
10:59 - Status: TibState.PpsStopped
10:59 - Alarms: AlarmVector.ReadError
10:59 - Connection status: True
10:59 - Closing TIB connection to camera server
10:59 - Status: TibState.PpsStopped
10:59 - Alarms: AlarmVector.ReadError
10:59 - Connection status: False
10:59 - Run duration: 0:00:21
10:59 - Local camera triggers: 0
10:59 - Slow control triggers: 0
10:59 - Single photo-electron triggers: 20800
10:59 - Calibration triggers: 0
10:59 - Software triggers from UCTS: 0
10:59 - Pedestal triggers: 0
10:59 - Collected input triggers: 8068
10:59 - Busy triggers: 0
10:59 - Camera event triggers sent to clusters: 8068
10:59 - Checking for high voltage locked pixels...
10:59 - Checking for high voltage locked pixels...
10:59 - Stopping NMC
10:59 - Found 0 PPS errors.
10:59 - Starting NMC
10:59 - Clearing PPS error counters
11:00 - Checking status of calibration box...
11:00 - Calibration box is configured with 13 leds at a frequency of 1000.0 Hz and a voltage of 8.99 V
11:00 - Configuring calibration box...
11:00 - Configuring calibration box with leds=0x1fbf voltage=14.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=False enabled=True
11:00 - Starting flashes...
11:00 - Checking for high voltage locked pixels...
11:00 - Configuring UCTS
11:00 - Configuring TIB...
11:00 - Setting TIB forced mode to False
11:00 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:00 - Status: TibState.PpsStopped
11:00 - Alarms: AlarmVector.ReadError
11:00 - Connection status: False
11:00 - Entering set_external_delay
11:00 - Setting ExternalDelayLocal to 0.000 ns
11:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:00 - Entering set_external_delay
11:00 - Setting ExternalDelayCalibration to 55.000 ns
11:00 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:00 - Entering set_external_delay
11:00 - Setting ExternalDelaySphe to 0.000 ns
11:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:00 - Setting TIB trigger mode to 0x51 = TriggerMask.SlowControl|Software|Mono
11:00 - Writing 81 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:00 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:00 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:00 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:00 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:00 - Status: TibState.PpsStopped
11:00 - Alarms: AlarmVector.ReadError
11:00 - Connection status: False
11:00 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:00 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:00 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:00 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:00 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:00 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:00 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:00 - Connecting TIB to camera server at 10.10.4.12:222
11:00 - Starting TIB...
11:00 - Status: TibState.PpsStopped
11:00 - Alarms: AlarmVector.ReadError
11:00 - Connection status: False
11:00 - Resetting run
11:00 - Wait for UCTS external trigger before enabling trigger...
11:00 - Status: TibState.Standby
11:00 - Alarms: AlarmVector.NoAlarm
11:00 - Connection status: False
11:00 - Status: TibState.Standby
11:00 - Alarms: AlarmVector.NoAlarm
11:00 - Connection status: False
11:00 - Status: TibState.Armed
11:00 - Alarms: AlarmVector.NoAlarm
11:00 - Connection status: True
11:00 - Checking for high voltage locked pixels...
11:00 - Starting TIB triggers...
11:00 - Enabling trigger
11:00 - Status: TibState.Running
11:00 - Alarms: AlarmVector.NoAlarm
11:00 - Connection status: True
11:00 - Status: TibState.Running ConnectionStatus: True
11:00 - Alarms: AlarmVector.ReadError
11:00 - Temperature: 39.19
11:00 - Local camera rate: 0.0 Hz
11:00 - Stereo trigger rate: 0.0 Hz
11:00 - SPE trigger rate: 1000.0 Hz
11:00 - Calibration trigger rate: 0.0 Hz
11:00 - Software trigger rate: 0.0 Hz
11:00 - Pedestal trigger rate: 0.0 Hz
11:00 - Collected trigger rate: 1001.0 Hz
11:00 - Busy rate: 0.0 Hz
11:00 - Camera trigger rate: 1001.0 Hz
11:00 - Stopping TIB...
11:00 - Status: TibState.Running
11:00 - Alarms: AlarmVector.ReadError
11:00 - Connection status: True
11:00 - Disabling trigger
11:00 - Disabling PPS
11:01 - Status: TibState.PpsStopped
11:01 - Alarms: AlarmVector.ReadError
11:01 - Connection status: True
11:01 - Closing TIB connection to camera server
11:01 - Status: TibState.PpsStopped
11:01 - Alarms: AlarmVector.ReadError
11:01 - Connection status: False
11:01 - Run duration: 0:00:14
11:01 - Local camera triggers: 0
11:01 - Slow control triggers: 0
11:01 - Single photo-electron triggers: 13151
11:01 - Calibration triggers: 0
11:01 - Software triggers from UCTS: 0
11:01 - Pedestal triggers: 0
11:01 - Collected input triggers: 6908
11:01 - Busy triggers: 0
11:01 - Camera event triggers sent to clusters: 6908
11:01 - Checking for high voltage locked pixels...
11:01 - Checking for high voltage locked pixels...
11:02 - Checking for high voltage locked pixels...
11:02 - Checking for high voltage locked pixels...