14:35 - Starting task "Powering modules..."
14:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:35 - Finished task "Powering modules..."
14:37 - ECC is in state EccState.Ready with status EccStatus.NoError
14:37 - Average temperature: 21.2 deg C
14:37 - Air temperature (T1-T6 and T9-T10): 21.2, 21.7, 18.3, 21.6, 21.6, 21.8, 18.0, 17.4 deg C
14:37 - Air differential pressure: 0.5 Pa
14:37 - Water temperature (T11-T12): 16.4, 15.3 deg C
14:37 - Back doors are open.
14:37 - Light sensors: [0.71, 1.15, 1.61, 6.18] V
14:37 - Humidity: 44.2 %. Water pressure: [1.1, 0.84] bar.
14:37 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
14:37 - 24 V power supply no. 1 is enabled with a current of 0.000 A.
14:40 - Starting task "Configure modules"
14:40 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays.NMC.xml
14:40 - Switching off high voltages in configuration
14:40 - Successfully configured 61 module(s)
14:40 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
14:40 - Starting task "Power off channels not corresponding to a configured module"
14:40 - Powering off all but 61 DTC channel(s)
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Found 0 PPS errors.
14:40 - Finished task "Configure modules"
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
14:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
14:41 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
14:41 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
14:41 - Finished task "Power off channels not corresponding to a configured module"
14:42 - Starting task "Powering modules..."
14:42 - Executing command '/opt/cta/bin/cta_ctrl --all --power_off' on Digital Trigger Crate at 10.10.4.57
14:42 - Finished task "Powering modules..."
14:42 - Resetting NMC
14:42 - Starting task "Powering modules..."
14:42 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 1 --power_on' on Digital Trigger Crate at 10.10.4.57
14:42 - Finished task "Powering modules..."
14:47 - Starting task "Powering modules..."
14:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:47 - Finished task "Powering modules..."
14:47 - Starting task "Configure modules"
14:47 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays.NMC.xml
14:47 - Switching off high voltages in configuration
14:47 - Successfully configured 61 module(s)
14:48 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
14:48 - Found 0 PPS errors.
14:48 - Finished task "Configure modules"
14:48 - Starting task "Powering modules..."
14:48 - Executing command '/opt/cta/bin/cta_ctrl --all --power_off' on Digital Trigger Crate at 10.10.4.57
14:48 - Finished task "Powering modules..."
14:48 - Starting task "Powering modules..."
14:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:48 - Resetting NMC
14:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:48 - Finished task "Powering modules..."
14:49 - Starting task "Configure modules"
14:49 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays.NMC.xml
14:49 - Switching off high voltages in configuration
14:49 - Successfully configured 61 module(s)
14:49 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
14:49 - Found 0 PPS errors.
14:49 - Finished task "Configure modules"
14:49 - Starting task "Power off channels not corresponding to a configured module"
14:49 - Powering off all but 61 DTC channel(s)
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
14:49 - Finished task "Power off channels not corresponding to a configured module"
16:38 - Stopping flashes...
16:39 - ECC is in state EccState.Ready with status EccStatus.NoError
16:39 - Average temperature: 21.9 deg C
16:39 - Air temperature (T1-T6 and T9-T10): 21.9, 20.0, 19.2, 21.9, 21.7, 22.7, 17.8, 16.8 deg C
16:39 - Air differential pressure: 0.6 Pa
16:39 - Water temperature (T11-T12): 15.9, 14.9 deg C
16:39 - Back doors are closed.
16:39 - Light sensors: [0.93, 1.3, 1.7, 2.88] V
16:39 - Humidity: 32.6 %. Water pressure: [1.1, 0.84] bar.
16:39 - Fan speeds: [0.0, 0.0, 2400.0, 2520.0, 0.0, 0.0] rpm
16:39 - 24 V power supply no. 1 is enabled with a current of 0.000 A.
16:44 - Starting task "Configure modules"
16:44 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:44 - Switching off high voltages in configuration
16:45 - Successfully configured 61 module(s)
16:45 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
16:45 - Found 0 PPS errors.
16:45 - Finished task "Configure modules"
16:45 - Starting task "Check high voltages"
16:45 - Found 0 drawer(s) in Nominal state, 0 in Low state and 61 in Wait state
16:45 - Actual voltage is between 0.00 V and 6.10 V.
16:45 - Low voltages range between 100.00 V and 100.00 V. 
16:45 - Reference voltages range between 945.26 V and 1167.15 V. 
16:45 - Maximum difference between expected and actual voltages is 6.10 V
16:45 - Maximum of current limits is 5647.07 uA
16:45 - Checking status of HVPA module in 61 drawer(s)...
16:45 - Checking status of HVPA channels in 61 drawer(s)...
16:45 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 427 channel(s)
16:45 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:46 - Done
16:46 - Finished task "Check high voltages"
16:46 - Starting task "Switch HVPA voltage state"
16:46 - Setting HVPA current limit to 12489.75 uA
16:46 - Setting HVPA ramp speed to 500 V/s
16:46 - Switching HVPA to state Low
16:47 - Setting HVPA current limits...
16:47 - Finished task "Switch HVPA voltage state"
16:47 - Starting task "Check high voltages"
16:47 - Found 0 drawer(s) in Nominal state, 61 in Low state and 0 in Wait state
16:47 - Actual voltage is between 21.96 V and 259.25 V.
16:47 - Low voltages range between 100.00 V and 100.00 V. 
16:47 - Reference voltages range between 0.00 V and 1167.15 V. 
16:48 - Maximum difference between expected and actual voltages is 87.19 V
16:48 - Maximum of current limits is 5647.07 uA
16:48 - Checking status of HVPA module in 61 drawer(s)...
16:48 - HVPA module in drawer 80 has a status of 0x3f!
16:48 - HVPA module in drawer 83 has a status of 0x77!
16:48 - HVPA module in drawer 111 has a status of 0x7d!
16:48 - HVPA module in drawer 113 has a status of 0x77!
16:48 - HVPA module in drawer 134 has a status of 0x7b!
16:48 - HVPA module in drawer 153 has a status of 0x7e!
16:48 - Checking status of HVPA channels in 61 drawer(s)...
16:48 - HVPA channel 0 of drawer 153 has status 0x8003!
16:48 - HVPA channel 1 of drawer 111 has status 0x8003!
16:48 - HVPA channel 2 of drawer 134 has status 0x8003!
16:48 - HVPA channel 3 of drawer 83 has status 0x8003!
16:48 - HVPA channel 3 of drawer 113 has status 0x8003!
16:48 - HVPA channel 6 of drawer 80 has status 0x8003!
16:48 - HV is locked in 6 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
16:48 - Resetting 6 channel(s)...
16:48 - Resetting HVPA channel 0 of drawer 153...
16:48 - Resetting HVPA channel 1 of drawer 111...
16:48 - Resetting HVPA channel 2 of drawer 134...
16:48 - Resetting HVPA channel 3 of drawer 83...
16:48 - Resetting HVPA channel 3 of drawer 113...
16:48 - Resetting HVPA channel 6 of drawer 80...
16:48 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:48 - Done
16:48 - Finished task "Check high voltages"
16:48 - Starting task "Switch HVPA voltage state"
16:48 - Setting HVPA current limit to 12489.75 uA
16:49 - Setting HVPA ramp speed to 35 V/s
16:49 - Switching HVPA to state Nominal
16:49 - Setting HVPA current limits...
16:49 - Finished task "Switch HVPA voltage state"
16:50 - Starting task "Check high voltages"
16:50 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:50 - Actual voltage is between 6.71 V and 1167.54 V.
16:50 - Low voltages range between 100.00 V and 100.00 V. 
16:50 - Reference voltages range between 945.26 V and 1167.15 V. 
16:50 - Maximum difference between expected and actual voltages is 1072.94 V
16:50 - Maximum of current limits is 5647.07 uA
16:50 - Checking status of HVPA module in 61 drawer(s)...
16:50 - HVPA module in drawer 134 has a status of 0x7b!
16:50 - Checking status of HVPA channels in 61 drawer(s)...
16:50 - HVPA channel 2 of drawer 134 has status 0x8003!
16:50 - HV is locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
16:50 - Resetting 1 channel(s)...
16:50 - Resetting HVPA channel 2 of drawer 134...
16:51 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:51 - Done
16:51 - Finished task "Check high voltages"
16:51 - High voltage locked channels will be checked every 30 s
16:51 - Checking for high voltage locked pixels...
16:52 - Checking for high voltage locked pixels...
16:52 - Checking for high voltage locked pixels...
16:53 - Checking for high voltage locked pixels...
16:53 - Checking for high voltage locked pixels...
16:54 - Checking for high voltage locked pixels...
16:54 - Starting task "Check high voltages"
16:54 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:54 - Checking for high voltage locked pixels...
16:55 - Actual voltage is between 945.50 V and 1167.54 V.
16:55 - Low voltages range between 100.00 V and 100.00 V. 
16:55 - Reference voltages range between 945.26 V and 1167.15 V. 
16:55 - Maximum difference between expected and actual voltages is 0.71 V
16:55 - Checking for high voltage locked pixels...
16:55 - Maximum of current limits is 5647.07 uA
16:55 - Checking status of HVPA module in 61 drawer(s)...
16:55 - Checking status of HVPA channels in 61 drawer(s)...
16:55 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
16:55 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:55 - Done
16:55 - Finished task "Check high voltages"
16:55 - Checking for high voltage locked pixels...
16:56 - Checking for high voltage locked pixels...
16:56 - Checking for high voltage locked pixels...
16:57 - Checking for high voltage locked pixels...
16:57 - Checking for high voltage locked pixels...
16:58 - Checking for high voltage locked pixels...
16:58 - Checking for high voltage locked pixels...
16:59 - Checking for high voltage locked pixels...
16:59 - Stopping flashes...
16:59 - Checking for high voltage locked pixels...
17:00 - Configuring UCTS
17:00 - Configuring TIB...
17:00 - Setting TIB forced mode to False
17:00 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
17:00 - Status: TibState.PpsStopped
17:00 - Alarms: AlarmVector.ReadError
17:00 - Connection status: False
17:00 - Entering set_external_delay
17:00 - Setting ExternalDelayLocal to 0.000 ns
17:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
17:00 - Entering set_external_delay
17:00 - Setting ExternalDelayCalibration to 55.000 ns
17:00 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
17:00 - Entering set_external_delay
17:00 - Setting ExternalDelaySphe to 0.000 ns
17:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
17:00 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
17:00 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
17:00 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
17:00 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
17:00 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
17:00 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
17:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
17:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
17:00 - Status: TibState.PpsStopped
17:00 - Alarms: AlarmVector.ReadError
17:00 - Connection status: False
17:00 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
17:00 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
17:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:00 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
17:00 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
17:00 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
17:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:00 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
17:00 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
17:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:00 - Checking for high voltage locked pixels...
17:00 - Checking for high voltage locked pixels...
17:01 - Connecting TIB to camera server at 10.10.4.12:222
17:01 - Starting TIB...
17:01 - Status: TibState.PpsStopped
17:01 - Alarms: AlarmVector.ReadError
17:01 - Connection status: False
17:01 - Resetting run
17:01 - Wait for UCTS external trigger before enabling trigger...
17:01 - Status: TibState.Standby
17:01 - Alarms: AlarmVector.NoAlarm
17:01 - Connection status: False
17:01 - Status: TibState.Standby
17:01 - Alarms: AlarmVector.NoAlarm
17:01 - Connection status: False
17:01 - Status: TibState.Armed
17:01 - Alarms: AlarmVector.NoAlarm
17:01 - Connection status: True
17:01 - Checking for high voltage locked pixels...
17:01 - Starting NMC
17:01 - Clearing PPS error counters
17:01 - Starting TIB triggers...
17:01 - Enabling trigger
17:01 - Status: TibState.Running
17:01 - Alarms: AlarmVector.NoAlarm
17:01 - Connection status: True
17:01 - Checking for high voltage locked pixels...
17:02 - Checking for high voltage locked pixels...
17:02 - Stopping TIB...
17:02 - Status: TibState.Running
17:02 - Alarms: AlarmVector.ReadError
17:02 - Connection status: True
17:02 - Disabling trigger
17:02 - Disabling PPS
17:02 - Status: TibState.PpsStopped
17:02 - Alarms: AlarmVector.ReadError
17:02 - Connection status: True
17:02 - Closing TIB connection to camera server
17:02 - Status: TibState.PpsStopped
17:02 - Alarms: AlarmVector.ReadError
17:02 - Connection status: False
17:02 - Run duration: 0:01:10
17:02 - Local camera triggers: 0
17:02 - Slow control triggers: 0
17:02 - Single photo-electron triggers: 0
17:02 - Calibration triggers: 0
17:02 - Software triggers from UCTS: 0
17:02 - Pedestal triggers: 6919
17:02 - Collected input triggers: 3385
17:02 - Busy triggers: 0
17:02 - Camera event triggers sent to clusters: 3385
17:02 - Checking for high voltage locked pixels...
17:03 - Checking for high voltage locked pixels...
17:03 - Checking for high voltage locked pixels...
17:04 - Checking for high voltage locked pixels...
17:04 - Checking for high voltage locked pixels...
17:05 - Stopping NMC
17:05 - Found 0 PPS errors.
17:05 - Checking for high voltage locked pixels...
17:05 - Checking for high voltage locked pixels...
17:06 - Checking for high voltage locked pixels...
17:06 - Checking for high voltage locked pixels...
17:07 - Checking for high voltage locked pixels...
17:07 - Checking for high voltage locked pixels...
17:08 - Starting NMC
17:08 - Clearing PPS error counters
17:08 - Checking for high voltage locked pixels...
17:08 - Configuring UCTS
17:08 - Configuring TIB...
17:08 - Setting TIB forced mode to False
17:08 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
17:08 - Status: TibState.PpsStopped
17:08 - Alarms: AlarmVector.ReadError
17:08 - Connection status: False
17:08 - Entering set_external_delay
17:08 - Setting ExternalDelayLocal to 0.000 ns
17:08 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
17:08 - Entering set_external_delay
17:08 - Setting ExternalDelayCalibration to 55.000 ns
17:08 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
17:08 - Entering set_external_delay
17:08 - Setting ExternalDelaySphe to 0.000 ns
17:08 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
17:08 - Setting TIB trigger mode to 0x70 = TriggerMask.SlowControl|Pedestal|Software
17:08 - Writing 112 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
17:08 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
17:08 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
17:08 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
17:08 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
17:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
17:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
17:08 - Status: TibState.PpsStopped
17:08 - Alarms: AlarmVector.ReadError
17:08 - Connection status: False
17:08 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
17:08 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
17:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:08 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
17:08 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
17:08 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
17:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:08 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
17:08 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
17:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:08 - Checking for high voltage locked pixels...
17:09 - Connecting TIB to camera server at 10.10.4.12:222
17:09 - Starting TIB...
17:09 - Status: TibState.PpsStopped
17:09 - Alarms: AlarmVector.ReadError
17:09 - Connection status: False
17:09 - Resetting run
17:09 - Wait for UCTS external trigger before enabling trigger...
17:09 - Status: TibState.Standby
17:09 - Alarms: AlarmVector.NoAlarm
17:09 - Connection status: False
17:09 - Status: TibState.Standby
17:09 - Alarms: AlarmVector.NoAlarm
17:09 - Connection status: False
17:09 - Status: TibState.Armed
17:09 - Alarms: AlarmVector.NoAlarm
17:09 - Connection status: True
17:09 - Starting TIB triggers...
17:09 - Enabling trigger
17:09 - Status: TibState.Running
17:09 - Alarms: AlarmVector.NoAlarm
17:09 - Connection status: True
17:09 - Checking for high voltage locked pixels...
17:09 - Stopping TIB...
17:09 - Status: TibState.Running
17:09 - Alarms: AlarmVector.ReadError
17:09 - Connection status: True
17:09 - Disabling trigger
17:09 - Disabling PPS
17:09 - Status: TibState.PpsStopped
17:09 - Alarms: AlarmVector.ReadError
17:09 - Connection status: True
17:09 - Closing TIB connection to camera server
17:09 - Checking for high voltage locked pixels...
17:09 - Status: TibState.PpsStopped
17:09 - Alarms: AlarmVector.ReadError
17:09 - Connection status: False
17:09 - Run duration: 0:00:36
17:09 - Local camera triggers: 0
17:09 - Slow control triggers: 0
17:09 - Single photo-electron triggers: 0
17:09 - Calibration triggers: 0
17:09 - Software triggers from UCTS: 0
17:09 - Pedestal triggers: 3589
17:09 - Collected input triggers: 2489
17:09 - Busy triggers: 0
17:09 - Camera event triggers sent to clusters: 2489
17:10 - Checking for high voltage locked pixels...
17:10 - Checking for high voltage locked pixels...
17:11 - Stopping NMC
17:11 - Found 0 PPS errors.
17:11 - Starting task "Check high voltages"
17:11 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:11 - Checking for high voltage locked pixels...
17:11 - Actual voltage is between 945.50 V and 1166.93 V.
17:11 - Low voltages range between 100.00 V and 100.00 V. 
17:11 - Reference voltages range between 945.26 V and 1167.15 V. 
17:11 - Maximum difference between expected and actual voltages is 0.72 V
17:11 - Checking for high voltage locked pixels...
17:11 - Maximum of current limits is 5647.07 uA
17:11 - Checking status of HVPA module in 61 drawer(s)...
17:11 - Checking status of HVPA channels in 61 drawer(s)...
17:12 - HV is stabilized in all channels.
17:12 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
17:12 - Done
17:12 - Finished task "Check high voltages"
17:12 - Checking for high voltage locked pixels...
17:12 - Checking for high voltage locked pixels...
17:12 - Starting NMC
17:12 - Clearing PPS error counters
17:12 - ("NmcError: Failed to call 'NectarFrontEnd_112.Dtbp.writeRegister': status Bad statuses are present, code 0xffffffff, status NmcStatus.Failed", 4294967295)
17:13 - Configuring UCTS
17:13 - Configuring TIB...
17:13 - Setting TIB forced mode to False
17:13 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
17:13 - Status: TibState.PpsStopped
17:13 - Alarms: AlarmVector.ReadError
17:13 - Connection status: False
17:13 - Entering set_external_delay
17:13 - Setting ExternalDelayLocal to 0.000 ns
17:13 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
17:13 - Entering set_external_delay
17:13 - Setting ExternalDelayCalibration to 55.000 ns
17:13 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
17:13 - Entering set_external_delay
17:13 - Setting ExternalDelaySphe to 0.000 ns
17:13 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
17:13 - Setting TIB trigger mode to 0x70 = TriggerMask.SlowControl|Pedestal|Software
17:13 - Writing 112 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
17:13 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
17:13 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
17:13 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
17:13 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
17:13 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
17:13 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
17:13 - Status: TibState.PpsStopped
17:13 - Alarms: AlarmVector.ReadError
17:13 - Connection status: False
17:13 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
17:13 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
17:13 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:13 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
17:13 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
17:13 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
17:13 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:13 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
17:13 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
17:13 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:13 - Checking for high voltage locked pixels...
17:13 - Connecting TIB to camera server at 10.10.4.12:222
17:13 - Starting TIB...
17:13 - Status: TibState.PpsStopped
17:13 - Alarms: AlarmVector.ReadError
17:13 - Connection status: False
17:13 - Resetting run
17:13 - Wait for UCTS external trigger before enabling trigger...
17:13 - Status: TibState.Standby
17:13 - Alarms: AlarmVector.NoAlarm
17:13 - Connection status: False
17:13 - Status: TibState.Standby
17:13 - Alarms: AlarmVector.NoAlarm
17:13 - Connection status: False
17:13 - Status: TibState.Armed
17:13 - Alarms: AlarmVector.NoAlarm
17:13 - Connection status: True
17:13 - Starting TIB triggers...
17:13 - Enabling trigger
17:13 - Status: TibState.Running
17:13 - Alarms: AlarmVector.NoAlarm
17:13 - Connection status: True
17:13 - Checking for high voltage locked pixels...
17:14 - Checking for high voltage locked pixels...
17:14 - Checking for high voltage locked pixels...
17:15 - Checking for high voltage locked pixels...
17:15 - Checking for high voltage locked pixels...
17:16 - Checking for high voltage locked pixels...
17:16 - Checking for high voltage locked pixels...
17:17 - Checking for high voltage locked pixels...
17:17 - Checking for high voltage locked pixels...
17:18 - Stopping TIB...
17:18 - Status: TibState.Running
17:18 - Alarms: AlarmVector.ReadError
17:18 - Connection status: True
17:18 - Disabling trigger
17:18 - Disabling PPS
17:18 - Status: TibState.PpsStopped
17:18 - Alarms: AlarmVector.ReadError
17:18 - Connection status: True
17:18 - Closing TIB connection to camera server
17:18 - Status: TibState.PpsStopped
17:18 - Alarms: AlarmVector.ReadError
17:18 - Connection status: False
17:18 - Run duration: 0:04:35
17:18 - Local camera triggers: 0
17:18 - Slow control triggers: 0
17:18 - Single photo-electron triggers: 0
17:18 - Calibration triggers: 0
17:18 - Software triggers from UCTS: 0
17:18 - Pedestal triggers: 27433
17:18 - Collected input triggers: 25367
17:18 - Busy triggers: 0
17:18 - Camera event triggers sent to clusters: 25367
17:18 - Checking for high voltage locked pixels...
17:18 - Stopping NMC
17:18 - Found 0 PPS errors.
17:18 - Checking for high voltage locked pixels...
17:19 - Checking for high voltage locked pixels...
17:19 - Checking for high voltage locked pixels...
17:20 - Checking for high voltage locked pixels...
17:20 - Checking for high voltage locked pixels...
17:21 - Checking for high voltage locked pixels...
17:21 - Checking for high voltage locked pixels...
17:22 - Checking for high voltage locked pixels...
17:22 - Checking for high voltage locked pixels...
17:23 - Checking for high voltage locked pixels...
17:23 - Checking for high voltage locked pixels...
17:24 - Checking for high voltage locked pixels...
17:24 - Checking for high voltage locked pixels...
17:25 - Checking for high voltage locked pixels...
17:25 - Checking for high voltage locked pixels...
17:26 - Checking for high voltage locked pixels...
17:26 - Checking for high voltage locked pixels...
17:27 - Checking for high voltage locked pixels...
17:27 - Checking for high voltage locked pixels...
17:28 - Checking for high voltage locked pixels...
17:28 - Checking for high voltage locked pixels...
17:29 - Checking for high voltage locked pixels...
17:29 - Checking for high voltage locked pixels...
17:30 - Checking for high voltage locked pixels...
17:30 - Checking for high voltage locked pixels...
17:31 - Checking for high voltage locked pixels...
17:31 - Checking for high voltage locked pixels...
17:32 - Checking for high voltage locked pixels...
17:32 - Checking for high voltage locked pixels...
17:33 - Checking for high voltage locked pixels...
17:33 - Checking for high voltage locked pixels...
17:34 - Checking for high voltage locked pixels...
17:34 - Checking for high voltage locked pixels...
17:35 - Checking for high voltage locked pixels...
17:35 - Checking for high voltage locked pixels...
17:36 - Checking for high voltage locked pixels...
17:36 - Checking for high voltage locked pixels...
17:37 - Checking for high voltage locked pixels...
17:37 - Checking for high voltage locked pixels...
17:38 - Checking for high voltage locked pixels...
17:38 - Checking for high voltage locked pixels...
17:39 - Checking for high voltage locked pixels...
17:39 - Checking for high voltage locked pixels...
17:40 - Checking for high voltage locked pixels...
17:40 - Checking for high voltage locked pixels...
17:41 - Checking for high voltage locked pixels...
17:41 - Checking for high voltage locked pixels...
17:42 - Checking for high voltage locked pixels...
17:42 - Checking for high voltage locked pixels...
17:43 - Checking for high voltage locked pixels...
17:43 - Checking for high voltage locked pixels...
17:44 - Checking for high voltage locked pixels...
17:44 - Checking for high voltage locked pixels...
17:45 - Checking for high voltage locked pixels...
17:45 - Checking for high voltage locked pixels...
17:46 - Checking for high voltage locked pixels...
17:46 - Checking for high voltage locked pixels...
17:47 - Checking for high voltage locked pixels...
17:47 - Checking for high voltage locked pixels...
17:48 - Checking for high voltage locked pixels...
17:48 - Checking for high voltage locked pixels...
17:48 - Starting task "Switch HVPA voltage state"
17:48 - Setting HVPA current limit to 12489.75 uA
17:49 - Checking for high voltage locked pixels...
17:49 - Setting HVPA ramp speed to 500 V/s
17:49 - Switching HVPA to state Low
17:49 - Setting HVPA current limits...
17:49 - Checking for high voltage locked pixels...
17:50 - Finished task "Switch HVPA voltage state"
17:50 - Checking for high voltage locked pixels...
17:50 - Stopped periodic check of locked high voltages
17:50 - Starting task "Check high voltages"
17:50 - Found 0 drawer(s) in Nominal state, 61 in Low state and 0 in Wait state
17:50 - Actual voltage is between 170.19 V and 205.57 V.
17:50 - Low voltages range between 100.00 V and 100.00 V. 
17:50 - Reference voltages range between 945.26 V and 1167.15 V. 
17:51 - Maximum difference between expected and actual voltages is 92.76 V
17:51 - Maximum of current limits is 5647.07 uA
17:51 - Checking status of HVPA module in 61 drawer(s)...
17:51 - Checking status of HVPA channels in 61 drawer(s)...
17:51 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 427 channel(s)
17:51 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
17:51 - Done
17:51 - Finished task "Check high voltages"
17:51 - Starting task "Check high voltages"
17:51 - Found 0 drawer(s) in Nominal state, 61 in Low state and 0 in Wait state
17:51 - Actual voltage is between 134.81 V and 163.48 V.
17:51 - Low voltages range between 100.00 V and 100.00 V. 
17:51 - Reference voltages range between 945.26 V and 1167.15 V. 
17:52 - Maximum difference between expected and actual voltages is 54.94 V
17:52 - Maximum of current limits is 5647.07 uA
17:52 - Checking status of HVPA module in 61 drawer(s)...
17:52 - Checking status of HVPA channels in 61 drawer(s)...
17:52 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 427 channel(s)
17:52 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
17:52 - Done
17:52 - Finished task "Check high voltages"
18:03 - Starting task "Check high voltages"
18:03 - Found 0 drawer(s) in Nominal state, 61 in Low state and 0 in Wait state
18:03 - Actual voltage is between 23.79 V and 100.65 V.
18:03 - Low voltages range between 100.00 V and 100.00 V. 
18:03 - Reference voltages range between 0.00 V and 1167.15 V. 
18:03 - Maximum difference between expected and actual voltages is 78.04 V
18:03 - Maximum of current limits is 5647.07 uA
18:03 - Checking status of HVPA module in 61 drawer(s)...
18:03 - HVPA module in drawer 118 has a status of 0x77!
18:03 - Checking status of HVPA channels in 61 drawer(s)...
18:03 - HVPA channel 3 of drawer 118 has status 0x8003!
18:03 - HV is locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
18:03 - Resetting 1 channel(s)...
18:03 - Resetting HVPA channel 3 of drawer 118...
18:03 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:03 - Done
18:03 - Finished task "Switch HVPA voltage state"
18:04 - Starting task "Check high voltages"
18:04 - Found 0 drawer(s) in Nominal state, 61 in Low state and 0 in Wait state
18:04 - Actual voltage is between 99.43 V and 100.65 V.
18:04 - Low voltages range between 100.00 V and 100.00 V. 
18:04 - Reference voltages range between 945.26 V and 1167.15 V. 
18:04 - Maximum difference between expected and actual voltages is 0.65 V
18:04 - High voltage locked channels will be checked every 30 s
18:04 - Maximum of current limits is 5647.07 uA
18:04 - Checking status of HVPA module in 61 drawer(s)...
18:04 - Checking status of HVPA channels in 61 drawer(s)...
18:04 - HV is stabilized in all channels.
18:04 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:04 - Done
18:04 - Finished task "Switch HVPA voltage state"
18:05 - Starting task "Check high voltages"
18:05 - Found 0 drawer(s) in Nominal state, 61 in Low state and 0 in Wait state
18:05 - Checking for high voltage locked pixels...
18:05 - Actual voltage is between 99.43 V and 100.65 V.
18:05 - Low voltages range between 100.00 V and 100.00 V. 
18:05 - Reference voltages range between 945.26 V and 1167.15 V. 
18:05 - Maximum difference between expected and actual voltages is 0.65 V
18:05 - Maximum of current limits is 5647.07 uA
18:05 - Checking status of HVPA module in 61 drawer(s)...
18:05 - Checking status of HVPA channels in 61 drawer(s)...
18:05 - Checking for high voltage locked pixels...
18:05 - HV is stabilized in all channels.
18:05 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:05 - Done
18:05 - Finished task "Check high voltages"
18:05 - Resetting NMC
18:06 - Could not invoke the MethodCall service: BadTimeout
18:06 - Starting task "Configure modules"
18:06 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:06 - Switching off high voltages in configuration
18:06 - Checking for high voltage locked pixels...
18:06 - Could not invoke the MethodCall service: BadTimeout
18:06 - Stopped periodic check of locked high voltages
18:06 - Could not invoke the Read service: BadTimeout
18:06 - Finished task "Configure modules"
18:06 - Starting task "Configure modules"
18:06 - The following monitored items could not be created: 0
18:06 - Could not invoke the Read service: BadTimeout
18:06 - Finished task "Configure modules"
18:07 - Starting task "Switch HVPA voltage state"
18:07 - NMC does not know any module!
18:07 - Finished task "Switch HVPA voltage state"
18:10 - Could not invoke the Read service: BadTimeout
18:10 - Could not invoke the Read service: BadTimeout
18:10 - No server with URI='urn:UnifiedAutomation:UaServerCpp' has been discovered. The client could not discover a single server.
18:12 - Starting task "Configure modules"
18:12 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:12 - Switching off high voltages in configuration
18:12 - Successfully configured 61 module(s)
18:12 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
18:12 - Found 0 PPS errors.
18:12 - Finished task "Configure modules"
18:12 - Starting task "Switch HVPA voltage state"
18:12 - Setting HVPA current limit to 12489.75 uA
18:13 - Setting HVPA ramp speed to 500 V/s
18:13 - Switching HVPA to state Low
18:13 - Setting HVPA current limits...
18:13 - Finished task "Check high voltages"
18:14 - High voltage locked channels will be checked every 30 s
18:14 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
18:14 - Found 0 PPS errors.
18:14 - Checking for high voltage locked pixels...
18:14 - Starting task "Check high voltages"
18:14 - Found 0 drawer(s) in Nominal state, 61 in Low state and 0 in Wait state
18:14 - Actual voltage is between 99.43 V and 100.65 V.
18:14 - Low voltages range between 100.00 V and 100.00 V. 
18:15 - Reference voltages range between 945.26 V and 1167.15 V. 
18:15 - Maximum difference between expected and actual voltages is 0.65 V
18:15 - Checking for high voltage locked pixels...
18:15 - Maximum of current limits is 5647.07 uA
18:15 - Checking status of HVPA module in 61 drawer(s)...
18:15 - Checking status of HVPA channels in 61 drawer(s)...
18:15 - HV is stabilized in all channels.
18:15 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:15 - Done
18:15 - Finished task "Check high voltages"
18:15 - Starting task "Switch HVPA voltage state"
18:15 - Setting HVPA current limit to 12489.75 uA
18:15 - Checking for high voltage locked pixels...
18:15 - Setting HVPA ramp speed to 35 V/s
18:15 - Switching HVPA to state Nominal
18:16 - Setting HVPA current limits...
18:16 - Checking for high voltage locked pixels...
18:16 - Finished task "Switch HVPA voltage state"
18:16 - Checking for high voltage locked pixels...
18:16 - Starting task "Check high voltages"
18:17 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
18:17 - Checking for high voltage locked pixels...
18:17 - Actual voltage is between 945.50 V and 1167.54 V.
18:17 - Low voltages range between 100.00 V and 100.00 V. 
18:17 - Reference voltages range between 945.26 V and 1167.15 V. 
18:17 - Maximum difference between expected and actual voltages is 0.69 V
18:17 - Maximum of current limits is 5647.07 uA
18:17 - Checking status of HVPA module in 61 drawer(s)...
18:17 - Checking status of HVPA channels in 61 drawer(s)...
18:17 - Checking for high voltage locked pixels...
18:17 - HV is stabilized in all channels.
18:17 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:17 - Done
18:17 - Finished task "Check high voltages"
18:17 - Stopped periodic check of locked high voltages
18:18 - Starting NMC
18:18 - Clearing PPS error counters
18:18 - Configuring UCTS
18:18 - Configuring TIB...
18:18 - Setting TIB forced mode to False
18:18 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
18:18 - Status: TibState.PpsStopped
18:18 - Alarms: AlarmVector.ReadError
18:18 - Connection status: False
18:18 - Entering set_external_delay
18:18 - Setting ExternalDelayLocal to 0.000 ns
18:18 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
18:18 - Entering set_external_delay
18:18 - Setting ExternalDelayCalibration to 55.000 ns
18:18 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
18:18 - Entering set_external_delay
18:18 - Setting ExternalDelaySphe to 0.000 ns
18:18 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
18:18 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
18:18 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
18:18 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
18:18 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
18:18 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
18:18 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
18:18 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
18:18 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
18:18 - Status: TibState.PpsStopped
18:18 - Alarms: AlarmVector.ReadError
18:18 - Connection status: False
18:18 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
18:18 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
18:18 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:18 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
18:18 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
18:18 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
18:18 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:18 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
18:18 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
18:18 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:19 - Connecting TIB to camera server at 10.10.4.12:222
18:19 - Starting TIB...
18:19 - Status: TibState.PpsStopped
18:19 - Alarms: AlarmVector.ReadError
18:19 - Connection status: False
18:19 - Resetting run
18:19 - Wait for UCTS external trigger before enabling trigger...
18:19 - Status: TibState.Standby
18:19 - Alarms: AlarmVector.NoAlarm
18:19 - Connection status: False
18:19 - Status: TibState.Standby
18:19 - Alarms: AlarmVector.NoAlarm
18:19 - Connection status: False
18:19 - Status: TibState.Armed
18:19 - Alarms: AlarmVector.NoAlarm
18:19 - Connection status: True
18:19 - Starting TIB triggers...
18:19 - Enabling trigger
18:19 - Status: TibState.Running
18:19 - Alarms: AlarmVector.NoAlarm
18:19 - Connection status: True
18:20 - Configuring calibration box...
18:20 - Configuring calibration box with leds=0x1fff voltage=16.50 frequency=1000.0/1 central_current=0.0 duration=200 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
18:20 - Starting flashes...
18:21 - Stopping flashes...
18:21 - Stopping TIB...
18:21 - Status: TibState.Running
18:21 - Alarms: AlarmVector.ReadError
18:21 - Connection status: True
18:21 - Disabling trigger
18:21 - Disabling PPS
18:21 - Status: TibState.PpsStopped
18:21 - Alarms: AlarmVector.ReadError
18:21 - Connection status: True
18:21 - Closing TIB connection to camera server
18:21 - Status: TibState.PpsStopped
18:21 - Alarms: AlarmVector.ReadError
18:21 - Connection status: False
18:21 - Run duration: 0:02:29
18:21 - Local camera triggers: 0
18:21 - Slow control triggers: 0
18:21 - Single photo-electron triggers: 0
18:21 - Calibration triggers: 19966
18:21 - Software triggers from UCTS: 0
18:21 - Pedestal triggers: 14879
18:21 - Collected input triggers: 19966
18:21 - Busy triggers: 0
18:21 - Camera event triggers sent to clusters: 19966
18:22 - Stopping NMC
18:22 - Found 0 PPS errors.
18:22 - Starting task "Check high voltages"
18:22 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
18:23 - Actual voltage is between 945.50 V and 1166.93 V.
18:23 - Low voltages range between 100.00 V and 100.00 V. 
18:23 - Reference voltages range between 945.26 V and 1167.15 V. 
18:23 - Maximum difference between expected and actual voltages is 1.07 V
18:23 - Maximum of current limits is 5647.07 uA
18:23 - Checking status of HVPA module in 61 drawer(s)...
18:23 - Checking status of HVPA channels in 61 drawer(s)...
18:23 - HV is stabilized in all channels.
18:23 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
18:23 - Done
18:23 - Finished task "Check high voltages"