11:17 - ECC is in state EccState.Ready with status EccStatus.NoError
11:17 - Average temperature: 22.1 deg C
11:17 - Air temperature (T1-T6 and T9-T10): 22.1, 22.4, 18.5, 22.5, 22.4, 23.5, 18.6, 17.2 deg C
11:17 - Air differential pressure: 0.6 Pa?
11:17 - Water temperature (T11-T12): 16.2, 15.1 deg C
11:17 - Back doors are closed.
11:17 - Light sensors: [0.77, 1.21, 1.67, 6.26] V
11:17 - Humidity: 40.6 %. Water pressure: [1.1, 0.84] bar.
11:17 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
11:17 - 24 V power supply no. 1 is enabled with a current of 1484.000 A.
11:17 - Checking for high voltage locked pixels...
11:17 - Stopping NMC
11:17 - Found 0 PPS errors.
11:17 - Starting task "Check high voltages"
11:17 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:17 - Actual voltage is between 945.50 V and 1167.54 V.
11:17 - Low voltages range between 100.00 V and 100.00 V. 
11:17 - Reference voltages range between 945.26 V and 1167.15 V. 
11:17 - Checking for high voltage locked pixels...
11:17 - Maximum difference between expected and actual voltages is 0.71 V
11:17 - Maximum of current limits is 5647.07 uA
11:17 - Checking status of HVPA module in 61 drawer(s)...
11:17 - Checking status of HVPA channels in 61 drawer(s)...
11:18 - HV is stabilized in all channels.
11:18 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
11:18 - Done
11:18 - Finished task "Check high voltages"
11:18 - Checking for high voltage locked pixels...
11:18 - Starting NMC
11:18 - Clearing PPS error counters
11:18 - Configuring calibration box...
11:18 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
11:18 - Starting flashes...
11:18 - Checking for high voltage locked pixels...
11:19 - Configuring UCTS
11:19 - Configuring TIB...
11:19 - Setting TIB forced mode to False
11:19 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:19 - Status: TibState.PpsStopped
11:19 - Alarms: AlarmVector.ReadError
11:19 - Connection status: False
11:19 - Entering set_external_delay
11:19 - Setting ExternalDelayLocal to 0.000 ns
11:19 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:19 - Entering set_external_delay
11:19 - Setting ExternalDelayCalibration to 51.000 ns
11:19 - Writing 51.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:19 - Entering set_external_delay
11:19 - Setting ExternalDelaySphe to 0.000 ns
11:19 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:19 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
11:19 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:19 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:19 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:19 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:19 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:19 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:19 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:19 - Status: TibState.PpsStopped
11:19 - Alarms: AlarmVector.ReadError
11:19 - Connection status: False
11:19 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:19 - Writing 3000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:19 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:19 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:19 - Writing 3000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:19 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:19 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:19 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:19 - Writing 500.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:19 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:19 - Connecting TIB to camera server at 10.10.4.12:222
11:19 - Starting TIB...
11:19 - Status: TibState.PpsStopped
11:19 - Alarms: AlarmVector.ReadError
11:19 - Connection status: False
11:19 - Resetting run
11:19 - Wait for UCTS external trigger before enabling trigger...
11:19 - Status: TibState.Standby
11:19 - Alarms: AlarmVector.NoAlarm
11:19 - Connection status: False
11:19 - Status: TibState.Standby
11:19 - Alarms: AlarmVector.NoAlarm
11:19 - Connection status: False
11:19 - Status: TibState.Armed
11:19 - Alarms: AlarmVector.NoAlarm
11:19 - Connection status: True
11:19 - Checking for high voltage locked pixels...
11:19 - Starting TIB triggers...
11:19 - Enabling trigger
11:19 - Status: TibState.Running
11:19 - Alarms: AlarmVector.NoAlarm
11:19 - Connection status: True
11:19 - Stopping TIB...
11:19 - Status: TibState.Running
11:19 - Alarms: AlarmVector.ReadError
11:19 - Connection status: True
11:19 - Disabling trigger
11:19 - Disabling PPS
11:19 - Status: TibState.PpsStopped
11:19 - Alarms: AlarmVector.ReadError
11:19 - Connection status: True
11:19 - Closing TIB connection to camera server
11:19 - Status: TibState.PpsStopped
11:19 - Alarms: AlarmVector.ReadError
11:19 - Connection status: False
11:19 - Run duration: 0:00:17
11:19 - Local camera triggers: 0
11:19 - Slow control triggers: 0
11:19 - Single photo-electron triggers: 0
11:19 - Calibration triggers: 16325
11:19 - Software triggers from UCTS: 0
11:19 - Pedestal triggers: 0
11:19 - Collected input triggers: 10985
11:19 - Busy triggers: 0
11:19 - Camera event triggers sent to clusters: 10985