10:08 - Checking for high voltage locked pixels...
10:08 - ECC is in state EccState.Ready with status EccStatus.NoError
10:08 - Average temperature: 22.1 deg C
10:08 - Air temperature (T1-T6 and T9-T10): 22.1, 22.4, 18.5, 22.5, 22.4, 23.5, 18.6, 17.2 deg C
10:08 - Air differential pressure: 0.6 Pa?
10:08 - Water temperature (T11-T12): 16.2, 15.1 deg C
10:08 - Back doors are closed.
10:08 - Light sensors: [0.88, 1.28, 1.72, 1.87] V
10:08 - Humidity: 22.6 %. Water pressure: [1.1, 0.84] bar.
10:08 - Fan speeds: [0.0, 0.0, 2160.0, 2280.0, 0.0, 0.0] rpm
10:08 - 24 V power supply no. 1 is enabled with a current of 1330.000 A.
10:08 - Stopping NMC
10:08 - Found 0 PPS errors.
10:08 - Starting task "Check high voltages"
10:08 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:08 - Starting NMC
10:08 - Clearing PPS error counters
10:08 - Actual voltage is between 945.50 V and 1167.54 V.
10:08 - Low voltages range between 100.00 V and 100.00 V. 
10:08 - Reference voltages range between 945.26 V and 1167.15 V. 
10:08 - Checking for high voltage locked pixels...
10:08 - Maximum difference between expected and actual voltages is 0.76 V
10:09 - Maximum of current limits is 5647.07 uA
10:09 - Checking status of HVPA module in 61 drawer(s)...
10:09 - Checking status of HVPA channels in 61 drawer(s)...
10:09 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 3 channel(s)
10:09 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
10:09 - Done
10:09 - Finished task "Check high voltages"
10:09 - Checking for high voltage locked pixels...
10:09 - Checking for high voltage locked pixels...
10:10 - Checking for high voltage locked pixels...
10:10 - Checking for high voltage locked pixels...
10:11 - Checking for high voltage locked pixels...
10:11 - Checking for high voltage locked pixels...
10:12 - Configuring calibration box...
10:12 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
10:12 - Status: TibState.PpsStopped ConnectionStatus: False
10:12 - Alarms: AlarmVector.ReadError
10:12 - Temperature: 36.19
10:12 - Local camera rate: 0.0 Hz
10:12 - Stereo trigger rate: 0.0 Hz
10:12 - SPE trigger rate: 0.0 Hz
10:12 - Calibration trigger rate: 3918.0 Hz
10:12 - Software trigger rate: 0.0 Hz
10:12 - Pedestal trigger rate: 0.0 Hz
10:12 - Collected trigger rate: 0.0 Hz
10:12 - Busy rate: 0.0 Hz
10:12 - Camera trigger rate: 0.0 Hz
10:12 - Checking for high voltage locked pixels...
10:12 - Configuring UCTS
10:12 - Configuring TIB...
10:12 - Setting TIB forced mode to False
10:12 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:12 - Status: TibState.PpsStopped
10:12 - Alarms: AlarmVector.ReadError
10:12 - Connection status: False
10:12 - Entering set_external_delay
10:12 - Setting ExternalDelayLocal to 0.000 ns
10:12 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:12 - Entering set_external_delay
10:12 - Setting ExternalDelayCalibration to 40.000 ns
10:12 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:12 - Entering set_external_delay
10:12 - Setting ExternalDelaySphe to 0.000 ns
10:12 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:12 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:12 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:12 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:12 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:12 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:12 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:12 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:12 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:12 - Status: TibState.PpsStopped
10:12 - Alarms: AlarmVector.ReadError
10:12 - Connection status: False
10:12 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:12 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:12 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:12 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:12 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:12 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:12 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:12 - Checking for high voltage locked pixels...
10:12 - Connecting TIB to camera server at 10.10.4.12:222
10:12 - Starting TIB...
10:12 - Status: TibState.PpsStopped
10:12 - Alarms: AlarmVector.ReadError
10:12 - Connection status: False
10:12 - Resetting run
10:12 - Wait for UCTS external trigger before enabling trigger...
10:12 - Status: TibState.Standby
10:12 - Alarms: AlarmVector.NoAlarm
10:12 - Connection status: False
10:12 - Status: TibState.Standby
10:12 - Alarms: AlarmVector.NoAlarm
10:12 - Connection status: False
10:12 - Status: TibState.Armed
10:12 - Alarms: AlarmVector.NoAlarm
10:12 - Connection status: True
10:13 - Checking for high voltage locked pixels...
10:13 - Starting TIB triggers...
10:13 - Enabling trigger
10:13 - Status: TibState.Running
10:13 - Alarms: AlarmVector.NoAlarm
10:13 - Connection status: True
10:13 - Status: TibState.Running ConnectionStatus: True
10:13 - Alarms: AlarmVector.ReadError
10:13 - Temperature: 36.19
10:13 - Local camera rate: 0.0 Hz
10:13 - Stereo trigger rate: 0.0 Hz
10:13 - SPE trigger rate: 0.0 Hz
10:13 - Calibration trigger rate: 4020.0 Hz
10:13 - Software trigger rate: 0.0 Hz
10:13 - Pedestal trigger rate: 0.0 Hz
10:13 - Collected trigger rate: 3969.0 Hz
10:13 - Busy rate: 137.0 Hz
10:13 - Camera trigger rate: 3832.0 Hz
10:13 - Stopping TIB...
10:13 - Status: TibState.Running
10:13 - Alarms: AlarmVector.ReadError
10:13 - Connection status: True
10:13 - Disabling trigger
10:13 - Disabling PPS
10:13 - Status: TibState.PpsStopped
10:13 - Alarms: AlarmVector.ReadError
10:13 - Connection status: True
10:13 - Closing TIB connection to camera server
10:13 - Status: TibState.PpsStopped
10:13 - Alarms: AlarmVector.ReadError
10:13 - Connection status: False
10:13 - Run duration: 0:00:29
10:13 - Local camera triggers: 0
10:13 - Slow control triggers: 0
10:13 - Single photo-electron triggers: 0
10:13 - Calibration triggers: 115026
10:13 - Software triggers from UCTS: 0
10:13 - Pedestal triggers: 0
10:13 - Collected input triggers: 19387
10:13 - Busy triggers: 655
10:13 - Camera event triggers sent to clusters: 18732
10:13 - Checking for high voltage locked pixels...