14:30 - ECC is in state EccState.Ready with status EccStatus.NoError
14:30 - Average temperature: 21.5 deg C
14:30 - Air temperature (T1-T6 and T9-T10): 21.5, 21.7, 18.1, 21.8, 21.7, 22.8, 18.2, 16.9 deg C
14:30 - Air differential pressure: 0.6 Pa?
14:30 - Water temperature (T11-T12): 16.0, 14.9 deg C
14:30 - Back doors are closed.
14:30 - Light sensors: [0.95, 1.33, 1.74, 3.85] V
14:30 - Humidity: 41.9 %. Water pressure: [1.1, 0.84] bar.
14:30 - Fan speeds: [0.0, 0.0, 2400.0, 2280.0, 0.0, 0.0] rpm
14:30 - 24 V power supply no. 1 is enabled with a current of 1464.000 A.
14:30 - Starting task "Check high voltages"
14:30 - Checking for high voltage locked pixels...
14:30 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:30 - Actual voltage is between 945.50 V and 1166.93 V.
14:30 - Low voltages range between 100.00 V and 100.00 V. 
14:30 - Reference voltages range between 945.26 V and 1167.15 V. 
14:30 - Checking for high voltage locked pixels...
14:30 - Maximum difference between expected and actual voltages is 0.68 V
14:31 - Maximum of current limits is 5647.07 uA
14:31 - Checking status of HVPA module in 61 drawer(s)...
14:31 - Checking status of HVPA channels in 61 drawer(s)...
14:31 - HV is stabilized in all channels.
14:31 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays.NMC.xml
14:31 - Done
14:31 - Finished task "Check high voltages"
14:31 - Checking for high voltage locked pixels...
14:31 - Checking for high voltage locked pixels...
14:32 - Stopping NMC
14:32 - Found 0 PPS errors.
14:32 - Resetting NMC
14:32 - Starting task "Configure modules"
14:32 - Setting L0 thresholds to 30.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5
14:32 - Checking for high voltage locked pixels...
14:32 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190401/config_2019-04-01_14-32-26.NMC.xml
14:32 - Switching off high voltages in configuration
14:32 - Successfully configured 61 module(s)
14:32 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
14:32 - Found 0 PPS errors.
14:32 - Finished task "Configure modules"
14:32 - Starting task "Switch HVPA voltage state"
14:32 - Setting HVPA current limit to 12489.75 uA
14:32 - Checking for high voltage locked pixels...
14:33 - Setting HVPA ramp speed to 35 V/s
14:33 - Switching HVPA to state Nominal
14:33 - Setting HVPA current limits...
14:33 - Checking for high voltage locked pixels...
14:33 - Finished task "Switch HVPA voltage state"
14:33 - Starting task "Check high voltages"
14:33 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:33 - Actual voltage is between 945.50 V and 1166.93 V.
14:33 - Low voltages range between 100.00 V and 100.00 V. 
14:33 - Checking for high voltage locked pixels...
14:34 - Reference voltages range between 945.26 V and 1167.15 V. 
14:34 - Maximum difference between expected and actual voltages is 0.98 V
14:34 - Maximum of current limits is 5647.07 uA
14:34 - Checking status of HVPA module in 61 drawer(s)...
14:34 - Checking status of HVPA channels in 61 drawer(s)...
14:34 - HV is stabilized in all channels.
14:34 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays.NMC.xml
14:34 - Checking for high voltage locked pixels...
14:34 - Done
14:34 - Finished task "Check high voltages"
14:34 - Checking for high voltage locked pixels...
14:35 - Starting NMC
14:35 - Clearing PPS error counters
14:35 - Checking for high voltage locked pixels...
14:35 - Checking for high voltage locked pixels...
14:36 - Configuring calibration box...
14:36 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
14:36 - Checking for high voltage locked pixels...
14:36 - Starting flashes...
14:36 - Configuring UCTS
14:36 - Configuring TIB...
14:36 - Setting TIB forced mode to False
14:36 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:36 - Status: TibState.PpsStopped
14:36 - Alarms: AlarmVector.ReadError
14:36 - Connection status: False
14:36 - Entering set_external_delay
14:36 - Setting ExternalDelayLocal to 0.000 ns
14:36 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
14:36 - Entering set_external_delay
14:36 - Setting ExternalDelayCalibration to 40.000 ns
14:36 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:36 - Entering set_external_delay
14:36 - Setting ExternalDelaySphe to 0.000 ns
14:36 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:36 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
14:36 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:36 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:36 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:36 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:36 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:36 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:36 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:36 - Status: TibState.PpsStopped
14:36 - Alarms: AlarmVector.ReadError
14:36 - Connection status: False
14:36 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:36 - Writing 10 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:36 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:36 - Writing 10 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:36 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:36 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:36 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:36 - Checking for high voltage locked pixels...
14:37 - Connecting TIB to camera server at 10.10.4.12:222
14:37 - Starting TIB...
14:37 - Status: TibState.PpsStopped
14:37 - Alarms: AlarmVector.ReadError
14:37 - Connection status: False
14:37 - Resetting run
14:37 - Wait for UCTS external trigger before enabling trigger...
14:37 - Status: TibState.Standby
14:37 - Alarms: AlarmVector.NoAlarm
14:37 - Connection status: False
14:37 - Status: TibState.Standby
14:37 - Alarms: AlarmVector.NoAlarm
14:37 - Connection status: False
14:37 - Status: TibState.Armed
14:37 - Alarms: AlarmVector.NoAlarm
14:37 - Connection status: True
14:37 - Starting TIB triggers...
14:37 - Enabling trigger
14:37 - Status: TibState.Running
14:37 - Alarms: AlarmVector.NoAlarm
14:37 - Connection status: True
14:37 - Status: TibState.Running ConnectionStatus: True
14:37 - Alarms: AlarmVector.ReadError
14:37 - Temperature: 35.56
14:37 - Local camera rate: 0.0 Hz
14:37 - Stereo trigger rate: 0.0 Hz
14:37 - SPE trigger rate: 0.0 Hz
14:37 - Calibration trigger rate: 100.0 Hz
14:37 - Software trigger rate: 0.0 Hz
14:37 - Pedestal trigger rate: 10.0 Hz
14:37 - Collected trigger rate: 110.0 Hz
14:37 - Busy rate: 0.0 Hz
14:37 - Camera trigger rate: 110.0 Hz
14:37 - Status: TibState.Running ConnectionStatus: True
14:37 - Alarms: AlarmVector.ReadError
14:37 - Temperature: 35.56
14:37 - Local camera rate: 0.0 Hz
14:37 - Stereo trigger rate: 0.0 Hz
14:37 - SPE trigger rate: 0.0 Hz
14:37 - Calibration trigger rate: 100.0 Hz
14:37 - Software trigger rate: 0.0 Hz
14:37 - Pedestal trigger rate: 10.0 Hz
14:37 - Collected trigger rate: 110.0 Hz
14:37 - Busy rate: 0.0 Hz
14:37 - Camera trigger rate: 110.0 Hz
14:37 - Stopping TIB...
14:37 - Status: TibState.Running
14:37 - Alarms: AlarmVector.ReadError
14:37 - Connection status: True
14:37 - Disabling trigger
14:37 - Disabling PPS
14:37 - Status: TibState.PpsStopped
14:37 - Alarms: AlarmVector.ReadError
14:37 - Connection status: True
14:37 - Closing TIB connection to camera server
14:37 - Checking for high voltage locked pixels...
14:37 - Status: TibState.PpsStopped
14:37 - Alarms: AlarmVector.ReadError
14:37 - Connection status: False
14:37 - Run duration: 0:00:20
14:37 - Local camera triggers: 0
14:37 - Slow control triggers: 0
14:37 - Single photo-electron triggers: 0
14:37 - Calibration triggers: 1931
14:37 - Software triggers from UCTS: 0
14:37 - Pedestal triggers: 193
14:37 - Collected input triggers: 1934
14:37 - Busy triggers: 0
14:37 - Camera event triggers sent to clusters: 1934
14:37 - Checking for high voltage locked pixels...
14:38 - Checking for high voltage locked pixels...
14:38 - Stopping NMC
14:38 - Found 0 PPS errors.
14:38 - Starting NMC
14:38 - Clearing PPS error counters
14:38 - Checking for high voltage locked pixels...
14:39 - Configuring UCTS
14:39 - Configuring TIB...
14:39 - Setting TIB forced mode to False
14:39 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:39 - Status: TibState.PpsStopped
14:39 - Alarms: AlarmVector.ReadError
14:39 - Connection status: False
14:39 - Entering set_external_delay
14:39 - Setting ExternalDelayLocal to 0.000 ns
14:39 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
14:39 - Entering set_external_delay
14:39 - Setting ExternalDelayCalibration to 40.000 ns
14:39 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:39 - Entering set_external_delay
14:39 - Setting ExternalDelaySphe to 0.000 ns
14:39 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:39 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
14:39 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:39 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:39 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:39 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:39 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:39 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:39 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:39 - Status: TibState.PpsStopped
14:39 - Alarms: AlarmVector.ReadError
14:39 - Connection status: False
14:39 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:39 - Writing 10 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:39 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:39 - Writing 10 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:39 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:39 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:39 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:39 - Connecting TIB to camera server at 10.10.4.12:222
14:39 - Starting TIB...
14:39 - Status: TibState.PpsStopped
14:39 - Alarms: AlarmVector.ReadError
14:39 - Connection status: False
14:39 - Resetting run
14:39 - Wait for UCTS external trigger before enabling trigger...
14:39 - Status: TibState.Standby
14:39 - Alarms: AlarmVector.NoAlarm
14:39 - Connection status: False
14:39 - Status: TibState.Standby
14:39 - Alarms: AlarmVector.NoAlarm
14:39 - Connection status: False
14:39 - Status: TibState.Armed
14:39 - Alarms: AlarmVector.NoAlarm
14:39 - Connection status: True
14:39 - Starting TIB triggers...
14:39 - Enabling trigger
14:39 - Status: TibState.Running
14:39 - Alarms: AlarmVector.NoAlarm
14:39 - Connection status: True
14:39 - Checking for high voltage locked pixels...
14:39 - Status: TibState.Running ConnectionStatus: True
14:39 - Alarms: AlarmVector.ReadError
14:39 - Temperature: 35.56
14:39 - Local camera rate: 0.0 Hz
14:39 - Stereo trigger rate: 0.0 Hz
14:39 - SPE trigger rate: 0.0 Hz
14:39 - Calibration trigger rate: 100.0 Hz
14:39 - Software trigger rate: 0.0 Hz
14:39 - Pedestal trigger rate: 10.0 Hz
14:39 - Collected trigger rate: 110.0 Hz
14:39 - Busy rate: 0.0 Hz
14:39 - Camera trigger rate: 110.0 Hz
14:39 - Stopping TIB...
14:39 - Status: TibState.Running
14:39 - Alarms: AlarmVector.ReadError
14:39 - Connection status: True
14:39 - Disabling trigger
14:39 - Disabling PPS
14:39 - Status: TibState.PpsStopped
14:39 - Alarms: AlarmVector.ReadError
14:39 - Connection status: True
14:39 - Closing TIB connection to camera server
14:39 - Status: TibState.PpsStopped
14:39 - Alarms: AlarmVector.ReadError
14:39 - Connection status: False
14:39 - Run duration: 0:00:27
14:39 - Local camera triggers: 0
14:39 - Slow control triggers: 0
14:39 - Single photo-electron triggers: 0
14:39 - Calibration triggers: 2647
14:39 - Software triggers from UCTS: 0
14:39 - Pedestal triggers: 264
14:39 - Collected input triggers: 2265
14:39 - Busy triggers: 3
14:39 - Camera event triggers sent to clusters: 2262
14:39 - Checking for high voltage locked pixels...