15:56 - ECC is in state EccState.Ready with status EccStatus.NoError
15:56 - Average temperature: 21.8 deg C
15:56 - Air temperature (T1-T6 and T9-T10): 21.8, 22.0, 18.3, 22.1, 21.9, 23.0, 18.5, 17.0 deg C
15:56 - Air differential pressure: 63.6 Pa?
15:56 - Water temperature (T11-T12): 16.1, 15.0 deg C
15:56 - Back doors are closed.
15:56 - Light sensors: [0.8, 1.28, 1.74, 6.22] V
15:56 - Humidity: 37.9 %. Water pressure: [1.1, 0.84] bar.
15:56 - Fan speeds: [0.0, 0.0, 2400.0, 2280.0, 0.0, 0.0] rpm
15:56 - 24 V power supply no. 1 is enabled with a current of 55.400 A.
15:56 - Chiller is set to 13.00 degrees and has an actual bath temperature of 13.00 degrees
15:56 - Starting task "Check high voltages"
15:56 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:56 - Checking for high voltage locked pixels...
15:56 - Actual voltage is between 945.50 V and 1167.54 V.
15:56 - Low voltages range between 100.00 V and 100.00 V. 
15:56 - Reference voltages range between 945.26 V and 1167.15 V. 
15:56 - Maximum difference between expected and actual voltages is 0.71 V
15:57 - Maximum of current limits is 5647.07 uA
15:57 - Checking status of HVPA module in 61 drawer(s)...
15:57 - Checking status of HVPA channels in 61 drawer(s)...
15:57 - Checking for high voltage locked pixels...
15:57 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 2 channel(s)
15:57 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190329/NectarCAM_Run1130_newL1A.NMC.xml
15:57 - Done
15:57 - Finished task "Check high voltages"
15:57 - Starting NMC
15:57 - Clearing PPS error counters
15:57 - Configuring UCTS
15:57 - Configuring TIB...
15:57 - Setting TIB forced mode to False
15:57 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:57 - Status: TibState.Running
15:57 - Alarms: AlarmVector.ReadError
15:57 - Connection status: True
15:57 - Disabling PPS
15:57 - Error configuring TIB: Failed to call DisablePPS: Bad statuses are present
15:57 - Status: TibState.Running
15:57 - Alarms: AlarmVector.ReadError
15:57 - Connection status: True
15:57 - External delays: Local=0.000 ns, Calibration=40.000 ns, Sphe=0.000 ns
15:57 - Trigger mask: 0x54 = TriggerMask.SlowControl|Software|Calibration
15:57 - Input mask: 0x0
15:57 - Disable BUSY: False
15:57 - Extra BUSY Delay: 0.0
15:57 - Temperature: 35.62
15:57 - Stopping TIB...
15:57 - Status: TibState.Running
15:57 - Alarms: AlarmVector.ReadError
15:57 - Connection status: True
15:57 - Disabling trigger
15:57 - Disabling PPS
15:57 - Status: TibState.PpsStopped
15:57 - Alarms: AlarmVector.ReadError
15:57 - Connection status: True
15:57 - Closing TIB connection to camera server
15:57 - Checking for high voltage locked pixels...
15:57 - Configuring UCTS
15:57 - Configuring TIB...
15:57 - Setting TIB forced mode to False
15:57 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:57 - Status: TibState.PpsStopped
15:57 - Alarms: AlarmVector.ReadError
15:57 - Connection status: False
15:57 - Entering set_external_delay
15:57 - Setting ExternalDelayLocal to 0.000 ns
15:57 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:57 - Entering set_external_delay
15:57 - Setting ExternalDelayCalibration to 40.000 ns
15:57 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:57 - Entering set_external_delay
15:57 - Setting ExternalDelaySphe to 0.000 ns
15:57 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:57 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:57 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:57 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:57 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:57 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:57 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:57 - Status: TibState.PpsStopped
15:57 - Alarms: AlarmVector.ReadError
15:57 - Connection status: False
15:57 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:57 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:57 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:57 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:57 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:57 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:57 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:57 - Connecting TIB to camera server at 10.10.4.12:222
15:57 - Starting TIB...
15:57 - Status: TibState.PpsStopped
15:57 - Alarms: AlarmVector.ReadError
15:57 - Connection status: False
15:57 - Resetting run
15:57 - Wait for UCTS external trigger before enabling trigger...
15:57 - Status: TibState.Standby
15:57 - Alarms: AlarmVector.NoAlarm
15:57 - Connection status: False
15:57 - Status: TibState.Standby
15:57 - Alarms: AlarmVector.NoAlarm
15:57 - Connection status: False
15:57 - Status: TibState.Armed
15:57 - Alarms: AlarmVector.NoAlarm
15:57 - Connection status: True
15:57 - Starting TIB triggers...
15:57 - Enabling trigger
15:57 - Status: TibState.Running
15:57 - Alarms: AlarmVector.NoAlarm
15:57 - Connection status: True
15:57 - Configuring calibration box...
15:57 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=110 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
15:57 - Starting flashes...
15:58 - Checking for high voltage locked pixels...
15:58 - Stopping TIB...
15:58 - Status: TibState.Running
15:58 - Alarms: AlarmVector.ReadError
15:58 - Connection status: True
15:58 - Disabling trigger
15:58 - Disabling PPS
15:58 - Status: TibState.PpsStopped
15:58 - Alarms: AlarmVector.ReadError
15:58 - Connection status: True
15:58 - Closing TIB connection to camera server
15:58 - Status: TibState.PpsStopped
15:58 - Alarms: AlarmVector.ReadError
15:58 - Connection status: False
15:58 - Run duration: 0:00:30
15:58 - Local camera triggers: 0
15:58 - Slow control triggers: 0
15:58 - Single photo-electron triggers: 0
15:58 - Calibration triggers: 10998
15:58 - Software triggers from UCTS: 0
15:58 - Pedestal triggers: 0
15:58 - Collected input triggers: 10998
15:58 - Busy triggers: 0
15:58 - Camera event triggers sent to clusters: 10998
15:58 - Stopping NMC
15:58 - Found 0 PPS errors.