16:35 - Chiller is set to 13.00 degrees and has an actual bath temperature of 15.23 degrees
16:39 - Chiller is set to 13.00 degrees and has an actual bath temperature of 14.14 degrees
16:40 - Chiller is set to 13.00 degrees and has an actual bath temperature of 14.02 degrees
16:40 - Chiller is set to 13.00 degrees and has an actual bath temperature of 14.01 degrees
16:40 - Initializing Keithley 2000 Multimeter.
16:43 - Initializing Keithley 2000 Multimeter.
16:43 - Chiller is set to 13.00 degrees and has an actual bath temperature of 13.60 degrees
16:43 - Chiller is set to 13.00 degrees and has an actual bath temperature of 13.62 degrees
16:43 - Chiller is set to 13.00 degrees and has an actual bath temperature of 13.59 degrees
16:50 - Chiller is set to 13.00 degrees and has an actual bath temperature of 12.74 degrees
16:50 - Chiller is set to 13.00 degrees and has an actual bath temperature of 12.74 degrees
16:57 - Preparing ECC...
16:57 - Setting ECC temperature range for Ready state to [11.000000, 40.000000]
16:57 - Setting ECC mode to EccState.Ready
16:58 - ECC is in state EccState.Ready with status EccStatus.NoError
16:58 - Average temperature: 20.3 deg C
16:58 - Air temperature (T1-T6 and T9-T10): 20.3, 20.5, 17.9, 20.3, 20.3, 20.7, 17.8, 16.6 deg C
16:58 - Air differential pressure: 59.0 Pa?
16:58 - Water temperature (T11-T12): 15.7, 14.8 deg C
16:58 - Back doors are closed.
16:58 - Light sensors: [0.88, 1.35, 1.84, 6.07] V
16:58 - Humidity: 39.2 %. Water pressure: [1.08, 0.82] bar.
16:58 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
16:58 - 24 V power supply no. 1 is enabled with a current of 0.400 A.
17:01 - ECC is in state EccState.Ready with status EccStatus.NoError
17:01 - Average temperature: 20.4 deg C
17:01 - Air temperature (T1-T6 and T9-T10): 20.4, 20.4, 17.9, 20.2, 20.3, 20.6, 17.7, 16.6 deg C
17:01 - Air differential pressure: 59.8 Pa?
17:01 - Water temperature (T11-T12): 15.7, 14.8 deg C
17:01 - Back doors are closed.
17:01 - Light sensors: [0.84, 1.35, 1.84, 6.06] V
17:01 - Humidity: 39.3 %. Water pressure: [1.1, 0.82] bar.
17:01 - Fan speeds: [0.0, 0.0, 2280.0, 2280.0, 0.0, 0.0] rpm
17:01 - 24 V power supply no. 1 is enabled with a current of 0.600 A.
17:03 - ECC is in state EccState.Ready with status EccStatus.NoError
17:03 - Average temperature: 20.4 deg C
17:03 - Air temperature (T1-T6 and T9-T10): 20.4, 20.3, 17.8, 20.2, 20.2, 20.6, 17.7, 16.5 deg C
17:03 - Air differential pressure: 58.5 Pa?
17:03 - Water temperature (T11-T12): 15.7, 14.7 deg C
17:03 - Back doors are closed.
17:03 - Light sensors: [0.87, 1.36, 1.86, 6.06] V
17:03 - Humidity: 39.4 %. Water pressure: [1.08, 0.82] bar.
17:03 - Fan speeds: [0.0, 0.0, 2280.0, 2400.0, 0.0, 0.0] rpm
17:03 - 24 V power supply no. 1 is enabled with a current of 0.600 A.
17:06 - Chiller is set to 13.00 degrees and has an actual bath temperature of 13.01 degrees
17:06 - Initializing Keithley 2000 Multimeter.
17:07 - Scanning interface p4p1 for non configured modules...
17:07 - Found 0 MAC address(es)
17:09 - ECC is in state EccState.Ready with status EccStatus.NoError
17:09 - Average temperature: 20.3 deg C
17:09 - Air temperature (T1-T6 and T9-T10): 20.3, 20.2, 17.7, 20.1, 20.1, 20.5, 17.6, 16.5 deg C
17:09 - Air differential pressure: 61.6 Pa?
17:09 - Water temperature (T11-T12): 15.6, 14.7 deg C
17:09 - Back doors are closed.
17:09 - Light sensors: [0.84, 1.35, 1.85, 6.05] V
17:09 - Humidity: 39.5 %. Water pressure: [1.08, 0.82] bar.
17:09 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
17:09 - 24 V power supply no. 1 is enabled with a current of 0.600 A.
17:18 - Starting task "Powering modules..."
17:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:18 - Finished task "Powering modules..."
17:18 - ECC is in state EccState.Ready with status EccStatus.NoError
17:18 - Average temperature: 20.3 deg C
17:18 - Air temperature (T1-T6 and T9-T10): 20.3, 20.1, 17.7, 20.0, 20.0, 20.4, 17.5, 16.4 deg C
17:18 - Air differential pressure: 59.0 Pa?
17:18 - Water temperature (T11-T12): 15.6, 14.7 deg C
17:18 - Back doors are closed.
17:18 - Light sensors: [0.86, 1.36, 1.86, 6.04] V
17:18 - Humidity: 39.7 %. Water pressure: [1.1, 0.82] bar.
17:18 - Fan speeds: [0.0, 0.0, 2160.0, 2160.0, 0.0, 0.0] rpm
17:18 - 24 V power supply no. 1 is enabled with a current of 55.800 A.
17:20 - Scanning interface p4p1 for non configured modules...
17:20 - Found 61 MAC address(es)
17:21 - Starting task "Mask all trigger channels"
17:21 - Disabling all DTC trigger channels
17:22 - Finished task "Mask all trigger channels"
17:24 - Starting task "Configure modules"
17:24 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190327/config_61modules_cameraqm.NMC.xml
17:24 - Switching off high voltages in configuration
17:24 - Could not invoke the MethodCall service: BadTimeout
17:24 - Could not invoke the Read service: BadTimeout
17:24 - Finished task "Configure modules"
17:26 - Starting task "Configure modules"
17:26 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190327/config_61modules_cameraqm.NMC.xml
17:26 - Switching off high voltages in configuration
17:27 - Successfully configured 61 module(s)
17:27 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
17:27 - Found 0 PPS errors.
17:27 - Finished task "Configure modules"
17:28 - Starting task "Check high voltages"
17:28 - Found 0 drawer(s) in Nominal state, 0 in Low state and 61 in Wait state
17:28 - Actual voltage is between 0.00 V and 6.10 V.
17:28 - Low voltages range between 100.00 V and 100.00 V. 
17:28 - Reference voltages range between 945.26 V and 1167.15 V. 
17:28 - Maximum difference between expected and actual voltages is 6.10 V
17:28 - Maximum of current limits is 5647.07 uA
17:28 - Checking status of HVPA module in 61 drawer(s)...
17:28 - Checking status of HVPA channels in 61 drawer(s)...
17:28 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 427 channel(s)
17:28 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190327/config_61modules_cameraqm.NMC.xml
17:28 - Done
17:28 - Finished task "Check high voltages"
17:29 - Starting task "Switch HVPA voltage state"
17:29 - Setting HVPA current limit to 12489.75 uA
17:29 - Setting HVPA ramp speed to 35 V/s
17:29 - Switching HVPA to state Nominal
17:30 - Setting HVPA current limits...
17:30 - Finished task "Check high voltages"
17:31 - Starting task "Check high voltages"
17:31 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:31 - Actual voltage is between 11.59 V and 1166.93 V.
17:31 - Low voltages range between 100.00 V and 100.00 V. 
17:31 - Reference voltages range between 0.00 V and 1167.15 V. 
17:31 - Maximum difference between expected and actual voltages is 15.86 V
17:31 - Maximum of current limits is 5647.07 uA
17:31 - Checking status of HVPA module in 61 drawer(s)...
17:31 - HVPA module in drawer 83 has a status of 0x77!
17:31 - HVPA module in drawer 94 has a status of 0x7b!
17:31 - HVPA module in drawer 111 has a status of 0x7d!
17:31 - HVPA module in drawer 128 has a status of 0x3f!
17:31 - Checking status of HVPA channels in 61 drawer(s)...
17:31 - HVPA channel 1 of drawer 111 has status 0x8003!
17:31 - HVPA channel 2 of drawer 94 has status 0x8003!
17:31 - HVPA channel 3 of drawer 83 has status 0x8003!
17:31 - HVPA channel 6 of drawer 128 has status 0x8003!
17:31 - HV is locked in 4 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
17:31 - Resetting 4 channel(s)...
17:31 - Resetting HVPA channel 1 of drawer 111...
17:31 - Resetting HVPA channel 2 of drawer 94...
17:31 - Resetting HVPA channel 3 of drawer 83...
17:31 - Resetting HVPA channel 6 of drawer 128...
17:31 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190327/config_61modules_cameraqm.NMC.xml
17:32 - Done
17:32 - Finished task "Check high voltages"
17:32 - High voltage locked channels will be checked every 30 s
17:32 - Checking for high voltage locked pixels...
17:32 - Starting task "Check high voltages"
17:32 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:33 - Actual voltage is between 945.50 V and 1167.54 V.
17:33 - Low voltages range between 100.00 V and 100.00 V. 
17:33 - Checking for high voltage locked pixels...
17:33 - Reference voltages range between 945.26 V and 1167.15 V. 
17:33 - Maximum difference between expected and actual voltages is 0.71 V
17:33 - Maximum of current limits is 5647.07 uA
17:33 - Checking status of HVPA module in 61 drawer(s)...
17:33 - Checking status of HVPA channels in 61 drawer(s)...
17:33 - HV is stabilized in all channels.
17:33 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190327/config_61modules_cameraqm.NMC.xml
17:33 - Checking for high voltage locked pixels...
17:33 - Done
17:33 - Finished task "Check high voltages"
17:34 - Checking for high voltage locked pixels...
17:34 - Checking for high voltage locked pixels...
17:35 - Checking for high voltage locked pixels...
17:35 - Checking for high voltage locked pixels...
17:36 - Checking for high voltage locked pixels...
17:36 - Checking for high voltage locked pixels...
17:37 - Checking for high voltage locked pixels...
17:37 - Checking for high voltage locked pixels...
17:38 - Checking for high voltage locked pixels...
17:38 - Checking for high voltage locked pixels...
17:39 - Checking for high voltage locked pixels...
17:39 - Checking for high voltage locked pixels...
17:40 - Checking for high voltage locked pixels...
17:40 - Checking for high voltage locked pixels...
17:40 - Chiller is set to 13.00 degrees and has an actual bath temperature of 13.01 degrees
17:41 - Checking for high voltage locked pixels...
17:41 - Checking for high voltage locked pixels...
17:42 - Checking for high voltage locked pixels...
17:42 - Starting NMC
17:42 - Clearing PPS error counters
17:42 - Checking for high voltage locked pixels...
17:43 - Checking for high voltage locked pixels...
17:43 - Checking for high voltage locked pixels...
17:44 - Checking for high voltage locked pixels...
17:44 - Checking for high voltage locked pixels...
17:45 - Checking for high voltage locked pixels...
17:45 - Checking for high voltage locked pixels...
17:46 - Checking for high voltage locked pixels...
17:46 - Checking for high voltage locked pixels...
17:46 - Configuring calibration box...
17:46 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=110 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
17:47 - Checking for high voltage locked pixels...
17:47 - Checking for high voltage locked pixels...
17:48 - Checking for high voltage locked pixels...
17:48 - Checking for high voltage locked pixels...
17:49 - Checking for high voltage locked pixels...
17:49 - Checking for high voltage locked pixels...
17:50 - Checking for high voltage locked pixels...
17:50 - Checking for high voltage locked pixels...
17:51 - Checking for high voltage locked pixels...
17:51 - Configuring UCTS
17:51 - Configuring TIB...
17:51 - Setting TIB forced mode to False
17:51 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
17:51 - Status: TibState.RunStopped
17:51 - Alarms: AlarmVector.NoAlarm
17:51 - Connection status: False
17:51 - Disabling PPS
17:51 - Status: TibState.PpsStopped
17:51 - Alarms: AlarmVector.NoAlarm
17:51 - Connection status: False
17:51 - Entering set_external_delay
17:51 - Setting ExternalDelayLocal to 0.000 ns
17:51 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
17:51 - Entering set_external_delay
17:51 - Setting ExternalDelayCalibration to 40.000 ns
17:51 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
17:51 - Entering set_external_delay
17:51 - Setting ExternalDelaySphe to 0.000 ns
17:51 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
17:51 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
17:51 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
17:51 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
17:51 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
17:51 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
17:51 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
17:51 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
17:51 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
17:51 - Status: TibState.PpsStopped
17:51 - Alarms: AlarmVector.NoAlarm
17:51 - Connection status: False
17:51 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
17:51 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
17:51 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:51 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
17:51 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
17:51 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
17:51 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:51 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
17:51 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
17:51 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:51 - Checking for high voltage locked pixels...
17:51 - Status: TibState.PpsStopped
17:51 - Alarms: AlarmVector.NoAlarm
17:51 - Connection status: False
17:51 - External delays: Local=0.000 ns, Calibration=40.000 ns, Sphe=0.000 ns
17:51 - Trigger mask: 0x54 = TriggerMask.SlowControl|Software|Calibration
17:51 - Input mask: 0x0
17:51 - Disable BUSY: False
17:51 - Extra BUSY Delay: 0.0
17:51 - Temperature: 33.75
17:52 - Checking for high voltage locked pixels...
17:52 - Checking for high voltage locked pixels...
17:53 - Checking for high voltage locked pixels...
17:53 - Checking for high voltage locked pixels...
17:54 - Checking for high voltage locked pixels...
17:54 - Connecting TIB to camera server at 10.10.4.12:222
17:54 - Starting TIB...
17:54 - Status: TibState.PpsStopped
17:54 - Alarms: AlarmVector.NoAlarm
17:54 - Connection status: False
17:54 - Resetting run
17:54 - Wait for UCTS external trigger before enabling trigger...
17:54 - Status: TibState.Standby
17:54 - Alarms: AlarmVector.NoAlarm
17:54 - Connection status: False
17:54 - Status: TibState.Standby
17:54 - Alarms: AlarmVector.NoAlarm
17:54 - Connection status: False
17:54 - Status: TibState.Armed
17:54 - Alarms: AlarmVector.NoAlarm
17:54 - Connection status: True
17:54 - Checking for high voltage locked pixels...
17:55 - Checking for high voltage locked pixels...
17:55 - Starting TIB triggers...
17:55 - Enabling trigger
17:55 - Status: TibState.Running
17:55 - Alarms: AlarmVector.NoAlarm
17:55 - Connection status: True
17:55 - Checking for high voltage locked pixels...
17:55 - Configuring calibration box...
17:55 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=110 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
17:56 - Starting flashes...
17:56 - Checking for high voltage locked pixels...
17:56 - Checking for high voltage locked pixels...
17:56 - Stopping flashes...
17:57 - Checking for high voltage locked pixels...
17:57 - Stopping TIB...
17:57 - Status: TibState.Running
17:57 - Alarms: AlarmVector.ReadError
17:57 - Connection status: True
17:57 - Disabling trigger
17:57 - Disabling PPS
17:57 - Status: TibState.PpsStopped
17:57 - Alarms: AlarmVector.ReadError
17:57 - Connection status: True
17:57 - Closing TIB connection to camera server
17:57 - Status: TibState.PpsStopped
17:57 - Alarms: AlarmVector.ReadError
17:57 - Connection status: False
17:57 - Run duration: 0:02:47
17:57 - Local camera triggers: 0
17:57 - Slow control triggers: 0
17:57 - Single photo-electron triggers: 0
17:57 - Calibration triggers: 10983
17:57 - Software triggers from UCTS: 0
17:57 - Pedestal triggers: 0
17:57 - Collected input triggers: 10983
17:57 - Busy triggers: 0
17:57 - Camera event triggers sent to clusters: 10983
17:57 - Checking for high voltage locked pixels...
17:58 - Checking for high voltage locked pixels...
17:58 - Stopping NMC
17:58 - Found 0 PPS errors.
17:58 - Checking for high voltage locked pixels...
17:58 - Starting task "Check high voltages"
17:58 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:58 - Actual voltage is between 944.89 V and 1167.54 V.
17:58 - Low voltages range between 100.00 V and 100.00 V. 
17:59 - Reference voltages range between 945.26 V and 1167.15 V. 
17:59 - Checking for high voltage locked pixels...
17:59 - Maximum difference between expected and actual voltages is 0.69 V
17:59 - Maximum of current limits is 5647.07 uA
17:59 - Checking status of HVPA module in 61 drawer(s)...
17:59 - Checking status of HVPA channels in 61 drawer(s)...
17:59 - HV is stabilized in all channels.
17:59 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190327/config_61modules_cameraqm.NMC.xml
17:59 - Done
17:59 - Finished task "Check high voltages"
17:59 - Checking for high voltage locked pixels...
18:00 - Checking for high voltage locked pixels...
18:00 - Checking for high voltage locked pixels...
18:01 - Checking for high voltage locked pixels...
18:01 - Starting NMC
18:01 - Clearing PPS error counters
18:01 - ("NmcError: Failed to call 'NectarFrontEnd_097.Dtbp.readRegister': status Bad statuses are present, code 0xffffffff, status NmcStatus.Failed", 4294967295)
18:01 - Stopping NMC
18:01 - Found 0 PPS errors.
18:01 - Starting NMC
18:01 - Clearing PPS error counters
18:01 - Checking for high voltage locked pixels...
18:02 - Checking for high voltage locked pixels...
18:02 - Configuring UCTS
18:02 - Configuring TIB...
18:02 - Setting TIB forced mode to False
18:02 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
18:02 - Status: TibState.PpsStopped
18:02 - Alarms: AlarmVector.ReadError
18:02 - Connection status: False
18:02 - Entering set_external_delay
18:02 - Setting ExternalDelayLocal to 0.000 ns
18:02 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
18:02 - Entering set_external_delay
18:02 - Setting ExternalDelayCalibration to 40.000 ns
18:02 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
18:02 - Entering set_external_delay
18:02 - Setting ExternalDelaySphe to 0.000 ns
18:02 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
18:02 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
18:02 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
18:02 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
18:02 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
18:02 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
18:02 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
18:02 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
18:02 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
18:02 - Status: TibState.PpsStopped
18:02 - Alarms: AlarmVector.ReadError
18:02 - Connection status: False
18:02 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
18:02 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
18:02 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:02 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
18:02 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
18:02 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
18:02 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:02 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
18:02 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
18:02 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:02 - Checking for high voltage locked pixels...
18:02 - Connecting TIB to camera server at 10.10.4.12:222
18:02 - Starting TIB...
18:02 - Status: TibState.PpsStopped
18:02 - Alarms: AlarmVector.ReadError
18:02 - Connection status: False
18:02 - Resetting run
18:02 - Wait for UCTS external trigger before enabling trigger...
18:02 - Status: TibState.Standby
18:02 - Alarms: AlarmVector.NoAlarm
18:02 - Connection status: False
18:02 - Status: TibState.Standby
18:02 - Alarms: AlarmVector.NoAlarm
18:02 - Connection status: False
18:02 - Status: TibState.Armed
18:02 - Alarms: AlarmVector.NoAlarm
18:02 - Connection status: True
18:02 - Starting TIB triggers...
18:02 - Enabling trigger
18:02 - Status: TibState.Running
18:02 - Alarms: AlarmVector.NoAlarm
18:02 - Connection status: True
18:03 - Checking for high voltage locked pixels...
18:03 - Checking for high voltage locked pixels...
18:03 - Configuring calibration box...
18:03 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=110 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
18:04 - Checking for high voltage locked pixels...
18:04 - Checking for high voltage locked pixels...
18:04 - Starting flashes...
18:05 - Checking for high voltage locked pixels...
18:05 - Stopping flashes...
18:05 - Checking for high voltage locked pixels...
18:05 - Stopping TIB...
18:05 - Status: TibState.Running
18:05 - Alarms: AlarmVector.ReadError
18:05 - Connection status: True
18:05 - Disabling trigger
18:05 - Disabling PPS
18:05 - Status: TibState.PpsStopped
18:05 - Alarms: AlarmVector.ReadError
18:05 - Connection status: True
18:05 - Closing TIB connection to camera server
18:06 - Status: TibState.PpsStopped
18:06 - Alarms: AlarmVector.ReadError
18:06 - Connection status: False
18:06 - Run duration: 0:02:58
18:06 - Local camera triggers: 0
18:06 - Slow control triggers: 0
18:06 - Single photo-electron triggers: 0
18:06 - Calibration triggers: 10919
18:06 - Software triggers from UCTS: 0
18:06 - Pedestal triggers: 0
18:06 - Collected input triggers: 10919
18:06 - Busy triggers: 0
18:06 - Camera event triggers sent to clusters: 10919
18:06 - Checking for high voltage locked pixels...
18:06 - Checking for high voltage locked pixels...
18:06 - Stopping NMC
18:06 - Found 0 PPS errors.
18:07 - Checking for high voltage locked pixels...
18:07 - Checking for high voltage locked pixels...
18:08 - Checking for high voltage locked pixels...
18:08 - Checking for high voltage locked pixels...
18:09 - Checking for high voltage locked pixels...
18:09 - Checking for high voltage locked pixels...
18:10 - Checking for high voltage locked pixels...
18:10 - Checking for high voltage locked pixels...
18:11 - Checking for high voltage locked pixels...
18:11 - Checking for high voltage locked pixels...
18:12 - Checking for high voltage locked pixels...