12:58 - Starting task "Check high voltages"
12:58 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
12:59 - Checking for high voltage locked pixels...
12:59 - Actual voltage is between 944.89 V and 1166.93 V.
12:59 - Low voltages range between 100.00 V and 100.00 V. 
12:59 - Reference voltages range between 945.26 V and 1167.15 V. 
12:59 - Maximum difference between expected and actual voltages is 0.72 V
12:59 - Checking for high voltage locked pixels...
12:59 - Maximum of current limits is 5647.07 uA
12:59 - Checking status of HVPA module in 61 drawer(s)...
12:59 - Checking status of HVPA channels in 61 drawer(s)...
12:59 - HV is stabilized in all channels.
12:59 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190326/NectarCAM.Run1126.NMC.xml
12:59 - Done
12:59 - Finished task "Check high voltages"
12:59 - ECC is in state EccState.Ready with status EccStatus.NoError
12:59 - Average temperature: 22.3 deg C
12:59 - Air temperature (T1-T6 and T9-T10): 22.3, 22.7, 19.1, 22.8, 22.7, 23.7, 19.2, 17.8 deg C
12:59 - Air differential pressure: 62.2 Pa?
12:59 - Water temperature (T11-T12): 16.8, 15.8 deg C
12:59 - Back doors are closed.
12:59 - Light sensors: [5.32, 5.74, 6.15, 6.45] V
12:59 - Humidity: 54.3 %. Water pressure: [4.46, 4.87].
12:59 - Fan speeds: [0.0, 0.0, 2280.0, 2280.0, 0.0, 0.0] rpm
12:59 - 24 V power supply no. 1 is enabled with a current of 55.400 A.
12:59 - Stopping NMC
12:59 - Found 0 PPS errors.
12:59 - Starting NMC
12:59 - Clearing PPS error counters
13:00 - Configuring UCTS
13:00 - Configuring TIB...
13:00 - Setting TIB forced mode to False
13:00 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
13:00 - Status: TibState.PpsStopped
13:00 - Alarms: AlarmVector.ReadError
13:00 - Connection status: False
13:00 - Entering set_external_delay
13:00 - Setting ExternalDelayLocal to 0.000 ns
13:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
13:00 - Entering set_external_delay
13:00 - Setting ExternalDelayCalibration to 40.000 ns
13:00 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
13:00 - Entering set_external_delay
13:00 - Setting ExternalDelaySphe to 0.000 ns
13:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
13:00 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
13:00 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
13:00 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
13:00 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
13:00 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
13:00 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
13:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
13:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
13:00 - Status: TibState.PpsStopped
13:00 - Alarms: AlarmVector.ReadError
13:00 - Connection status: False
13:00 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
13:00 - Writing 333 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
13:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:00 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
13:00 - Writing 333 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
13:00 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
13:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:00 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
13:00 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
13:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:00 - Checking for high voltage locked pixels...
13:00 - Connecting TIB to camera server at 10.10.4.12:222
13:00 - Starting TIB...
13:00 - Status: TibState.PpsStopped
13:00 - Alarms: AlarmVector.ReadError
13:00 - Connection status: False
13:00 - Resetting run
13:00 - Wait for UCTS external trigger before enabling trigger...
13:00 - Status: TibState.Standby
13:00 - Alarms: AlarmVector.NoAlarm
13:00 - Connection status: False
13:00 - Status: TibState.Standby
13:00 - Alarms: AlarmVector.NoAlarm
13:00 - Connection status: False
13:00 - Status: TibState.Armed
13:00 - Alarms: AlarmVector.NoAlarm
13:00 - Connection status: True
13:00 - Starting TIB triggers...
13:00 - Enabling trigger
13:00 - Status: TibState.Running
13:00 - Alarms: AlarmVector.NoAlarm
13:00 - Connection status: True
13:00 - Configuring calibration box...
13:00 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=110 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=True
13:00 - Checking for high voltage locked pixels...
13:00 - Starting flashes...
13:00 - Stopping TIB...
13:00 - Status: TibState.Running
13:00 - Alarms: AlarmVector.ReadError
13:00 - Connection status: True
13:00 - Disabling trigger
13:00 - Disabling PPS
13:00 - Status: TibState.PpsStopped
13:00 - Alarms: AlarmVector.ReadError
13:00 - Connection status: True
13:00 - Closing TIB connection to camera server
13:01 - Status: TibState.PpsStopped
13:01 - Alarms: AlarmVector.ReadError
13:01 - Connection status: False
13:01 - Run duration: 0:00:50
13:01 - Local camera triggers: 0
13:01 - Slow control triggers: 0
13:01 - Single photo-electron triggers: 0
13:01 - Calibration triggers: 15344
13:01 - Software triggers from UCTS: 0
13:01 - Pedestal triggers: 0
13:01 - Collected input triggers: 15344
13:01 - Busy triggers: 0
13:01 - Camera event triggers sent to clusters: 15344
13:01 - Checking for high voltage locked pixels...