12:36 - Starting task "Set HV"
12:36 - Checking status of HVPA channels in 61 drawer(s)...
12:36 - HV is stabilized in all channels.
12:36 - Setting HV to nominal values...
12:36 - Setting channel 0 voltages to [1020.01, 994.43, 1041.95, 1042.61, 1026.57, 1019.55, 1005.84, 1007.41, 1047.31, 1028.92, 1006.58, 1029.66, 954.05, 1043.28, 965.44, 984.08, 1074.51, 996.57, 1051.23, 1093.49, 1023.67, 1115.75, 1038.25, 1071.04, 998.7, 1126.43, 1065.59, 1070.27, 1117.98, 963.22, 1014.5, 998.61, 1005.62, 1052.32, 985.26, 1017.72, 986.67, 1024.72, 1074.63, 1024.82, 1017.4, 1006.51, 1003.9, 989.68, 1026.71, 999.57, 1019.83, 1116.05, 1089.61, 1052.37, 1031.43, 1029.77, 1028.63, 1053.77, 1027.36, 1051.79, 1001.13, 1051.87, 1036.93, 1061.25, 1071.82]
12:36 - ECC is in state EccState.Ready with status EccStatus.NoError
12:36 - Average temperature: 22.3 deg C
12:36 - Air temperature (T1-T6 and T9-T10): 22.3, 22.7, 19.0, 22.8, 22.7, 23.7, 19.2, 17.8 deg C
12:36 - Air differential pressure: 60.8 Pa?
12:36 - Water temperature (T11-T12): 16.8, 15.9 deg C
12:36 - Back doors are closed.
12:36 - Light sensors: [5.39, 5.82, 6.24, 6.54] V
12:36 - Humidity: 55.1 %. Water pressure: [4.51, 4.93].
12:36 - Fan speeds: [0.0, 0.0, 2160.0, 2160.0, 0.0, 0.0] rpm
12:36 - 24 V power supply no. 1 is enabled with a current of 55.400 A.
12:36 - Setting channel 1 voltages to [1013.18, 971.24, 1049.84, 1008.37, 986.05, 965.49, 976.36, 963.83, 1019.1, 1055.92, 1032.94, 972.97, 996.32, 1043.27, 1023.91, 1048.09, 1012.83, 1011.42, 1064.19, 1026.08, 1001.03, 1132.81, 1089.79, 1004.62, 1117.91, 981.07, 1054.92, 1059.78, 1080.2, 1014.49, 1013.97, 1065.67, 1063.76, 957.02, 1008.85, 997.68, 1007.24, 1034.79, 1045.42, 1108.11, 1001.5, 1002.25, 1071.92, 1038.86, 1163.51, 1010.07, 1051.08, 1092.31, 1001.85, 1087.78, 1016.61, 1039.05, 1029.01, 1050.98, 1012.09, 953.38, 1015.64, 1052.02, 1054.34, 1036.28, 1122.37]
12:36 - Setting channel 2 voltages to [1052.16, 1012.86, 1073.5, 996.62, 953.06, 955.6, 979.4, 990.74, 1019.09, 1026.33, 1017.24, 979.81, 1023.96, 1088.62, 988.45, 1011.38, 1014.84, 1147.55, 1091.98, 1029.88, 1065.81, 992.45, 964.51, 974.64, 966.0, 1050.16, 1015.33, 1052.23, 1144.37, 1021.77, 999.73, 1057.73, 1079.04, 968.09, 1005.87, 971.96, 1065.34, 1027.26, 1149.04, 1005.48, 1017.82, 1023.99, 973.42, 1019.97, 1102.81, 1000.52, 1045.61, 978.2, 1041.51, 1063.64, 1112.69, 1000.07, 1020.09, 1103.49, 978.32, 1016.79, 985.84, 1041.78, 1057.25, 1060.96, 1076.54]
12:36 - Setting channel 3 voltages to [1020.57, 1099.01, 1039.49, 1036.36, 1008.12, 951.8, 991.84, 1001.54, 1028.38, 1057.69, 998.26, 1118.54, 1107.48, 1047.36, 977.98, 1015.68, 1057.27, 999.65, 1037.35, 1089.16, 1045.15, 1091.67, 1041.47, 989.95, 984.3, 1056.16, 1024.58, 1131.2, 1073.44, 1074.17, 1042.95, 976.42, 1027.08, 1090.7, 1103.09, 997.71, 1047.99, 990.67, 1098.02, 1035.97, 1009.9, 1050.16, 1029.82, 1061.88, 1117.41, 1019.15, 1018.68, 1013.94, 984.12, 1136.56, 1083.99, 1145.89, 1077.47, 983.61, 1100.77, 1016.91, 976.17, 1037.28, 1069.17, 1095.68, 1033.49]
12:36 - Setting channel 4 voltages to [1066.79, 1073.32, 1049.01, 983.55, 993.17, 1005.15, 1034.8, 989.68, 1039.71, 983.92, 1075.01, 1019.98, 1024.85, 1095.48, 995.85, 998.39, 1033.92, 1073.02, 1054.75, 1065.43, 1049.25, 1090.65, 1084.51, 1027.38, 1000.99, 971.85, 1045.14, 1087.44, 1057.23, 1075.25, 1035.15, 983.17, 1042.69, 957.4, 1081.32, 988.02, 970.26, 1002.41, 1099.78, 1039.54, 1050.56, 1046.85, 1095.59, 1063.73, 1044.38, 1033.74, 992.06, 1016.46, 1045.72, 1106.74, 1056.89, 1087.9, 1016.11, 1025.98, 978.7, 971.04, 1075.34, 974.12, 1079.26, 964.27, 989.18]
12:36 - Setting channel 5 voltages to [1054.36, 1015.99, 997.22, 1036.88, 1042.64, 983.25, 1004.57, 1044.0, 1025.18, 1071.0, 1131.17, 986.25, 1047.77, 1032.45, 1082.77, 1016.77, 1064.02, 1017.17, 1025.58, 1062.59, 1007.27, 1137.02, 1011.66, 1012.38, 1020.08, 1047.32, 1006.44, 1039.32, 1099.84, 1045.16, 971.53, 1030.49, 1044.42, 1003.41, 1035.2, 1063.79, 1033.19, 1025.49, 1069.93, 1007.95, 1124.27, 1031.66, 1004.33, 1060.13, 986.51, 1011.71, 1028.94, 981.26, 1101.73, 1095.57, 1071.85, 1068.98, 1057.83, 1059.28, 1097.59, 985.47, 995.09, 1034.06, 1030.45, 1167.15, 1131.84]
12:37 - Setting channel 6 voltages to [1061.65, 1049.49, 1028.61, 1070.76, 993.17, 1016.4, 961.19, 945.26, 1046.43, 1019.57, 1049.95, 979.17, 1039.65, 1057.58, 1003.19, 1040.0, 1066.6, 1035.14, 1031.55, 1137.11, 1022.39, 1011.56, 982.24, 1001.73, 1024.74, 1062.38, 1025.47, 999.67, 1067.97, 1014.44, 961.98, 1040.52, 1030.9, 996.41, 1035.56, 1019.5, 1056.23, 987.86, 1108.18, 1062.41, 1046.39, 1004.34, 1007.17, 1002.0, 1157.37, 1015.55, 1030.52, 1017.71, 991.04, 1074.09, 1089.99, 1032.69, 1001.62, 985.84, 1030.51, 971.05, 974.27, 1021.03, 1159.49, 996.3, 1067.66]
12:37 - Checking status of HVPA channels in 61 drawer(s)...
12:37 - HV is stabilized in all channels.
12:37 - Finished task "Set HV"
12:38 - Starting task "Check high voltages"
12:38 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
12:38 - Actual voltage is between 945.50 V and 1167.54 V.
12:38 - Low voltages range between 100.00 V and 100.00 V. 
12:39 - Reference voltages range between 945.26 V and 1167.15 V. 
12:39 - Maximum difference between expected and actual voltages is 0.71 V
12:39 - Maximum of current limits is 5647.07 uA
12:39 - Checking status of HVPA module in 61 drawer(s)...
12:39 - Checking status of HVPA channels in 61 drawer(s)...
12:39 - HV is stabilized in all channels.
12:39 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190326/NectarCAM.Run1126.NMC.xml
12:39 - Done
12:39 - Finished task "Check high voltages"
12:39 - High voltage locked channels will be checked every 30 s
12:39 - Stopping NMC
12:39 - Found 0 PPS errors.
12:39 - Starting NMC
12:39 - Clearing PPS error counters
12:39 - Configuring UCTS
12:39 - Configuring TIB...
12:39 - Setting TIB forced mode to False
12:39 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
12:39 - Status: TibState.PpsStopped
12:39 - Alarms: AlarmVector.ReadError
12:39 - Connection status: False
12:39 - Entering set_external_delay
12:39 - Setting ExternalDelayLocal to 0.000 ns
12:39 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
12:39 - Entering set_external_delay
12:39 - Setting ExternalDelayCalibration to 40.000 ns
12:39 - Writing 40.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
12:39 - Entering set_external_delay
12:39 - Setting ExternalDelaySphe to 0.000 ns
12:39 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
12:39 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
12:39 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
12:39 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
12:39 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
12:39 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
12:39 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
12:39 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
12:39 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
12:39 - Status: TibState.PpsStopped
12:39 - Alarms: AlarmVector.ReadError
12:39 - Connection status: False
12:39 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
12:39 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
12:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:39 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
12:39 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
12:39 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
12:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:39 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
12:39 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
12:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:39 - Connecting TIB to camera server at 10.10.4.12:222
12:39 - Starting TIB...
12:39 - Status: TibState.PpsStopped
12:39 - Alarms: AlarmVector.ReadError
12:39 - Connection status: False
12:39 - Resetting run
12:39 - Wait for UCTS external trigger before enabling trigger...
12:39 - Status: TibState.Standby
12:39 - Alarms: AlarmVector.NoAlarm
12:39 - Connection status: False
12:39 - Status: TibState.Standby
12:39 - Alarms: AlarmVector.NoAlarm
12:39 - Connection status: False
12:39 - Status: TibState.Armed
12:39 - Alarms: AlarmVector.NoAlarm
12:39 - Connection status: True
12:39 - Starting TIB triggers...
12:39 - Enabling trigger
12:39 - Status: TibState.Running
12:39 - Alarms: AlarmVector.NoAlarm
12:39 - Connection status: True
12:39 - Configuring calibration box...
12:39 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=350 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=True
12:39 - Starting flashes...
12:40 - Checking for high voltage locked pixels...
12:40 - Checking for high voltage locked pixels...
12:40 - Stopping TIB...
12:40 - Status: TibState.Running
12:40 - Alarms: AlarmVector.ReadError
12:40 - Connection status: True
12:40 - Disabling trigger
12:40 - Disabling PPS
12:40 - Status: TibState.PpsStopped
12:40 - Alarms: AlarmVector.ReadError
12:40 - Connection status: True
12:40 - Closing TIB connection to camera server
12:40 - Status: TibState.PpsStopped
12:40 - Alarms: AlarmVector.ReadError
12:40 - Connection status: False
12:40 - Run duration: 0:00:58
12:40 - Local camera triggers: 0
12:40 - Slow control triggers: 0
12:40 - Single photo-electron triggers: 0
12:40 - Calibration triggers: 37551
12:40 - Software triggers from UCTS: 0
12:40 - Pedestal triggers: 0
12:40 - Collected input triggers: 37551
12:40 - Busy triggers: 0
12:40 - Camera event triggers sent to clusters: 37551
12:40 - Stopping NMC
12:41 - Found 0 PPS errors.
12:41 - Checking for high voltage locked pixels...