11:12 - ECC is in state EccState.Ready with status EccStatus.NoError
11:12 - Average temperature: 22.2 deg C
11:12 - Air temperature (T1-T6 and T9-T10): 22.2, 22.5, 18.6, 22.5, 22.2, 23.4, 18.9, 17.3 deg C
11:12 - Air differential pressure: 62.3 Pa?
11:12 - Water temperature (T11-T12): 16.6, 15.6 deg C
11:12 - Back doors are closed.
11:12 - Light sensors: [10.3, 9.85, 10.3, 10.3] V
11:12 - Humidity: 103.0 %. Water pressure: [10.3, 10.3].
11:12 - Fan speeds: [0.0, 0.0, 2280.0, 2280.0, 0.0, 0.0] rpm
11:12 - 24 V power supply no. 1 is enabled with a current of 244.000 A.
11:12 - Starting task "Check high voltages"
11:12 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:12 - Checking for high voltage locked pixels...
11:12 - Actual voltage is between 947.94 V and 1172.42 V.
11:12 - Low voltages range between 100.00 V and 100.00 V. 
11:12 - Reference voltages range between 948.03 V and 1172.15 V. 
11:12 - Maximum difference between expected and actual voltages is 1.09 V
11:12 - Checking for high voltage locked pixels...
11:12 - Maximum of current limits is 5647.07 uA
11:12 - Checking status of HVPA module in 61 drawer(s)...
11:12 - Checking status of HVPA channels in 61 drawer(s)...
11:13 - HV is stabilized in all channels.
11:13 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190325/config_cameraqm_61modules_DACL.NMC.xml
11:13 - Done
11:13 - Finished task "Check high voltages"
11:13 - Checking for high voltage locked pixels...
11:13 - Starting NMC
11:13 - Clearing PPS error counters
11:13 - Checking for high voltage locked pixels...
11:14 - Configuring UCTS
11:14 - Configuring TIB...
11:14 - Setting TIB forced mode to False
11:14 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:14 - Status: TibState.PpsStopped
11:14 - Alarms: AlarmVector.BufferFull|AlmostFull
11:14 - Connection status: False
11:14 - Entering set_external_delay
11:14 - Setting ExternalDelayLocal to 0.000 ns
11:14 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:14 - Entering set_external_delay
11:14 - Setting ExternalDelayCalibration to 76.000 ns
11:14 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:14 - Entering set_external_delay
11:14 - Setting ExternalDelaySphe to 0.000 ns
11:14 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:14 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
11:14 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:14 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:14 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:14 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:14 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:14 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:14 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:14 - Status: TibState.PpsStopped
11:14 - Alarms: AlarmVector.BufferFull|AlmostFull
11:14 - Connection status: False
11:14 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:14 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:14 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:14 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:14 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:14 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:14 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:14 - Connecting TIB to camera server at 10.10.4.12:222
11:14 - Starting TIB...
11:14 - Status: TibState.PpsStopped
11:14 - Alarms: AlarmVector.BufferFull|AlmostFull
11:14 - Connection status: False
11:14 - Resetting run
11:14 - Wait for UCTS external trigger before enabling trigger...
11:14 - Status: TibState.Standby
11:14 - Alarms: AlarmVector.NoAlarm
11:14 - Connection status: False
11:14 - Status: TibState.Standby
11:14 - Alarms: AlarmVector.NoAlarm
11:14 - Connection status: False
11:14 - Status: TibState.Armed
11:14 - Alarms: AlarmVector.NoAlarm
11:14 - Connection status: True
11:14 - Checking for high voltage locked pixels...
11:14 - Starting TIB triggers...
11:14 - Enabling trigger
11:14 - Status: TibState.Running
11:14 - Alarms: AlarmVector.NoAlarm
11:14 - Connection status: True
11:14 - Configuring calibration box...
11:14 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=110 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
11:14 - Starting flashes...
11:14 - Checking for high voltage locked pixels...
11:15 - Stopping flashes...
11:15 - Stopping TIB...
11:15 - Status: TibState.Running
11:15 - Alarms: AlarmVector.BufferFull|AlmostFull
11:15 - Connection status: True
11:15 - Disabling trigger
11:15 - Disabling PPS
11:15 - Status: TibState.PpsStopped
11:15 - Alarms: AlarmVector.BufferFull|AlmostFull
11:15 - Connection status: True
11:15 - Closing TIB connection to camera server
11:15 - Checking for high voltage locked pixels...
11:15 - Status: TibState.PpsStopped
11:15 - Alarms: AlarmVector.BufferFull|AlmostFull
11:15 - Connection status: False
11:15 - Run duration: 0:01:18
11:15 - Local camera triggers: 0
11:15 - Slow control triggers: 0
11:15 - Single photo-electron triggers: 0
11:15 - Calibration triggers: 10911
11:15 - Software triggers from UCTS: 0
11:15 - Pedestal triggers: 0
11:15 - Collected input triggers: 10911
11:15 - Busy triggers: 0
11:15 - Camera event triggers sent to clusters: 10911
11:15 - Stopping NMC
11:15 - Found 0 PPS errors.