17:42 - Successfully configured 61 module(s)
17:42 - Checking for high voltage locked pixels...
17:42 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
17:42 - Found 0 PPS errors.
17:42 - Finished task "Configure modules"
17:42 - Starting task "Switch HVPA voltage state"
17:42 - Setting HVPA current limit to 12489.75 uA
17:42 - Checking for high voltage locked pixels...
17:42 - Stopped periodic check of locked high voltages
17:42 - Setting HVPA ramp speed to 35 V/s
17:42 - Switching HVPA to state Nominal
17:43 - Setting HVPA current limits...
17:43 - Finished task "Switch HVPA voltage state"
17:43 - Resetting NMC
17:43 - Starting task "Configure modules"
17:43 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1104.NMC.xml
17:43 - Successfully configured 61 module(s)
17:43 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
17:43 - Found 0 PPS errors.
17:43 - Finished task "Configure modules"
17:43 - Starting task "Switch HVPA voltage state"
17:43 - Setting HVPA current limit to 12489.75 uA
17:44 - Setting HVPA ramp speed to 35 V/s
17:44 - Switching HVPA to state Nominal
17:44 - Setting HVPA current limits...
17:44 - ECC is in state EccState.Ready with status EccStatus.NoError
17:44 - ECC temperature sensors: T1= 26.0, T2= 25.5, T3= 26.8, T4= 27.7 deg C
17:44 - Back doors are closed.
17:44 - Light sensors: [0, 0, 0, 0] V
17:44 - Humidity: 0.0 %. Water pressure: [0.0, 0.0].
17:44 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
17:44 - 24 V power supply no. 1 is enabled with a current of 60.800 A.
17:44 - Finished task "Switch HVPA voltage state"
17:44 - Starting task "Check high voltages"
17:44 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:44 - Actual voltage is between 143.96 V and 1173.03 V.
17:44 - Low voltages range between 100.00 V and 100.00 V. 
17:45 - Reference voltages range between 948.03 V and 1172.93 V. 
17:45 - Maximum difference between expected and actual voltages is 926.46 V
17:45 - Maximum of current limits is 5647.07 uA
17:45 - Checking status of HVPA module in 61 drawer(s)...
17:45 - HVPA module in drawer 113 has a status of 0x3f!
17:45 - HVPA module in drawer 115 has a status of 0x7b!
17:45 - HVPA module in drawer 116 has a status of 0x5d!
17:45 - HVPA module in drawer 118 has a status of 0x6f!
17:45 - HVPA module in drawer 127 has a status of 0x7b!
17:45 - HVPA module in drawer 131 has a status of 0x67!
17:45 - HVPA module in drawer 147 has a status of 0x1f!
17:45 - HVPA module in drawer 149 has a status of 0x4f!
17:45 - HVPA module in drawer 153 has a status of 0x7e!
17:45 - HVPA module in drawer 163 has a status of 0x77!
17:45 - HVPA module in drawer 164 has a status of 0x6b!
17:45 - HVPA module in drawer 166 has a status of 0x5f!
17:45 - HVPA module in drawer 167 has a status of 0x77!
17:45 - Checking status of HVPA channels in 61 drawer(s)...
17:45 - HVPA channel 0 of drawer 153 has status 0x8003!
17:45 - HVPA channel 1 of drawer 116 has status 0x8003!
17:45 - HVPA channel 2 of drawer 115 has status 0x8003!
17:45 - HVPA channel 2 of drawer 127 has status 0x8003!
17:45 - HVPA channel 2 of drawer 164 has status 0x8007!
17:45 - HVPA channel 3 of drawer 131 has status 0x8003!
17:45 - HVPA channel 3 of drawer 163 has status 0x8003!
17:45 - HVPA channel 3 of drawer 167 has status 0x8007!
17:45 - HVPA channel 4 of drawer 118 has status 0x8003!
17:45 - HVPA channel 4 of drawer 131 has status 0x8003!
17:45 - HVPA channel 4 of drawer 149 has status 0x8003!
17:45 - HVPA channel 4 of drawer 164 has status 0x8007!
17:45 - HVPA channel 5 of drawer 116 has status 0x8003!
17:45 - HVPA channel 5 of drawer 147 has status 0x8003!
17:45 - HVPA channel 5 of drawer 149 has status 0x8003!
17:45 - HVPA channel 5 of drawer 166 has status 0x8007!
17:45 - HVPA channel 6 of drawer 113 has status 0x8003!
17:45 - HVPA channel 6 of drawer 147 has status 0x8003!
17:45 - HV is locked in 18 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
17:45 - Resetting 18 channel(s)...
17:45 - Resetting HVPA channel 0 of drawer 153...
17:45 - Resetting HVPA channel 1 of drawer 116...
17:45 - Resetting HVPA channel 2 of drawer 115...
17:45 - Resetting HVPA channel 2 of drawer 127...
17:45 - Resetting HVPA channel 2 of drawer 164...
17:45 - Resetting HVPA channel 3 of drawer 131...
17:45 - Resetting HVPA channel 3 of drawer 163...
17:45 - Resetting HVPA channel 3 of drawer 167...
17:45 - Resetting HVPA channel 4 of drawer 118...
17:45 - Resetting HVPA channel 4 of drawer 131...
17:45 - Resetting HVPA channel 4 of drawer 149...
17:45 - Resetting HVPA channel 4 of drawer 164...
17:45 - Resetting HVPA channel 5 of drawer 116...
17:45 - Resetting HVPA channel 5 of drawer 147...
17:45 - Resetting HVPA channel 5 of drawer 149...
17:45 - Resetting HVPA channel 5 of drawer 166...
17:45 - Resetting HVPA channel 6 of drawer 113...
17:45 - Resetting HVPA channel 6 of drawer 147...
17:45 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1104.NMC.xml
17:45 - Reference voltage of channel 5 in drawer #149: expected 1020.07, read 0.00
17:45 - Done
17:45 - Finished task "Check high voltages"
17:45 - Starting task "Check high voltages"
17:45 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:46 - Actual voltage is between 120.17 V and 1173.03 V.
17:46 - Low voltages range between 100.00 V and 100.00 V. 
17:46 - Reference voltages range between 0.00 V and 1172.93 V. 
17:46 - Maximum difference between expected and actual voltages is 109.80 V
17:46 - Maximum of current limits is 5647.07 uA
17:46 - Checking status of HVPA module in 61 drawer(s)...
17:46 - HVPA module in drawer 149 has a status of 0x5f!
17:46 - Checking status of HVPA channels in 61 drawer(s)...
17:46 - HVPA channel 5 of drawer 149 has status 0x8003!
17:46 - HV is locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
17:46 - Resetting 1 channel(s)...
17:46 - Resetting HVPA channel 5 of drawer 149...
17:46 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1104.NMC.xml
17:46 - Done
17:46 - Finished task "Check high voltages"
17:46 - Starting task "Check high voltages"
17:46 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:47 - Actual voltage is between 804.59 V and 1173.03 V.
17:47 - Low voltages range between 100.00 V and 100.00 V. 
17:47 - Reference voltages range between 948.03 V and 1172.93 V. 
17:47 - Maximum difference between expected and actual voltages is 0.89 V
17:47 - Maximum of current limits is 5647.07 uA
17:47 - Checking status of HVPA module in 61 drawer(s)...
17:47 - Checking status of HVPA channels in 61 drawer(s)...
17:47 - HV is stabilized in all channels.
17:47 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1104.NMC.xml
17:47 - Done
17:47 - Finished task "Check high voltages"
17:47 - High voltage locked channels will be checked every 30 s
17:47 - Starting NMC
17:47 - Clearing PPS error counters
17:48 - Configuring UCTS
17:48 - Configuring TIB...
17:48 - Setting TIB forced mode to False
17:48 - Writing False to serveur.TIB.Forced.ForcedMode.ForcedMode_v
17:48 - Status: TibState.PpsStopped
17:48 - Alarms: AlarmVector.NoAlarm
17:48 - Connection status: False
17:48 - Entering set_external_delay
17:48 - Setting ExternalDelayLocal to 0.000 ns
17:48 - Writing 0.0 to serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
17:48 - Failed to write 'serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v': - overallStatus : Bad statuses are present - requestHandle : 7 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09
17:48 - Writing 56.0 to serveur.TIB.ExternalDelay.ExternalDelay_v
17:48 - Setting TIB trigger mode to 0x58 = TriggerMask.SlowControl|Software|SPhE
17:48 - Writing 88 to serveur.TIB.TriggerMode.ModeMask.ModeMask_v
17:48 - Writing 0 to serveur.TIB.InputsEnable.InputMask.InputMask_v
17:48 - Writing False to serveur.TIB.BUSY.DisableBusy.DisableBusy_v
17:48 - Writing 0.0 to serveur.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
17:48 - Writing False to serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v
17:48 - Failed to write 'serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v': - overallStatus : Bad statuses are present - requestHandle : 19 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09
17:48 - Writing False to serveur.TIB.Throttler.DisableThrottlerBP.DisableThrottlerBP_v
17:48 - Writing False to serveur.TIB.Throttler.DisableThrottlerWR.DisableThrottlerWR_v
17:48 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP50us.MaxTriggersBP50us_v
17:48 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR50us.MaxTriggersWR50us_v
17:48 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP1ms.MaxTriggersBP1ms_v
17:48 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR1ms.MaxTriggersWR1ms_v
17:48 - Status: TibState.PpsStopped
17:48 - Alarms: AlarmVector.NoAlarm
17:48 - Connection status: False
17:48 - Writing False to serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
17:48 - Failed to write 'serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v': - overallStatus : Bad statuses are present - requestHandle : 35 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09
17:48 - Connecting TIB to camera server at 10.10.4.12:222
17:48 - Starting TIB...
17:48 - Status: TibState.PpsStopped
17:48 - Alarms: AlarmVector.NoAlarm
17:48 - Connection status: True
17:48 - Resetting run
17:48 - Wait for UCTS external trigger before enabling trigger...
17:48 - Status: TibState.Standby
17:48 - Alarms: AlarmVector.NoAlarm
17:48 - Connection status: True
17:48 - Status: TibState.Standby
17:48 - Alarms: AlarmVector.NoAlarm
17:48 - Connection status: True
17:48 - Status: TibState.CoutingPps
17:48 - Alarms: AlarmVector.NoAlarm
17:48 - Connection status: True
17:48 - Starting TIB triggers...
17:48 - Enabling trigger
17:48 - Status: TibState.Running
17:48 - Alarms: AlarmVector.NoAlarm
17:48 - Connection status: True
17:48 - Checking for high voltage locked pixels...
17:48 - Checking for high voltage locked pixels...
17:49 - Checking for high voltage locked pixels...
17:49 - Checking for high voltage locked pixels...
17:49 - Configuring calibration box...
17:49 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=400 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
17:49 - Starting flashes...
17:50 - Checking for high voltage locked pixels...
17:50 - Stopping TIB...
17:50 - Status: TibState.Running
17:50 - Alarms: AlarmVector.NoAlarm
17:50 - Connection status: True
17:50 - Disabling trigger
17:50 - Disabling PPS
17:50 - Status: TibState.PpsStopped
17:50 - Alarms: AlarmVector.NoAlarm
17:50 - Connection status: True
17:50 - Closing TIB connection to camera server
17:50 - Checking for high voltage locked pixels...
17:50 - Status: TibState.PpsStopped
17:50 - Alarms: AlarmVector.NoAlarm
17:50 - Connection status: False
17:50 - Run duration: 0:02:43
17:50 - Local camera triggers: 0
17:50 - Slow control triggers: 0
17:50 - Single photo-electron triggers: 39901
17:50 - Calibration triggers: 0
17:50 - Software triggers from UCTS: 0
17:50 - Pedestal triggers: 1059033
17:50 - Collected input triggers: 39901
17:50 - Busy triggers: 0
17:50 - Camera event triggers sent to clusters: 39901
17:51 - Stopping NMC
17:51 - Found 0 PPS errors.