08:49 - ECC is in state EccState.Ready with status EccStatus.NoError
08:49 - ECC temperature sensors: T1= 24.9, T2= 24.4, T3= 25.6, T4= 26.5 deg C
08:49 - Back doors are closed.
08:49 - Light sensors: [0, 0, 0, 0] V
08:49 - Humidity: 0.0 %. Water pressure: [0.0, 0.0].
08:49 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
08:49 - 24 V power supply no. 1 is enabled with a current of -0.100 A.
08:49 - Starting task "Powering modules..."
08:49 - Executing command '/opt/cta/bin/cta_ctrl --all --power_off' on Digital Trigger Crate at 10.10.4.59
08:49 - Finished task "Powering modules..."
08:49 - Starting task "Powering modules..."
08:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.59
08:50 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.59
08:50 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.59
08:50 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.59
08:50 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.59
08:50 - Finished task "Powering modules..."
08:50 - ECC is in state EccState.Ready with status EccStatus.NoError
08:50 - ECC temperature sensors: T1= 24.9, T2= 24.4, T3= 25.6, T4= 26.5 deg C
08:50 - Back doors are closed.
08:50 - Light sensors: [0, 0, 0, 0] V
08:50 - Humidity: 0.0 %. Water pressure: [0.0, 0.0].
08:50 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
08:50 - 24 V power supply no. 1 is enabled with a current of 60.600 A.
08:50 - Starting task "Configure modules"
08:50 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1104.NMC.xml
08:50 - Successfully configured 61 module(s)
08:50 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
08:50 - Found 0 PPS errors.
08:50 - Finished task "Configure modules"
09:08 - Starting task "Switch HVPA voltage state"
09:08 - Setting HVPA current limit to 12489.75 uA
09:08 - Setting HVPA ramp speed to 35 V/s
09:08 - Switching HVPA to state Nominal
09:09 - Setting HVPA current limits...
09:09 - Finished task "Switch HVPA voltage state"
09:10 - High voltage locked channels will be checked every 30 s
09:10 - Checking for high voltage locked pixels...
09:10 - Module 81 has 1 pixel(s) locked (HVPA status of 0x3f)!
09:10 - Module 130 has 1 pixel(s) locked (HVPA status of 0x3f)!
09:10 - Module 163 has 1 pixel(s) locked (HVPA status of 0x77)!
09:10 - Unlocking 3 channel(s)...
09:10 - Resetting HVPA channel 6 of drawer 81...
09:10 - Resetting HVPA channel 6 of drawer 130...
09:10 - Resetting HVPA channel 3 of drawer 163...
09:11 - Checking for high voltage locked pixels...
09:11 - Checking for high voltage locked pixels...
09:11 - Starting task "Check high voltages"
09:11 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
09:11 - Actual voltage is between 947.94 V and 1173.64 V.
09:11 - Low voltages range between 100.00 V and 100.00 V. 
09:12 - Reference voltages range between 948.03 V and 1172.93 V. 
09:12 - Checking for high voltage locked pixels...
09:12 - Maximum difference between expected and actual voltages is 0.68 V
09:12 - Maximum of current limits is 5647.07 uA
09:12 - Checking status of HVPA module in 61 drawer(s)...
09:12 - Checking status of HVPA channels in 61 drawer(s)...
09:12 - HV is stabilized in all channels.
09:12 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1104.NMC.xml
09:12 - Done
09:12 - Finished task "Check high voltages"
09:12 - Checking for high voltage locked pixels...
09:13 - Checking for high voltage locked pixels...
09:13 - Checking for high voltage locked pixels...
09:14 - Checking for high voltage locked pixels...
09:14 - Starting NMC
09:14 - Clearing PPS error counters
09:14 - Checking for high voltage locked pixels...
09:15 - Checking for high voltage locked pixels...
09:15 - Checking for high voltage locked pixels...
09:16 - Checking for high voltage locked pixels...
09:16 - Checking for high voltage locked pixels...
09:17 - Checking for high voltage locked pixels...
09:17 - Checking for high voltage locked pixels...
09:18 - Checking for high voltage locked pixels...
09:18 - Checking for high voltage locked pixels...
09:19 - Checking for high voltage locked pixels...
09:19 - Checking for high voltage locked pixels...
09:19 - Configuring UCTS
09:19 - Configuring TIB...
09:19 - Setting TIB forced mode to False
09:19 - Writing False to serveur.TIB.Forced.ForcedMode.ForcedMode_v
09:19 - Status: TibState.PpsStopped
09:19 - Alarms: AlarmVector.NoAlarm
09:19 - Connection status: False
09:19 - Entering set_external_delay
09:19 - Setting ExternalDelayLocal to 0.000 ns
09:19 - Writing 0.0 to serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
09:19 - Failed to write 'serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v': - overallStatus : Bad statuses are present - requestHandle : 7 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09
09:19 - Writing 56.0 to serveur.TIB.ExternalDelay.ExternalDelay_v
09:19 - Setting TIB trigger mode to 0x58 = TriggerMask.SlowControl|Software|SPhE
09:19 - Writing 88 to serveur.TIB.TriggerMode.ModeMask.ModeMask_v
09:19 - Writing 0 to serveur.TIB.InputsEnable.InputMask.InputMask_v
09:19 - Writing False to serveur.TIB.BUSY.DisableBusy.DisableBusy_v
09:19 - Writing 0.0 to serveur.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
09:19 - Writing False to serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v
09:19 - Failed to write 'serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v': - overallStatus : Bad statuses are present - requestHandle : 19 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09
09:19 - Writing False to serveur.TIB.Throttler.DisableThrottlerBP.DisableThrottlerBP_v
09:19 - Writing False to serveur.TIB.Throttler.DisableThrottlerWR.DisableThrottlerWR_v
09:19 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP50us.MaxTriggersBP50us_v
09:19 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR50us.MaxTriggersWR50us_v
09:19 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP1ms.MaxTriggersBP1ms_v
09:19 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR1ms.MaxTriggersWR1ms_v
09:19 - Status: TibState.PpsStopped
09:19 - Alarms: AlarmVector.NoAlarm
09:19 - Connection status: False
09:19 - Writing False to serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
09:19 - Failed to write 'serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v': - overallStatus : Bad statuses are present - requestHandle : 35 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09
09:19 - Connecting TIB to camera server at 10.10.4.12:222
09:19 - Starting TIB...
09:19 - Status: TibState.PpsStopped
09:19 - Alarms: AlarmVector.NoAlarm
09:19 - Connection status: False
09:19 - Resetting run
09:19 - Wait for UCTS external trigger before enabling trigger...
09:19 - Status: TibState.Standby
09:19 - Alarms: AlarmVector.NoAlarm
09:19 - Connection status: True
09:19 - Status: TibState.Standby
09:19 - Alarms: AlarmVector.NoAlarm
09:19 - Connection status: True
09:19 - Status: TibState.Armed
09:19 - Alarms: AlarmVector.NoAlarm
09:19 - Connection status: True
09:19 - Starting TIB triggers...
09:19 - Enabling trigger
09:19 - Status: TibState.Running
09:19 - Alarms: AlarmVector.NoAlarm
09:19 - Connection status: True
09:20 - Configuring calibration box...
09:20 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=400 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
09:20 - Starting flashes...
09:20 - Checking for high voltage locked pixels...
09:20 - Checking for high voltage locked pixels...
09:20 - Stopping TIB...
09:20 - Status: TibState.Running
09:20 - Alarms: AlarmVector.NoAlarm
09:20 - Connection status: True
09:20 - Disabling trigger
09:20 - Disabling PPS
09:20 - Status: TibState.PpsStopped
09:20 - Alarms: AlarmVector.NoAlarm
09:20 - Connection status: True
09:20 - Closing TIB connection to camera server
09:21 - Stopped periodic check of locked high voltages
09:22 - Stopping NMC
09:22 - Found 0 PPS errors.