11:30 - Setting HVPA ramp speed to 35 V/s 11:31 - Switching HVPA to state Nominal 11:31 - Setting HVPA current limits... 11:31 - Finished task "Switch HVPA voltage state" 11:32 - Starting task "Check high voltages" 11:32 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state 11:32 - Actual voltage is between 61.61 V and 1177.91 V. 11:32 - Low voltages range between 100.00 V and 100.00 V. 11:32 - Reference voltages range between 0.00 V and 1177.93 V. 11:33 - Maximum difference between expected and actual voltages is 57.95 V 11:33 - Maximum of current limits is 5647.07 uA 11:33 - Checking status of HVPA module in 61 drawer(s)... 11:33 - HVPA module in drawer 131 has a status of 0x77! 11:33 - Checking status of HVPA channels in 61 drawer(s)... 11:33 - HVPA channel 3 of drawer 131 has status 0x8003! 11:33 - HV is locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s) 11:33 - Resetting 1 channel(s)... 11:33 - Resetting HVPA channel 3 of drawer 131... 11:33 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1098+5V.NMC.xml 11:33 - Done 11:33 - Finished task "Check high voltages" 12:28 - Starting task "Check high voltages" 12:28 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state 12:28 - Actual voltage is between 952.82 V and 1177.91 V. 12:28 - Low voltages range between 100.00 V and 100.00 V. 12:28 - Reference voltages range between 953.03 V and 1177.93 V. 12:28 - Maximum difference between expected and actual voltages is 0.76 V 12:28 - Maximum of current limits is 5647.07 uA 12:28 - Checking status of HVPA module in 61 drawer(s)... 12:28 - Checking status of HVPA channels in 61 drawer(s)... 12:29 - ECC is in state EccState.Ready with status EccStatus.NoError 12:29 - ECC temperature sensors: T1= 24.2, T2= 23.8, T3= 24.9, T4= 25.9 deg C 12:29 - Back doors are closed. 12:29 - Light sensors: [0, 0, 0, 0] V 12:29 - Humidity: 0.0 %. Water pressure: [0.0, 0.0]. 12:29 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm 12:29 - 24 V power supply no. 1 is enabled with a current of 61.800 A. 12:29 - High voltage locked channels will be checked every 30 s 12:29 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s) 12:29 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190308/config_61modules_run1098+5V.NMC.xml 12:29 - Done 12:29 - Finished task "Check high voltages" 12:29 - Configuring UCTS 12:29 - Configuring TIB... 12:29 - Setting TIB forced mode to False 12:29 - Writing False to serveur.TIB.Forced.ForcedMode.ForcedMode_v 12:29 - Status: TibState.PpsStopped 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: False 12:29 - Entering set_external_delay 12:29 - Setting ExternalDelayLocal to 0.000 ns 12:29 - Writing 0.0 to serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v 12:29 - Failed to write 'serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v': - overallStatus : Bad statuses are present - requestHandle : 7 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09 12:29 - Writing 56.0 to serveur.TIB.ExternalDelay.ExternalDelay_v 12:29 - Setting TIB trigger mode to 0x58 = TriggerMask.SlowControl|Software|SPhE 12:29 - Writing 88 to serveur.TIB.TriggerMode.ModeMask.ModeMask_v 12:29 - Writing 0 to serveur.TIB.InputsEnable.InputMask.InputMask_v 12:29 - Writing False to serveur.TIB.BUSY.DisableBusy.DisableBusy_v 12:29 - Writing 0.0 to serveur.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v 12:29 - Writing False to serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v 12:29 - Failed to write 'serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v': - overallStatus : Bad statuses are present - requestHandle : 19 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09 12:29 - Writing False to serveur.TIB.Throttler.DisableThrottlerBP.DisableThrottlerBP_v 12:29 - Writing False to serveur.TIB.Throttler.DisableThrottlerWR.DisableThrottlerWR_v 12:29 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP50us.MaxTriggersBP50us_v 12:29 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR50us.MaxTriggersWR50us_v 12:29 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP1ms.MaxTriggersBP1ms_v 12:29 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR1ms.MaxTriggersWR1ms_v 12:29 - Status: TibState.PpsStopped 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: False 12:29 - Writing False to serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v 12:29 - Failed to write 'serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v': - overallStatus : Bad statuses are present - requestHandle : 35 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09 12:29 - Connecting TIB to camera server at 10.10.4.12:222 12:29 - Starting TIB... 12:29 - Status: TibState.PpsStopped 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: False 12:29 - Resetting run 12:29 - Wait for UCTS external trigger before enabling trigger... 12:29 - Status: TibState.Standby 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: False 12:29 - Status: TibState.Standby 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: True 12:29 - Status: TibState.Armed 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: True 12:29 - Starting TIB triggers... 12:29 - Enabling trigger 12:29 - Status: TibState.Running 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: True 12:29 - Configuring calibration box... 12:29 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=400 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False 12:29 - Starting flashes... 12:29 - Checking for high voltage locked pixels... 12:29 - Stopping flashes... 12:29 - Stopping TIB... 12:29 - Status: TibState.Running 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: True 12:29 - Disabling trigger 12:29 - Disabling PPS 12:29 - Status: TibState.PpsStopped 12:29 - Alarms: AlarmVector.NoAlarm 12:29 - Connection status: True 12:29 - Closing TIB connection to camera server 12:29 - Stopping NMC 12:29 - Found 0 PPS errors. 12:30 - Starting NMC 12:30 - Clearing PPS error counters 12:30 - Checking for high voltage locked pixels... 12:30 - Checking for high voltage locked pixels... 12:30 - Configuring UCTS 12:30 - Configuring TIB... 12:30 - Setting TIB forced mode to False 12:30 - Writing False to serveur.TIB.Forced.ForcedMode.ForcedMode_v 12:30 - Status: TibState.PpsStopped 12:30 - Alarms: AlarmVector.NoAlarm 12:30 - Connection status: False 12:30 - Entering set_external_delay 12:30 - Setting ExternalDelayLocal to 0.000 ns 12:30 - Writing 0.0 to serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v 12:30 - Failed to write 'serveur.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v': - overallStatus : Bad statuses are present - requestHandle : 7 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09 12:30 - Writing 56.0 to serveur.TIB.ExternalDelay.ExternalDelay_v 12:30 - Setting TIB trigger mode to 0x58 = TriggerMask.SlowControl|Software|SPhE 12:30 - Writing 88 to serveur.TIB.TriggerMode.ModeMask.ModeMask_v 12:30 - Writing 0 to serveur.TIB.InputsEnable.InputMask.InputMask_v 12:30 - Writing False to serveur.TIB.BUSY.DisableBusy.DisableBusy_v 12:30 - Writing 0.0 to serveur.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v 12:30 - Writing False to serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v 12:30 - Failed to write 'serveur.TIB.Throttler.DisableThrottler.DisableThrottler_v': - overallStatus : Bad statuses are present - requestHandle : 19 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09 12:30 - Writing False to serveur.TIB.Throttler.DisableThrottlerBP.DisableThrottlerBP_v 12:30 - Writing False to serveur.TIB.Throttler.DisableThrottlerWR.DisableThrottlerWR_v 12:30 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP50us.MaxTriggersBP50us_v 12:30 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR50us.MaxTriggersWR50us_v 12:30 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP1ms.MaxTriggersBP1ms_v 12:30 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR1ms.MaxTriggersWR1ms_v 12:30 - Status: TibState.PpsStopped 12:30 - Alarms: AlarmVector.NoAlarm 12:30 - Connection status: False 12:30 - Writing False to serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v 12:30 - Failed to write 'serveur.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v': - overallStatus : Bad statuses are present - requestHandle : 35 - targets[] - targets[0] status: The server could not successfully process the Write service: BadNodeIdUnknown: The server could not successfully process the Write service: BadNodeIdUnknown - opcUaStatusCode : 2.15089e+09 12:30 - Connecting TIB to camera server at 10.10.4.12:222 12:30 - Starting TIB... 12:30 - Status: TibState.PpsStopped 12:30 - Alarms: AlarmVector.NoAlarm 12:30 - Connection status: True 12:30 - Resetting run 12:30 - Wait for UCTS external trigger before enabling trigger... 12:30 - Status: TibState.Standby 12:30 - Alarms: AlarmVector.NoAlarm 12:30 - Connection status: True 12:30 - Status: TibState.Standby 12:30 - Alarms: AlarmVector.NoAlarm 12:30 - Connection status: True 12:30 - Status: TibState.CoutingPps 12:30 - Alarms: AlarmVector.NoAlarm 12:30 - Connection status: True 12:30 - Starting TIB triggers... 12:30 - Enabling trigger 12:30 - Status: TibState.Running 12:30 - Alarms: AlarmVector.NoAlarm 12:30 - Connection status: True 12:31 - Checking for high voltage locked pixels... 12:31 - Configuring calibration box... 12:31 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=400 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False 12:31 - Starting flashes... 12:31 - Checking for high voltage locked pixels... 12:32 - Checking for high voltage locked pixels... 12:32 - Checking for high voltage locked pixels... 12:32 - Stopping TIB... 12:32 - Status: TibState.Running 12:32 - Alarms: AlarmVector.NoAlarm 12:32 - Connection status: True 12:32 - Disabling trigger 12:32 - Disabling PPS 12:32 - Status: TibState.PpsStopped 12:32 - Alarms: AlarmVector.NoAlarm 12:32 - Connection status: True 12:32 - Closing TIB connection to camera server 12:32 - Status: TibState.PpsStopped 12:32 - Alarms: AlarmVector.NoAlarm 12:32 - Connection status: False 12:32 - Run duration: 0:01:49 12:32 - Local camera triggers: 0 12:32 - Slow control triggers: 0 12:32 - Single photo-electron triggers: 39977 12:32 - Calibration triggers: 0 12:32 - Software triggers from UCTS: 0 12:32 - Pedestal triggers: 707979 12:32 - Collected input triggers: 39977 12:32 - Busy triggers: 0 12:32 - Camera event triggers sent to clusters: 39977 12:32 - Stopping NMC 12:32 - Found 0 PPS errors. 12:32 - Stopped periodic check of locked high voltages