10:10 - ECC is in state EccState.Ready with status EccStatus.NoError
10:10 - ECC temperature sensors: T1= 25.6, T2= 25.2, T3= 26.4, T4= 27.3 deg C
10:10 - Back doors are closed.
10:10 - Light sensors: [0, 0, 0, 0] V
10:10 - Humidity: 0.0 %. Water pressure: [0.0, 0.0].
10:10 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
10:10 - 24 V power supply no. 1 is enabled with a current of 65.200 A.
10:10 - Starting task "Check high voltages"
10:10 - Found 8 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:10 - Actual voltage is between 966.85 V and 1122.40 V.
10:10 - Low voltages range between 100.00 V and 100.00 V. 
10:10 - Reference voltages range between 966.36 V and 1122.57 V. 
10:10 - Maximum difference between expected and actual voltages is 0.69 V
10:10 - Maximum of current limits is 5262.16 uA
10:10 - Checking status of HVPA module in 8 drawer(s)...
10:10 - Checking status of HVPA channels in 8 drawer(s)...
10:10 - HV is stabilized in all channels.
10:10 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190221/NectarCAM.Run1088.NMC.xml
10:11 - Done
10:11 - Finished task "Check high voltages"
10:11 - Stopping NMC
10:11 - Found 0 PPS errors.
10:11 - Starting NMC
10:11 - Clearing PPS error counters
10:11 - Configuring UCTS
10:11 - Configuring TIB...
10:11 - Setting TIB forced mode to False
10:11 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:11 - Status: TibState.PpsStopped
10:11 - Alarms: AlarmVector.ReadError
10:11 - Connection status: False
10:11 - Entering set_external_delay
10:11 - Setting ExternalDelayLocal to 0.000 ns
10:11 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:11 - Entering set_external_delay
10:11 - Setting ExternalDelayCalibration to 76.000 ns
10:11 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:11 - Entering set_external_delay
10:11 - Setting ExternalDelaySphe to 0.000 ns
10:11 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:11 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:11 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:11 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:11 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:11 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:11 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:11 - Status: TibState.PpsStopped
10:11 - Alarms: AlarmVector.ReadError
10:11 - Connection status: False
10:11 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:11 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:11 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:11 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:11 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11 - Connecting TIB to camera server at 10.10.4.12:222
10:11 - Starting TIB...
10:11 - Status: TibState.PpsStopped
10:11 - Alarms: AlarmVector.ReadError
10:11 - Connection status: False
10:11 - Resetting run
10:11 - Wait for UCTS external trigger before enabling trigger...
10:11 - Status: TibState.Standby
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Status: TibState.Standby
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Status: TibState.Armed
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: True
10:11 - Starting TIB triggers...
10:11 - Enabling trigger
10:11 - Status: TibState.Running
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: True
10:11 - Configuring calibration box...
10:11 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=500 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
10:11 - Starting flashes...
10:12 - Stopping TIB...
10:12 - Status: TibState.Running
10:12 - Alarms: AlarmVector.ReadError
10:12 - Connection status: True
10:12 - Disabling trigger
10:12 - Disabling PPS
10:12 - Status: TibState.PpsStopped
10:12 - Alarms: AlarmVector.ReadError
10:12 - Connection status: True
10:12 - Closing TIB connection to camera server
10:12 - Status: TibState.PpsStopped
10:12 - Alarms: AlarmVector.ReadError
10:12 - Connection status: False
10:12 - Run duration: 0:01:19
10:12 - Local camera triggers: 0
10:12 - Slow control triggers: 0
10:12 - Single photo-electron triggers: 0
10:12 - Calibration triggers: 49913
10:12 - Software triggers from UCTS: 0
10:12 - Pedestal triggers: 0
10:12 - Collected input triggers: 49913
10:12 - Busy triggers: 0
10:12 - Camera event triggers sent to clusters: 49913
10:12 - Stopping NMC
10:12 - Found 0 PPS errors.