17:59 - ECC is in state EccState.Ready with status EccStatus.NoError
17:59 - ECC temperature sensors: T1= 26.0, T2= 25.3, T3= 26.6, T4= 27.4 deg C
17:59 - Back doors are closed.
17:59 - Light sensors: [0, 0, 0, 0] V
17:59 - Humidity: 0.0 %. Water pressure: [0.0, 0.0].
17:59 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
17:59 - 24 V power supply no. 1 is enabled with a current of 51.500 A.
17:59 - Starting task "Check high voltages"
17:59 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:59 - Actual voltage is between 944.28 V and 1202.92 V.
17:59 - Low voltages range between 100.00 V and 100.00 V. 
17:59 - Reference voltages range between 943.80 V and 1203.01 V. 
17:59 - Maximum difference between expected and actual voltages is 0.92 V
17:59 - Maximum of current limits is 5647.07 uA
17:59 - Checking status of HVPA module in 53 drawer(s)...
17:59 - Checking status of HVPA channels in 53 drawer(s)...
17:59 - HV is stabilized in all channels.
17:59 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190204/config_53modules_l0delay_15pe.NMC.xml
18:00 - Done
18:00 - Finished task "Check high voltages"
18:00 - Starting NMC
18:00 - Clearing PPS error counters
18:00 - Configuring UCTS
18:00 - Configuring TIB...
18:00 - Setting TIB forced mode to False
18:00 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
18:00 - Status: TibState.PpsStopped
18:00 - Alarms: AlarmVector.ReadError
18:00 - Connection status: False
18:00 - Entering set_external_delay
18:00 - Setting ExternalDelayLocal to 0.000 ns
18:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
18:00 - Entering set_external_delay
18:00 - Setting ExternalDelayCalibration to 76.000 ns
18:00 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
18:00 - Entering set_external_delay
18:00 - Setting ExternalDelaySphe to 0.000 ns
18:00 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
18:00 - Setting TIB trigger mode to 0x51 = TriggerMask.SlowControl|Software|Mono
18:00 - Writing 81 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
18:00 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
18:00 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
18:00 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
18:00 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
18:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
18:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
18:00 - Status: TibState.PpsStopped
18:00 - Alarms: AlarmVector.ReadError
18:00 - Connection status: False
18:00 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
18:00 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
18:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:00 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
18:00 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
18:00 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
18:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:00 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
18:00 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
18:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:01 - Connecting TIB to camera server at 10.10.4.12:222
18:01 - Starting TIB...
18:01 - Status: TibState.PpsStopped
18:01 - Alarms: AlarmVector.ReadError
18:01 - Connection status: False
18:01 - Resetting run
18:01 - Wait for UCTS external trigger before enabling trigger...
18:01 - Status: TibState.Standby
18:01 - Alarms: AlarmVector.NoAlarm
18:01 - Connection status: False
18:01 - Status: TibState.Standby
18:01 - Alarms: AlarmVector.NoAlarm
18:01 - Connection status: False
18:01 - Status: TibState.Armed
18:01 - Alarms: AlarmVector.NoAlarm
18:01 - Connection status: True
18:01 - Starting TIB triggers...
18:01 - Enabling trigger
18:01 - Status: TibState.Running
18:01 - Alarms: AlarmVector.NoAlarm
18:01 - Connection status: True
18:03 - Status: TibState.Running ConnectionStatus: True
18:03 - Alarms: AlarmVector.ReadError
18:03 - Temperature: 37.50
18:03 - Local camera rate: 0.0 Hz
18:03 - Stereo trigger rate: 0.0 Hz
18:03 - SPE trigger rate: 0.0 Hz
18:03 - Calibration trigger rate: 0.0 Hz
18:03 - Software trigger rate: 0.0 Hz
18:03 - Pedestal trigger rate: 0.0 Hz
18:03 - Collected trigger rate: 1.0 Hz
18:03 - Busy rate: 0.0 Hz
18:03 - Camera trigger rate: 1.0 Hz
09:14 - Stopping TIB...
09:14 - Status: TibState.Running
09:14 - Alarms: AlarmVector.ReadError
09:14 - Connection status: True
09:14 - Disabling trigger
09:14 - Disabling PPS
09:14 - Status: TibState.PpsStopped
09:14 - Alarms: AlarmVector.ReadError
09:14 - Connection status: True
09:14 - Closing TIB connection to camera server
09:14 - Status: TibState.PpsStopped
09:14 - Alarms: AlarmVector.ReadError
09:14 - Connection status: False
09:14 - Run duration: 15:13:11
09:14 - Local camera triggers: 0
09:14 - Slow control triggers: 0
09:14 - Single photo-electron triggers: 0
09:14 - Calibration triggers: 0
09:14 - Software triggers from UCTS: 0
09:14 - Pedestal triggers: 0
09:14 - Collected input triggers: 13015
09:14 - Busy triggers: 0
09:14 - Camera event triggers sent to clusters: 13015
09:14 - Stopping NMC
09:14 - Found 0 PPS errors.
09:14 - Starting task "Check high voltages"
09:14 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
09:14 - Actual voltage is between 944.28 V and 1202.92 V.
09:14 - Low voltages range between 100.00 V and 100.00 V. 
09:14 - Reference voltages range between 943.80 V and 1203.01 V. 
09:14 - Maximum difference between expected and actual voltages is 0.94 V
09:14 - Maximum of current limits is 5647.07 uA
09:14 - Checking status of HVPA module in 53 drawer(s)...
09:14 - Checking status of HVPA channels in 53 drawer(s)...
09:15 - HV is stabilized in all channels.
09:15 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190204/config_53modules_l0delay_15pe.NMC.xml
09:15 - Done
09:15 - Finished task "Check high voltages"