15:45 - Status: TibState.RunStopped
15:45 - Alarms: AlarmVector.NoAlarm
15:45 - Connection status: False
15:45 - External delays: Local=3825.000 ns, Calibration=3825.000 ns, Sphe=3825.000 ns
15:45 - Trigger mask: 0x51 = TriggerMask.SlowControl|Software|Mono
15:45 - Input mask: 0x7
15:45 - Disable BUSY: False
15:45 - Extra BUSY Delay: 0.0
15:45 - Temperature: 38.25
15:46 - ECC is in state EccState.Ready with status EccStatus.NoError
15:46 - ECC temperature sensors: T1= 26.3, T2= 25.8, T3= 27.1, T4= 28.1 deg C
15:46 - 24 V power supply no. 1 is enabled with a current of 63.800 A.
15:46 - Starting task "Check high voltages"
15:46 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190116/NectarCAM_Run1062_54m_L1A_2it.NMC.xml
15:46 - Done
15:46 - Found 54 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:46 - Low voltages range between 100.00 V and 100.00 V. 
15:47 - Reference voltages range between 943.80 V and 1198.89 V. 
15:47 - Actual voltage is between 943.67 V and 1199.26 V.
15:47 - Maximum difference between expected and actual voltages is 0.70 V
15:47 - Maximum of current limits is 5647.07 uA
15:47 - Checking status of HVPA module in 54 drawer(s)...
15:47 - Checking status of HVPA channels in 54 drawer(s)...
15:47 - HV is stabilized in all channels.
15:47 - Finished task "Check high voltages"
15:47 - Starting NMC
15:47 - Clearing PPS error counters
15:47 - Configuring UCTS
15:47 - Configuring TIB...
15:47 - Setting TIB forced mode to False
15:47 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:47 - Status: TibState.RunStopped
15:47 - Alarms: AlarmVector.NoAlarm
15:47 - Connection status: False
15:47 - Disabling PPS
15:47 - Status: TibState.PpsStopped
15:47 - Alarms: AlarmVector.NoAlarm
15:47 - Connection status: False
15:47 - Entering set_external_delay
15:47 - Setting ExternalDelayLocal to 0.000 ns
15:47 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:47 - Entering set_external_delay
15:47 - Setting ExternalDelayCalibration to 76.000 ns
15:47 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:47 - Entering set_external_delay
15:47 - Setting ExternalDelaySphe to 0.000 ns
15:47 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:47 - Setting TIB trigger mode to 0x60 = TriggerMask.SlowControl|Pedestal
15:47 - Writing 96 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:47 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:47 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:47 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:47 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:47 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:47 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:47 - Status: TibState.PpsStopped
15:47 - Alarms: AlarmVector.NoAlarm
15:47 - Connection status: False
15:47 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:47 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:47 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:47 - Writing True to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:47 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:47 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:47 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:47 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:47 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:47 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:48 - Connecting TIB to camera server at 10.10.4.12:222
15:48 - Starting TIB...
15:48 - Status: TibState.PpsStopped
15:48 - Alarms: AlarmVector.NoAlarm
15:48 - Connection status: False
15:48 - Resetting run
15:48 - Wait for UCTS external trigger before enabling trigger...
15:48 - Status: TibState.Standby
15:48 - Alarms: AlarmVector.NoAlarm
15:48 - Connection status: False
15:48 - Status: TibState.Standby
15:48 - Alarms: AlarmVector.NoAlarm
15:48 - Connection status: False
15:48 - Status: TibState.Armed
15:48 - Alarms: AlarmVector.NoAlarm
15:48 - Connection status: True
15:48 - Starting TIB triggers...
15:48 - Enabling trigger
15:48 - Status: TibState.Running
15:48 - Alarms: AlarmVector.NoAlarm
15:48 - Connection status: True
15:48 - Status: TibState.Running ConnectionStatus: True
15:48 - Alarms: AlarmVector.ReadError
15:48 - Temperature: 38.31
15:48 - Local camera rate: 0.0 Hz
15:48 - Stereo trigger rate: 0.0 Hz
15:48 - SPE trigger rate: 0.0 Hz
15:48 - Calibration trigger rate: 0.0 Hz
15:48 - Software trigger rate: 0.0 Hz
15:48 - Pedestal trigger rate: 987.0 Hz
15:48 - Collected trigger rate: 987.0 Hz
15:48 - Busy rate: 178.0 Hz
15:48 - Camera trigger rate: 809.0 Hz
15:48 - Status: TibState.Running ConnectionStatus: True
15:48 - Alarms: AlarmVector.ReadError
15:48 - Temperature: 38.31
15:48 - Local camera rate: 0.0 Hz
15:48 - Stereo trigger rate: 0.0 Hz
15:48 - SPE trigger rate: 0.0 Hz
15:48 - Calibration trigger rate: 0.0 Hz
15:48 - Software trigger rate: 0.0 Hz
15:48 - Pedestal trigger rate: 1042.0 Hz
15:48 - Collected trigger rate: 1042.0 Hz
15:48 - Busy rate: 218.0 Hz
15:48 - Camera trigger rate: 824.0 Hz
15:48 - Stopping TIB...
15:48 - Status: TibState.Running
15:48 - Alarms: AlarmVector.ReadError
15:48 - Connection status: True
15:48 - Disabling trigger
15:48 - Disabling PPS
15:48 - Status: TibState.PpsStopped
15:48 - Alarms: AlarmVector.ReadError
15:48 - Connection status: True
15:48 - Closing TIB connection to camera server
15:48 - Status: TibState.PpsStopped
15:48 - Alarms: AlarmVector.ReadError
15:48 - Connection status: False
15:48 - Run duration: 0:00:16
15:48 - Local camera triggers: 0
15:48 - Slow control triggers: 0
15:48 - Single photo-electron triggers: 0
15:48 - Calibration triggers: 0
15:48 - Software triggers from UCTS: 0
15:48 - Pedestal triggers: 15173
15:48 - Collected input triggers: 13995
15:48 - Busy triggers: 2712
15:48 - Camera event triggers sent to clusters: 11283
15:48 - Stopping NMC
15:48 - Found 0 PPS errors.
15:48 - Starting task "Check high voltages"
15:48 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190116/NectarCAM_Run1062_54m_L1A_2it.NMC.xml
15:48 - Done
15:48 - Found 54 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:48 - Low voltages range between 100.00 V and 100.00 V. 
15:48 - Reference voltages range between 943.80 V and 1198.89 V. 
15:49 - Actual voltage is between 943.67 V and 1199.26 V.
15:49 - Maximum difference between expected and actual voltages is 0.81 V
15:49 - Maximum of current limits is 5647.07 uA
15:49 - Checking status of HVPA module in 54 drawer(s)...
15:49 - Checking status of HVPA channels in 54 drawer(s)...
15:49 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
15:49 - Finished task "Check high voltages"