10:39 - ECC is in state EccState.Ready with status EccStatus.NoError
10:39 - ECC temperature sensors: T1= 26.4, T2= 26.0, T3= 27.1, T4= 28.1 deg C
10:39 - 24 V power supply no. 1 is enabled with a current of 62.200 A.
10:39 - Starting NMC
10:39 - Clearing PPS error counters
10:39 - Starting task "Check high voltages"
10:39 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190111/NectarCAM.6newFPMv2.NMC.xml
10:39 - Done
10:39 - Found 6 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:39 - Low voltages range between 100.00 V and 100.00 V. 
10:39 - Reference voltages range between 939.00 V and 1085.00 V. 
10:39 - Actual voltage is between 938.79 V and 1085.19 V.
10:39 - Maximum difference between expected and actual voltages is 0.48 V
10:39 - Maximum of current limits is 4925.14 uA
10:39 - Checking status of HVPA module in 6 drawer(s)...
10:39 - Checking status of HVPA channels in 6 drawer(s)...
10:39 - HV is stabilized in all channels.
10:39 - Finished task "Check high voltages"
10:39 - Status: TibState.RunStopped
10:39 - Alarms: AlarmVector.NoAlarm
10:39 - Connection status: False
10:39 - External delays: Local=3825.000 ns, Calibration=3825.000 ns, Sphe=3825.000 ns
10:39 - Trigger mask: 0x51 = TriggerMask.SlowControl|Software|Mono
10:39 - Input mask: 0x7
10:39 - Disable BUSY: False
10:39 - Extra BUSY Delay: 0.0
10:39 - Temperature: 37.75
10:40 - Configuring UCTS
10:40 - Configuring TIB...
10:40 - Setting TIB forced mode to False
10:40 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:40 - Status: TibState.RunStopped
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: False
10:40 - Disabling PPS
10:40 - Status: TibState.PpsStopped
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: False
10:40 - Entering set_external_delay
10:40 - Setting ExternalDelayLocal to 0.000 ns
10:40 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:40 - Entering set_external_delay
10:40 - Setting ExternalDelayCalibration to 76.000 ns
10:40 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:40 - Entering set_external_delay
10:40 - Setting ExternalDelaySphe to 0.000 ns
10:40 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:40 - Setting TIB trigger mode to 0x60 = TriggerMask.SlowControl|Pedestal
10:40 - Writing 96 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:40 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:40 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:40 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:40 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:40 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:40 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:40 - Status: TibState.PpsStopped
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: False
10:40 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:40 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:40 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:40 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:40 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:40 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:40 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:40 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:40 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:40 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:40 - Connecting TIB to camera server at 10.10.4.12:222
10:40 - Starting TIB...
10:40 - Status: TibState.PpsStopped
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: False
10:40 - Resetting run
10:40 - Wait for UCTS external trigger before enabling trigger...
10:40 - Status: TibState.Standby
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: False
10:40 - Status: TibState.Standby
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: False
10:40 - Status: TibState.Armed
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: True
10:40 - Starting TIB triggers...
10:40 - Enabling trigger
10:40 - Status: TibState.Running
10:40 - Alarms: AlarmVector.NoAlarm
10:40 - Connection status: True
10:40 - Stopping TIB...
10:40 - Status: TibState.Running
10:40 - Alarms: AlarmVector.ReadError
10:40 - Connection status: True
10:40 - Disabling trigger
10:40 - Disabling PPS
10:41 - Status: TibState.PpsStopped
10:41 - Alarms: AlarmVector.ReadError
10:41 - Connection status: True
10:41 - Closing TIB connection to camera server
10:41 - Status: TibState.PpsStopped
10:41 - Alarms: AlarmVector.ReadError
10:41 - Connection status: False
10:41 - Run duration: 0:00:10
10:41 - Local camera triggers: 0
10:41 - Slow control triggers: 0
10:41 - Single photo-electron triggers: 0
10:41 - Calibration triggers: 0
10:41 - Software triggers from UCTS: 0
10:41 - Pedestal triggers: 9019
10:41 - Collected input triggers: 6121
10:41 - Busy triggers: 0
10:41 - Camera event triggers sent to clusters: 6121
10:41 - Stopping NMC
10:41 - Found 0 PPS errors.
10:41 - Starting task "Check high voltages"
10:41 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190111/NectarCAM.6newFPMv2.NMC.xml
10:41 - Done
10:41 - Found 6 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:41 - Low voltages range between 100.00 V and 100.00 V. 
10:41 - Reference voltages range between 939.00 V and 1085.00 V. 
10:41 - Actual voltage is between 938.79 V and 1085.19 V.
10:41 - Maximum difference between expected and actual voltages is 0.52 V
10:41 - Maximum of current limits is 4925.14 uA
10:41 - Checking status of HVPA module in 6 drawer(s)...
10:41 - Checking status of HVPA channels in 6 drawer(s)...
10:41 - HV is stabilized in all channels.
10:41 - Finished task "Check high voltages"