12:32 - ECC is in state EccState.Ready with status EccStatus.NoError
12:32 - ECC temperature sensors: T1= 24.4, T2= 23.5, T3= 25.1, T4= 26.0 deg C
12:32 - 24 V power supply no. 1 is enabled with a current of 56.800 A.
12:32 - Resetting TIB...
12:32 - Failed to call Reset: Bad statuses are present
12:32 - Starting task "Check high voltages"
12:32 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190109/config_11newFPMv2.NMC.xml
12:32 - Done
12:32 - Found 11 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
12:32 - Low voltages range between 100.00 V and 100.00 V. 
12:32 - Reference voltages range between 956.00 V and 1141.00 V. 
12:32 - Actual voltage is between 955.87 V and 1140.70 V.
12:32 - Maximum difference between expected and actual voltages is 0.64 V
12:32 - Maximum of current limits is 5231.05 uA
12:32 - Checking status of HVPA module in 11 drawer(s)...
12:32 - Checking status of HVPA channels in 11 drawer(s)...
12:32 - HV is stabilized in all channels.
12:32 - Finished task "Check high voltages"
12:32 - Starting NMC
12:32 - Clearing PPS error counters
12:32 - Configuring TIB...
12:32 - Setting TIB forced mode to False
12:32 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
12:32 - Status: TibState.RunStopped
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: False
12:32 - Disabling PPS
12:32 - Status: TibState.PpsStopped
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: False
12:32 - Entering set_external_delay
12:32 - Setting ExternalDelayLocal to 0.000 ns
12:32 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
12:32 - Entering set_external_delay
12:32 - Setting ExternalDelayCalibration to 76.000 ns
12:32 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
12:32 - Entering set_external_delay
12:32 - Setting ExternalDelaySphe to 0.000 ns
12:32 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
12:32 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
12:32 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
12:32 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
12:32 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
12:32 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
12:32 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
12:32 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
12:32 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
12:32 - Status: TibState.PpsStopped
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: False
12:32 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
12:32 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
12:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:32 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
12:32 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
12:32 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
12:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:32 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
12:32 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
12:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:32 - Connecting TIB to camera server at 10.10.4.12:222
12:32 - Starting TIB...
12:32 - Status: TibState.PpsStopped
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: False
12:32 - Resetting run
12:32 - Wait for UCTS external trigger before enabling trigger...
12:32 - Status: TibState.Standby
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: False
12:32 - Status: TibState.Standby
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: False
12:32 - Status: TibState.Armed
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: True
12:32 - Starting TIB triggers...
12:32 - Enabling trigger
12:32 - Status: TibState.Running
12:32 - Alarms: AlarmVector.NoAlarm
12:32 - Connection status: True
12:32 - Configuring calibration box...
12:32 - Configuring calibration box with leds=0x358 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=300 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
12:32 - Starting flashes...
12:33 - Stopping TIB...
12:33 - Status: TibState.Running
12:33 - Alarms: AlarmVector.ReadError
12:33 - Connection status: True
12:33 - Disabling trigger
12:33 - Disabling PPS
12:33 - Status: TibState.PpsStopped
12:33 - Alarms: AlarmVector.ReadError
12:33 - Connection status: True
12:33 - Closing TIB connection to camera server
12:33 - Status: TibState.PpsStopped
12:33 - Alarms: AlarmVector.ReadError
12:33 - Connection status: False
12:33 - Run duration: 0:01:00
12:33 - Local camera triggers: 0
12:33 - Slow control triggers: 0
12:33 - Single photo-electron triggers: 0
12:33 - Calibration triggers: 29936
12:33 - Software triggers from UCTS: 0
12:33 - Pedestal triggers: 0
12:33 - Collected input triggers: 29936
12:33 - Busy triggers: 0
12:33 - Camera event triggers sent to clusters: 29936
12:33 - Stopping NMC
12:33 - Found 0 PPS errors.
12:33 - Starting task "Check high voltages"
12:33 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190109/config_11newFPMv2.NMC.xml
12:33 - Done
12:33 - Found 11 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
12:33 - Low voltages range between 100.00 V and 100.00 V. 
12:33 - Reference voltages range between 956.00 V and 1141.00 V. 
12:33 - Actual voltage is between 955.87 V and 1140.70 V.
12:33 - Maximum difference between expected and actual voltages is 0.58 V
12:33 - Maximum of current limits is 5231.05 uA
12:33 - Checking status of HVPA module in 11 drawer(s)...
12:33 - Checking status of HVPA channels in 11 drawer(s)...
12:33 - HV is stabilized in all channels.
12:33 - Finished task "Check high voltages"