11:00 - ECC is in state EccState.Ready with status EccStatus.NoError
11:00 - ECC temperature sensors: T1= 26.5, T2= 25.7, T3= 27.2, T4= 28.3 deg C
11:00 - 24 V power supply no. 1 is enabled with a current of 59.600 A.
11:00 - Stopping NMC
11:00 - Found 0 PPS errors.
11:00 - Starting task "Check high voltages"
11:00 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190108/NectarCAM.Run1032.NMC.xml
11:00 - Done
11:00 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:00 - Low voltages range between 100.00 V and 100.00 V. 
11:00 - Reference voltages range between 943.80 V and 1198.89 V. 
11:01 - Actual voltage is between 943.67 V and 1199.26 V.
11:01 - Maximum difference between expected and actual voltages is 0.94 V
11:01 - Maximum of current limits is 5647.07 uA
11:01 - Checking status of HVPA module in 37 drawer(s)...
11:01 - Checking status of HVPA channels in 37 drawer(s)...
11:01 - HV is stabilized in all channels.
11:01 - Finished task "Check high voltages"
11:01 - Starting NMC
11:01 - Clearing PPS error counters
11:01 - Configuring TIB...
11:01 - Setting TIB forced mode to False
11:01 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:01 - Status: TibState.RunStopped
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: False
11:01 - Disabling PPS
11:01 - Status: TibState.PpsStopped
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: False
11:01 - Entering set_external_delay
11:01 - Setting ExternalDelayLocal to 0.000 ns
11:01 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:01 - Entering set_external_delay
11:01 - Setting ExternalDelayCalibration to 76.000 ns
11:01 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:01 - Entering set_external_delay
11:01 - Setting ExternalDelaySphe to 0.000 ns
11:01 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:01 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
11:01 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:01 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:01 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:01 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:01 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:01 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:01 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:01 - Status: TibState.PpsStopped
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: False
11:01 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:01 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:01 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:01 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:01 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:01 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:01 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:01 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:01 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:01 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:01 - Connecting TIB to camera server at 10.10.4.12:222
11:01 - Starting TIB...
11:01 - Status: TibState.PpsStopped
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: False
11:01 - Resetting run
11:01 - Wait for UCTS external trigger before enabling trigger...
11:01 - Status: TibState.Standby
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: False
11:01 - Status: TibState.Standby
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: False
11:01 - Status: TibState.Armed
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: True
11:01 - Starting TIB triggers...
11:01 - Enabling trigger
11:01 - Status: TibState.Running
11:01 - Alarms: AlarmVector.NoAlarm
11:01 - Connection status: True
11:01 - Configuring calibration box...
11:01 - Configuring calibration box with leds=0x40 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
11:01 - Scanning voltages
11:01 - Starting task "Scan voltages"
11:01 - Setting LED mask to 0x0
11:01 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
11:01 - Starting flashes...
11:01 - Stopping flashes...
11:02 - Setting LED mask to 0x40
11:02 - Setting voltage to 8.000000 V
11:02 - Starting flashes...
11:02 - Stopping flashes...
11:02 - Setting voltage to 8.250000 V
11:02 - Starting flashes...
11:02 - Stopping flashes...
11:02 - Setting voltage to 8.500000 V
11:02 - Starting flashes...
11:02 - Stopping flashes...
11:03 - Setting voltage to 8.750000 V
11:03 - Starting flashes...
11:03 - Stopping flashes...
11:03 - Setting voltage to 9.000000 V
11:03 - Starting flashes...
11:03 - Stopping flashes...
11:03 - Setting voltage to 9.250000 V
11:03 - Starting flashes...
11:03 - Stopping flashes...
11:04 - Setting voltage to 9.500000 V
11:04 - Starting flashes...
11:04 - Stopping flashes...
11:04 - Setting voltage to 9.750000 V
11:04 - Starting flashes...
11:04 - Stopping flashes...
11:04 - Setting voltage to 10.000000 V
11:04 - Starting flashes...
11:04 - Stopping flashes...
11:04 - Setting voltage to 10.250000 V
11:04 - Starting flashes...
11:05 - Stopping flashes...
11:05 - Setting voltage to 10.500000 V
11:05 - Starting flashes...
11:05 - Stopping flashes...
11:05 - Setting voltage to 10.750000 V
11:05 - Starting flashes...
11:05 - Stopping flashes...
11:05 - Setting voltage to 11.000000 V
11:05 - Starting flashes...
11:05 - Stopping flashes...
11:06 - Setting voltage to 11.250000 V
11:06 - Starting flashes...
11:06 - Stopping flashes...
11:06 - Setting voltage to 11.500000 V
11:06 - Starting flashes...
11:06 - Stopping flashes...
11:06 - Setting voltage to 11.750000 V
11:06 - Starting flashes...
11:06 - Stopping flashes...
11:07 - Setting voltage to 12.000000 V
11:07 - Starting flashes...
11:07 - Stopping flashes...
11:07 - Setting voltage to 12.250000 V
11:07 - Starting flashes...
11:07 - Stopping flashes...
11:07 - Setting voltage to 12.500000 V
11:07 - Starting flashes...
11:07 - Stopping flashes...
11:07 - Setting voltage to 12.750000 V
11:07 - Starting flashes...
11:08 - Stopping flashes...
11:08 - Setting voltage to 13.000000 V
11:08 - Starting flashes...
11:08 - Stopping flashes...
11:08 - Setting voltage to 13.250000 V
11:08 - Starting flashes...
11:08 - Stopping flashes...
11:08 - Setting voltage to 13.500000 V
11:08 - Starting flashes...
11:08 - Stopping flashes...
11:09 - Setting voltage to 13.750000 V
11:09 - Starting flashes...
11:09 - Stopping flashes...
11:09 - Setting voltage to 14.000000 V
11:09 - Starting flashes...
11:09 - Stopping flashes...
11:09 - Setting voltage to 14.250000 V
11:09 - Starting flashes...
11:09 - Stopping flashes...
11:10 - Setting voltage to 14.500000 V
11:10 - Starting flashes...
11:10 - Stopping flashes...
11:10 - Setting voltage to 14.750000 V
11:10 - Starting flashes...
11:10 - Stopping flashes...
11:10 - Setting voltage to 15.000000 V
11:10 - Starting flashes...
11:10 - Stopping flashes...
11:11 - Setting voltage to 15.250000 V
11:11 - Starting flashes...
11:11 - Stopping flashes...
11:11 - Setting voltage to 15.500000 V
11:11 - Starting flashes...
11:11 - Stopping flashes...
11:11 - Setting voltage to 15.750000 V
11:11 - Starting flashes...
11:11 - Stopping flashes...
11:11 - Setting voltage to 16.000000 V
11:11 - Starting flashes...
11:12 - Stopping flashes...
11:12 - Finished task "Scan voltages"
11:12 - Stopping TIB...
11:12 - Status: TibState.Running
11:12 - Alarms: AlarmVector.ReadError
11:12 - Connection status: True
11:12 - Disabling trigger
11:12 - Disabling PPS
11:12 - Status: TibState.PpsStopped
11:12 - Alarms: AlarmVector.ReadError
11:12 - Connection status: True
11:12 - Closing TIB connection to camera server
11:12 - Status: TibState.PpsStopped
11:12 - Alarms: AlarmVector.ReadError
11:12 - Connection status: False
11:12 - Run duration: 0:10:39
11:12 - Local camera triggers: 0
11:12 - Slow control triggers: 0
11:12 - Single photo-electron triggers: 0
11:12 - Calibration triggers: 20583
11:12 - Software triggers from UCTS: 0
11:12 - Pedestal triggers: 0
11:12 - Collected input triggers: 20583
11:12 - Busy triggers: 0
11:12 - Camera event triggers sent to clusters: 20583
11:12 - Stopping NMC
11:12 - Found 0 PPS errors.
11:12 - Starting task "Check high voltages"
11:12 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190108/NectarCAM.Run1032.NMC.xml
11:12 - Done
11:12 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:12 - Low voltages range between 100.00 V and 100.00 V. 
11:12 - Reference voltages range between 943.80 V and 1198.89 V. 
11:12 - Actual voltage is between 943.67 V and 1199.26 V.
11:12 - Maximum difference between expected and actual voltages is 0.72 V
11:12 - Maximum of current limits is 5647.07 uA
11:12 - Checking status of HVPA module in 37 drawer(s)...
11:12 - Checking status of HVPA channels in 37 drawer(s)...
11:12 - HV is stabilized in all channels.
11:12 - Finished task "Check high voltages"