17:19 - Starting task "Check high voltages"
17:19 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190103/NectarCAM.Run1026.NMC.xml
17:19 - Done
17:19 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:19 - Low voltages range between 100.00 V and 100.00 V. 
17:19 - Reference voltages range between 943.80 V and 1198.89 V. 
17:19 - Actual voltage is between 943.67 V and 1198.65 V.
17:19 - Maximum difference between expected and actual voltages is 0.74 V
17:19 - Maximum of current limits is 5647.07 uA
17:19 - Checking status of HVPA module in 37 drawer(s)...
17:19 - Checking status of HVPA channels in 37 drawer(s)...
17:19 - HV is stabilized in all channels.
17:19 - Finished task "Check high voltages"
17:19 - Starting NMC
17:19 - Clearing PPS error counters
17:19 - Configuring TIB...
17:19 - Setting TIB forced mode to False
17:19 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
17:19 - Status: TibState.PpsStopped
17:19 - Alarms: AlarmVector.ReadError
17:19 - Connection status: False
17:19 - Entering set_external_delay
17:19 - Setting ExternalDelayLocal to 0.000 ns
17:19 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
17:19 - Entering set_external_delay
17:19 - Setting ExternalDelayCalibration to 76.000 ns
17:19 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
17:19 - Entering set_external_delay
17:19 - Setting ExternalDelaySphe to 0.000 ns
17:19 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
17:19 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
17:19 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
17:19 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
17:19 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
17:19 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
17:19 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
17:19 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
17:19 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
17:19 - Status: TibState.PpsStopped
17:19 - Alarms: AlarmVector.ReadError
17:19 - Connection status: False
17:19 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
17:19 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
17:19 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:19 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
17:19 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
17:19 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
17:19 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:19 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
17:19 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
17:19 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:19 - Connecting TIB to camera server at 10.10.4.12:222
17:19 - Starting TIB...
17:19 - Status: TibState.PpsStopped
17:19 - Alarms: AlarmVector.ReadError
17:19 - Connection status: False
17:19 - Resetting run
17:19 - Wait for UCTS external trigger before enabling trigger...
17:19 - Status: TibState.Standby
17:19 - Alarms: AlarmVector.NoAlarm
17:19 - Connection status: False
17:19 - Status: TibState.Standby
17:19 - Alarms: AlarmVector.NoAlarm
17:19 - Connection status: False
17:20 - Status: TibState.Armed
17:20 - Alarms: AlarmVector.NoAlarm
17:20 - Connection status: True
17:20 - Starting TIB triggers...
17:20 - Enabling trigger
17:20 - Status: TibState.Running
17:20 - Alarms: AlarmVector.NoAlarm
17:20 - Connection status: True
17:20 - Configuring calibration box...
17:20 - Configuring calibration box with leds=0x1fff voltage=12.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
17:20 - Scanning voltages
17:20 - Starting task "Scan voltages"
17:20 - Setting LED mask to 0x0
17:20 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
17:20 - Starting flashes...
17:20 - Stopping flashes...
17:20 - Setting LED mask to 0x1fff
17:20 - Setting voltage to 8.000000 V
17:20 - Starting flashes...
17:20 - Stopping flashes...
17:20 - Setting voltage to 8.250000 V
17:20 - Starting flashes...
17:20 - Stopping flashes...
17:21 - Setting voltage to 8.500000 V
17:21 - Starting flashes...
17:21 - Stopping flashes...
17:21 - Setting voltage to 8.750000 V
17:21 - Starting flashes...
17:21 - Stopping flashes...
17:21 - Setting voltage to 9.000000 V
17:21 - Starting flashes...
17:21 - Stopping flashes...
17:21 - Setting voltage to 9.250000 V
17:21 - Starting flashes...
17:22 - Stopping flashes...
17:22 - Setting voltage to 9.500000 V
17:22 - Starting flashes...
17:22 - Stopping flashes...
17:22 - Setting voltage to 9.750000 V
17:22 - Starting flashes...
17:22 - Stopping flashes...
17:22 - Setting voltage to 10.000000 V
17:22 - Starting flashes...
17:22 - Stopping flashes...
17:23 - Setting voltage to 10.250000 V
17:23 - Starting flashes...
17:23 - Stopping flashes...
17:23 - Setting voltage to 10.500000 V
17:23 - Starting flashes...
17:23 - Stopping flashes...
17:23 - Setting voltage to 10.750000 V
17:23 - Starting flashes...
17:23 - Stopping flashes...
17:24 - Setting voltage to 11.000000 V
17:24 - Starting flashes...
17:24 - Stopping flashes...
17:24 - Setting voltage to 11.250000 V
17:24 - Starting flashes...
17:24 - Stopping flashes...
17:24 - Setting voltage to 11.500000 V
17:24 - Starting flashes...
17:24 - Stopping flashes...
17:24 - Setting voltage to 11.750000 V
17:24 - Starting flashes...
17:25 - Stopping flashes...
17:25 - Setting voltage to 12.000000 V
17:25 - Starting flashes...
17:25 - Stopping flashes...
17:25 - Setting voltage to 12.250000 V
17:25 - Starting flashes...
17:25 - Stopping flashes...
17:25 - Setting voltage to 12.500000 V
17:25 - Starting flashes...
17:25 - Stopping flashes...
17:26 - Setting voltage to 12.750000 V
17:26 - Starting flashes...
17:26 - Stopping flashes...
17:26 - Setting voltage to 13.000000 V
17:26 - Starting flashes...
17:26 - Stopping flashes...
17:26 - Setting voltage to 13.250000 V
17:26 - Starting flashes...
17:26 - Stopping flashes...
17:27 - Setting voltage to 13.500000 V
17:27 - Starting flashes...
17:27 - Stopping flashes...
17:27 - Setting voltage to 13.750000 V
17:27 - Starting flashes...
17:27 - Stopping flashes...
17:27 - Setting voltage to 14.000000 V
17:27 - Starting flashes...
17:27 - Stopping flashes...
17:28 - Setting voltage to 14.250000 V
17:28 - Starting flashes...
17:28 - Stopping flashes...
17:28 - Setting voltage to 14.500000 V
17:28 - Starting flashes...
17:28 - Stopping flashes...
17:28 - Setting voltage to 14.750000 V
17:28 - Starting flashes...
17:28 - Stopping flashes...
17:28 - Setting voltage to 15.000000 V
17:28 - Starting flashes...
17:29 - Stopping flashes...
17:29 - Setting voltage to 15.250000 V
17:29 - Starting flashes...
17:29 - Stopping flashes...
17:29 - Setting voltage to 15.500000 V
17:29 - Starting flashes...
17:29 - Stopping flashes...
17:29 - Setting voltage to 15.750000 V
17:29 - Starting flashes...
17:29 - Stopping flashes...
17:30 - Setting voltage to 16.000000 V
17:30 - Starting flashes...
17:30 - Stopping flashes...
17:30 - Finished task "Scan voltages"
17:37 - Stopping TIB...
17:37 - Status: TibState.Running
17:37 - Alarms: AlarmVector.ReadError
17:37 - Connection status: True
17:37 - Disabling trigger
17:37 - Disabling PPS
17:37 - Status: TibState.PpsStopped
17:37 - Alarms: AlarmVector.ReadError
17:37 - Connection status: True
17:37 - Closing TIB connection to camera server
17:37 - Status: TibState.PpsStopped
17:37 - Alarms: AlarmVector.ReadError
17:37 - Connection status: False
17:37 - Run duration: 0:17:40
17:37 - Local camera triggers: 0
17:37 - Slow control triggers: 0
17:37 - Single photo-electron triggers: 0
17:37 - Calibration triggers: 20584
17:37 - Software triggers from UCTS: 0
17:37 - Pedestal triggers: 0
17:37 - Collected input triggers: 20584
17:37 - Busy triggers: 0
17:37 - Camera event triggers sent to clusters: 20584
17:37 - Stopping NMC
17:37 - Found 0 PPS errors.
17:38 - Starting task "Check high voltages"
17:38 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190103/NectarCAM.Run1026.NMC.xml
17:38 - Done
17:38 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:38 - Low voltages range between 100.00 V and 100.00 V. 
17:38 - Reference voltages range between 943.80 V and 1198.89 V.