16:18 - Resetting TIB...
16:18 - Failed to call Reset: Bad statuses are present
16:18 - ECC is in state EccState.Ready with status EccStatus.NoError
16:18 - ECC temperature sensors: T1= 24.8, T2= 24.1, T3= 25.5, T4= 26.0 deg C
16:18 - 24 V power supply no. 1 is enabled with a current of 59.900 A.
16:18 - Starting task "Check high voltages"
16:18 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190103/NectarCAM.Run1026.NMC.xml
16:18 - Done
16:18 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:18 - Low voltages range between 100.00 V and 100.00 V. 
16:18 - Reference voltages range between 943.80 V and 1198.89 V. 
16:18 - Actual voltage is between 943.67 V and 1199.26 V.
16:18 - Maximum difference between expected and actual voltages is 0.72 V
16:18 - Maximum of current limits is 5647.07 uA
16:18 - Checking status of HVPA module in 37 drawer(s)...
16:18 - Checking status of HVPA channels in 37 drawer(s)...
16:18 - HV is stabilized in all channels.
16:18 - Finished task "Check high voltages"
16:20 - Starting NMC
16:20 - Clearing PPS error counters
16:20 - Configuring TIB...
16:20 - Setting TIB forced mode to False
16:20 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:20 - Status: TibState.RunStopped
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: False
16:20 - Disabling PPS
16:20 - Status: TibState.PpsStopped
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: False
16:20 - Entering set_external_delay
16:20 - Setting ExternalDelayLocal to 0.000 ns
16:20 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:20 - Entering set_external_delay
16:20 - Setting ExternalDelayCalibration to 76.000 ns
16:20 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:20 - Entering set_external_delay
16:20 - Setting ExternalDelaySphe to 0.000 ns
16:20 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:20 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
16:20 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:20 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:20 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:20 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:20 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:20 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:20 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:20 - Status: TibState.PpsStopped
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: False
16:20 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:20 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:20 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:20 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:20 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:20 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:20 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:20 - Connecting TIB to camera server at 10.10.4.12:222
16:20 - Starting TIB...
16:20 - Status: TibState.PpsStopped
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: False
16:20 - Resetting run
16:20 - Wait for UCTS external trigger before enabling trigger...
16:20 - Status: TibState.Standby
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: False
16:20 - Status: TibState.Standby
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: False
16:20 - Status: TibState.Armed
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: True
16:20 - Starting TIB triggers...
16:20 - Enabling trigger
16:20 - Status: TibState.Running
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Connection status: True
16:20 - Status: TibState.Running ConnectionStatus: True
16:20 - Alarms: AlarmVector.NoAlarm
16:20 - Temperature: 37.12
16:20 - Local camera rate: 0.0 Hz
16:20 - Stereo trigger rate: 0.0 Hz
16:20 - SPE trigger rate: 0.0 Hz
16:20 - Calibration trigger rate: 0.0 Hz
16:20 - Software trigger rate: 0.0 Hz
16:20 - Pedestal trigger rate: 0.0 Hz
16:20 - Collected trigger rate: 0.0 Hz
16:20 - Busy rate: 0.0 Hz
16:20 - Camera trigger rate: 0.0 Hz
16:20 - Configuring calibration box...
16:20 - Configuring calibration box with leds=0x40 voltage=12.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
16:20 - Scanning voltages
16:20 - Starting task "Scan voltages"
16:20 - Setting LED mask to 0x0
16:20 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
16:20 - Starting flashes...
16:21 - Stopping flashes...
16:21 - Setting LED mask to 0x40
16:21 - Setting voltage to 8.000000 V
16:21 - Starting flashes...
16:21 - Stopping flashes...
16:21 - Setting voltage to 8.250000 V
16:21 - Starting flashes...
16:21 - Stopping flashes...
16:21 - Setting voltage to 8.500000 V
16:21 - Starting flashes...
16:22 - Stopping flashes...
16:22 - Setting voltage to 8.750000 V
16:22 - Starting flashes...
16:22 - Stopping flashes...
16:22 - Setting voltage to 9.000000 V
16:22 - Starting flashes...
16:22 - Stopping flashes...
16:22 - Setting voltage to 9.250000 V
16:22 - Starting flashes...
16:22 - Stopping flashes...
16:23 - Setting voltage to 9.500000 V
16:23 - Starting flashes...
16:23 - Stopping flashes...
16:23 - Setting voltage to 9.750000 V
16:23 - Starting flashes...
16:23 - Stopping flashes...
16:23 - Setting voltage to 10.000000 V
16:23 - Starting flashes...
16:23 - Stopping flashes...
16:24 - Setting voltage to 10.250000 V
16:24 - Starting flashes...
16:24 - Stopping flashes...
16:24 - Setting voltage to 10.500000 V
16:24 - Starting flashes...
16:24 - Stopping flashes...
16:24 - Setting voltage to 10.750000 V
16:24 - Starting flashes...
16:24 - Stopping flashes...
16:24 - Setting voltage to 11.000000 V
16:24 - Starting flashes...
16:25 - Stopping flashes...
16:25 - Setting voltage to 11.250000 V
16:25 - Starting flashes...
16:25 - Stopping flashes...
16:25 - Setting voltage to 11.500000 V
16:25 - Starting flashes...
16:25 - Stopping flashes...
16:25 - Setting voltage to 11.750000 V
16:25 - Starting flashes...
16:25 - Stopping flashes...
16:26 - Setting voltage to 12.000000 V
16:26 - Starting flashes...
16:26 - Stopping flashes...
16:26 - Setting voltage to 12.250000 V
16:26 - Starting flashes...
16:26 - Stopping flashes...
16:26 - Setting voltage to 12.500000 V
16:26 - Starting flashes...
16:26 - Stopping flashes...
16:27 - Setting voltage to 12.750000 V
16:27 - Starting flashes...
16:27 - Stopping flashes...
16:27 - Setting voltage to 13.000000 V
16:27 - Starting flashes...
16:27 - Stopping flashes...
16:27 - Setting voltage to 13.250000 V
16:27 - Starting flashes...
16:27 - Stopping flashes...
16:27 - Setting voltage to 13.500000 V
16:27 - Starting flashes...
16:28 - Stopping flashes...
16:28 - Setting voltage to 13.750000 V
16:28 - Starting flashes...
16:28 - Stopping flashes...
16:28 - Setting voltage to 14.000000 V
16:28 - Starting flashes...
16:28 - Stopping flashes...
16:28 - Setting voltage to 14.250000 V
16:28 - Starting flashes...
16:28 - Stopping flashes...
16:29 - Setting voltage to 14.500000 V
16:29 - Starting flashes...
16:29 - Stopping flashes...
16:29 - Setting voltage to 14.750000 V
16:29 - Starting flashes...
16:29 - Stopping flashes...
16:29 - Setting voltage to 15.000000 V
16:29 - Starting flashes...
16:29 - Stopping flashes...
16:30 - Setting voltage to 15.250000 V
16:30 - Starting flashes...
16:30 - Stopping flashes...
16:30 - Setting voltage to 15.500000 V
16:30 - Starting flashes...
16:30 - Stopping flashes...
16:30 - Setting voltage to 15.750000 V
16:30 - Starting flashes...
16:30 - Stopping flashes...
16:30 - Setting voltage to 16.000000 V
16:31 - Starting flashes...
16:31 - Stopping flashes...
16:31 - Finished task "Scan voltages"
16:51 - Stopping TIB...
16:51 - Status: TibState.Running
16:51 - Alarms: AlarmVector.ReadError
16:51 - Connection status: True
16:51 - Disabling trigger
16:51 - Disabling PPS
16:51 - Status: TibState.PpsStopped
16:51 - Alarms: AlarmVector.ReadError
16:51 - Connection status: True
16:51 - Closing TIB connection to camera server
16:52 - Status: TibState.PpsStopped
16:52 - Alarms: AlarmVector.ReadError
16:52 - Connection status: False
16:52 - Run duration: 0:31:22
16:52 - Local camera triggers: 0
16:52 - Slow control triggers: 0
16:52 - Single photo-electron triggers: 0
16:52 - Calibration triggers: 20584
16:52 - Software triggers from UCTS: 0
16:52 - Pedestal triggers: 0
16:52 - Collected input triggers: 20584
16:52 - Busy triggers: 0
16:52 - Camera event triggers sent to clusters: 20584
16:52 - Stopping NMC
16:52 - Found 0 PPS errors.
16:52 - Starting task "Check high voltages"
16:52 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190103/NectarCAM.Run1026.NMC.xml
16:52 - Done
16:52 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:52 - Low voltages range between 100.00 V and 100.00 V. 
16:52 - Reference voltages range between 943.80 V and 1198.89 V. 
16:52 - Actual voltage is between 943.67 V and 1198.65 V.
16:52 - Maximum difference between expected and actual voltages is 0.71 V
16:52 - Maximum of current limits is 5647.07 uA
16:52 - Checking status of HVPA module in 37 drawer(s)...
16:52 - Checking status of HVPA channels in 37 drawer(s)...
16:52 - HV is stabilized in all channels.
16:52 - Finished task "Check high voltages"