16:04 - ECC is in state EccState.Ready with status EccStatus.NoError
16:04 - ECC temperature sensors: T1= 24.8, T2= 24.1, T3= 25.6, T4= 26.3 deg C
16:04 - 24 V power supply no. 1 is enabled with a current of 39.700 A.
16:04 - Stopping NMC
16:04 - Found 0 PPS errors.
16:04 - Checking high voltages...
16:04 - Starting task "Check HV"
16:04 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181205/NectarCAM.Run1013.NMC.xml
16:04 - Done
16:04 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:05 - Found 37 drawer(s). Reference voltage is between 938.66 V and 1181.59 V. Actual voltage is between 938.18 V and 1181.57 V.
16:05 - Maximum difference between expected and actual voltages in drawer 76 is 0.35 V
16:05 - Maximum difference between expected and actual voltages in drawer 77 is 0.63 V
16:05 - Maximum difference between expected and actual voltages in drawer 78 is 0.47 V
16:05 - Maximum difference between expected and actual voltages in drawer 79 is 0.69 V
16:05 - Maximum difference between expected and actual voltages in drawer 80 is 0.28 V
16:05 - Maximum difference between expected and actual voltages in drawer 81 is 0.38 V
16:05 - Maximum difference between expected and actual voltages in drawer 93 is 0.73 V
16:05 - Maximum difference between expected and actual voltages in drawer 94 is 0.63 V
16:05 - Maximum difference between expected and actual voltages in drawer 95 is 0.35 V
16:05 - Maximum difference between expected and actual voltages in drawer 96 is 0.38 V
16:05 - Maximum difference between expected and actual voltages in drawer 97 is 3.60 V
16:05 - Maximum difference between expected and actual voltages in drawer 98 is 0.64 V
16:05 - Maximum difference between expected and actual voltages in drawer 110 is 0.47 V
16:05 - Maximum difference between expected and actual voltages in drawer 111 is 0.41 V
16:05 - Maximum difference between expected and actual voltages in drawer 112 is 0.70 V
16:05 - Maximum difference between expected and actual voltages in drawer 113 is 0.47 V
16:05 - Maximum difference between expected and actual voltages in drawer 114 is 0.50 V
16:05 - Maximum difference between expected and actual voltages in drawer 115 is 0.46 V
16:05 - Maximum difference between expected and actual voltages in drawer 116 is 0.49 V
16:05 - Maximum difference between expected and actual voltages in drawer 128 is 0.52 V
16:05 - Maximum difference between expected and actual voltages in drawer 129 is 0.45 V
16:05 - Maximum difference between expected and actual voltages in drawer 130 is 0.68 V
16:05 - Maximum difference between expected and actual voltages in drawer 131 is 0.37 V
16:05 - Maximum difference between expected and actual voltages in drawer 132 is 0.46 V
16:05 - Maximum difference between expected and actual voltages in drawer 133 is 0.66 V
16:05 - Maximum difference between expected and actual voltages in drawer 145 is 0.46 V
16:05 - Maximum difference between expected and actual voltages in drawer 146 is 0.47 V
16:05 - Maximum difference between expected and actual voltages in drawer 147 is 0.61 V
16:05 - Maximum difference between expected and actual voltages in drawer 148 is 0.44 V
16:05 - Maximum difference between expected and actual voltages in drawer 149 is 0.29 V
16:05 - Maximum difference between expected and actual voltages in drawer 150 is 0.44 V
16:05 - Maximum difference between expected and actual voltages in drawer 163 is 0.69 V
16:05 - Maximum difference between expected and actual voltages in drawer 164 is 0.46 V
16:05 - Maximum difference between expected and actual voltages in drawer 165 is 0.46 V
16:05 - Maximum difference between expected and actual voltages in drawer 166 is 0.61 V
16:05 - Maximum difference between expected and actual voltages in drawer 167 is 0.48 V
16:05 - Maximum difference between expected and actual voltages in drawer 168 is 0.44 V
16:05 - Checking status of HVPA module in 37 drawer(s)...
16:05 - Checking status of HVPA channels in 37 drawer(s)...
16:05 - HV is stabilized in all channels.
16:05 - Finished task "Check HV"
16:05 - Starting NMC
16:05 - Clearing PPS error counters
16:05 - Configuring TIB...
16:05 - Setting TIB forced mode to False
16:05 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:05 - Status: TibState.RunStopped
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: False
16:05 - Disabling PPS
16:05 - Status: TibState.PpsStopped
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: False
16:05 - Entering set_external_delay
16:05 - Setting ExternalDelayLocal to 0.000 ns
16:05 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:05 - Entering set_external_delay
16:05 - Setting ExternalDelayCalibration to 76.000 ns
16:05 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:05 - Entering set_external_delay
16:05 - Setting ExternalDelaySphe to 0.000 ns
16:05 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:05 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
16:05 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:05 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:05 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:05 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:05 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:05 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:05 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:05 - Status: TibState.PpsStopped
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: False
16:05 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:05 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:05 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:05 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:05 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:05 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:05 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:05 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:05 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:05 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:05 - Connecting TIB to camera server at 10.10.4.12:222
16:05 - Starting TIB...
16:05 - Status: TibState.PpsStopped
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: False
16:05 - Resetting run
16:05 - Wait for UCTS external trigger before enabling trigger...
16:05 - Status: TibState.Standby
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: False
16:05 - Status: TibState.Standby
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: False
16:05 - Status: TibState.Armed
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: True
16:05 - Starting TIB triggers...
16:05 - Enabling trigger
16:05 - Status: TibState.Running
16:05 - Alarms: AlarmVector.NoAlarm
16:05 - Connection status: True
16:05 - Configuring calibration box...
16:05 - Configuring calibration box with leds=0x40 voltage=12.00 frequency=1000.0/1 central_current=0.0 duration=300 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
16:05 - Starting flashes...
16:06 - Stopping TIB...
16:06 - Status: TibState.Running
16:06 - Alarms: AlarmVector.ReadError
16:06 - Connection status: True
16:06 - Disabling trigger
16:06 - Disabling PPS
16:06 - Status: TibState.PpsStopped
16:06 - Alarms: AlarmVector.ReadError
16:06 - Connection status: True
16:06 - Closing TIB connection to camera server
16:06 - Status: TibState.PpsStopped
16:06 - Alarms: AlarmVector.ReadError
16:06 - Connection status: False
16:06 - Run duration: 0:00:44
16:06 - Local camera triggers: 0
16:06 - Slow control triggers: 0
16:06 - Single photo-electron triggers: 0
16:06 - Calibration triggers: 29964
16:06 - Software triggers from UCTS: 0
16:06 - Pedestal triggers: 43869
16:06 - Collected input triggers: 29964
16:06 - Busy triggers: 0
16:06 - Camera event triggers sent to clusters: 29964
16:06 - Stopping NMC
16:06 - Found 0 PPS errors.