18:09 - ECC is in state EccState.Ready with status EccStatus.NoError
18:09 - ECC temperature sensors: T1= 25.2, T2= 24.4, T3= 26.0, T4= 27.0 deg C
18:09 - 24 V power supply no. 1 is enabled with a current of 39.800 A.
18:09 - Checking high voltages...
18:09 - Starting task "Check HV"
18:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181204/NectarCAM.Run1010.NMC.xml
18:10 - Done
18:10 - Found 37 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
18:10 - Found 37 drawer(s). Reference voltage is between 938.66 V and 1200.00 V. Actual voltage is between 938.18 V and 1200.48 V.
18:10 - Maximum difference between expected and actual voltages in drawer 76 is 0.71 V
18:10 - Maximum difference between expected and actual voltages in drawer 77 is 0.39 V
18:10 - Maximum difference between expected and actual voltages in drawer 78 is 0.47 V
18:10 - Maximum difference between expected and actual voltages in drawer 79 is 0.48 V
18:10 - Maximum difference between expected and actual voltages in drawer 80 is 0.42 V
18:10 - Maximum difference between expected and actual voltages in drawer 81 is 0.50 V
18:10 - Maximum difference between expected and actual voltages in drawer 93 is 0.43 V
18:10 - Maximum difference between expected and actual voltages in drawer 94 is 0.44 V
18:10 - Maximum difference between expected and actual voltages in drawer 95 is 0.63 V
18:10 - Maximum difference between expected and actual voltages in drawer 96 is 0.44 V
18:10 - Maximum difference between expected and actual voltages in drawer 97 is 0.40 V
18:10 - Maximum difference between expected and actual voltages in drawer 98 is 0.33 V
18:10 - Maximum difference between expected and actual voltages in drawer 110 is 0.47 V
18:10 - Maximum difference between expected and actual voltages in drawer 111 is 0.97 V
18:10 - Maximum difference between expected and actual voltages in drawer 112 is 0.49 V
18:10 - Maximum difference between expected and actual voltages in drawer 113 is 0.43 V
18:10 - Maximum difference between expected and actual voltages in drawer 114 is 0.45 V
18:10 - Maximum difference between expected and actual voltages in drawer 115 is 0.49 V
18:10 - Maximum difference between expected and actual voltages in drawer 116 is 0.43 V
18:10 - Maximum difference between expected and actual voltages in drawer 128 is 0.47 V
18:10 - Maximum difference between expected and actual voltages in drawer 129 is 0.46 V
18:10 - Maximum difference between expected and actual voltages in drawer 130 is 0.40 V
18:10 - Maximum difference between expected and actual voltages in drawer 131 is 0.44 V
18:10 - Maximum difference between expected and actual voltages in drawer 132 is 0.60 V
18:10 - Maximum difference between expected and actual voltages in drawer 133 is 0.42 V
18:10 - Maximum difference between expected and actual voltages in drawer 145 is 0.45 V
18:10 - Maximum difference between expected and actual voltages in drawer 146 is 0.49 V
18:10 - Maximum difference between expected and actual voltages in drawer 147 is 0.64 V
18:10 - Maximum difference between expected and actual voltages in drawer 148 is 0.44 V
18:10 - Maximum difference between expected and actual voltages in drawer 149 is 0.31 V
18:10 - Maximum difference between expected and actual voltages in drawer 150 is 0.44 V
18:10 - Maximum difference between expected and actual voltages in drawer 163 is 0.59 V
18:10 - Maximum difference between expected and actual voltages in drawer 164 is 0.46 V
18:10 - Maximum difference between expected and actual voltages in drawer 165 is 0.42 V
18:10 - Maximum difference between expected and actual voltages in drawer 166 is 0.47 V
18:10 - Maximum difference between expected and actual voltages in drawer 167 is 0.48 V
18:10 - Maximum difference between expected and actual voltages in drawer 168 is 0.52 V
18:10 - Checking status of HVPA module in 37 drawer(s)...
18:10 - Checking status of HVPA channels in 37 drawer(s)...
18:10 - Starting NMC
18:10 - Clearing PPS error counters
18:10 - HV is stabilized in all channels.
18:10 - Finished task "Check HV"
18:10 - Configuring TIB...
18:10 - Setting TIB forced mode to False
18:10 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
18:10 - Status: TibState.PpsStopped
18:10 - Alarms: AlarmVector.ReadError
18:10 - Connection status: False
18:10 - Entering set_external_delay
18:10 - Setting ExternalDelayLocal to 0.000 ns
18:10 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
18:10 - Entering set_external_delay
18:10 - Setting ExternalDelayCalibration to 76.000 ns
18:10 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
18:10 - Entering set_external_delay
18:10 - Setting ExternalDelaySphe to 0.000 ns
18:10 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
18:10 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
18:10 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
18:10 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
18:10 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
18:10 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
18:10 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
18:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
18:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
18:10 - Status: TibState.PpsStopped
18:10 - Alarms: AlarmVector.ReadError
18:10 - Connection status: False
18:10 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
18:10 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
18:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:10 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
18:10 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
18:10 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
18:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:10 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
18:10 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
18:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
18:10 - Connecting TIB to camera server at 10.10.4.12:222
18:10 - Starting TIB...
18:10 - Status: TibState.PpsStopped
18:10 - Alarms: AlarmVector.ReadError
18:10 - Connection status: False
18:10 - Resetting run
18:10 - Wait for UCTS external trigger before enabling trigger...
18:10 - Status: TibState.Standby
18:10 - Alarms: AlarmVector.NoAlarm
18:10 - Connection status: False
18:10 - Status: TibState.Standby
18:10 - Alarms: AlarmVector.NoAlarm
18:10 - Connection status: False
18:10 - Status: TibState.Armed
18:10 - Alarms: AlarmVector.NoAlarm
18:10 - Connection status: True
18:10 - Starting TIB triggers...
18:10 - Enabling trigger
18:10 - Status: TibState.Running
18:10 - Alarms: AlarmVector.NoAlarm
18:10 - Connection status: True
18:10 - Configuring calibration box...
18:10 - Configuring calibration box with leds=0x40 voltage=12.00 frequency=1000.0/1 central_current=0.0 duration=300 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
18:10 - Starting flashes...
18:11 - Stopping TIB...
18:11 - Status: TibState.Running
18:11 - Alarms: AlarmVector.ReadError
18:11 - Connection status: True
18:11 - Disabling trigger
18:11 - Disabling PPS
18:11 - Status: TibState.PpsStopped
18:11 - Alarms: AlarmVector.ReadError
18:11 - Connection status: True
18:11 - Closing TIB connection to camera server
18:11 - Status: TibState.PpsStopped
18:11 - Alarms: AlarmVector.ReadError
18:11 - Connection status: False
18:11 - Run duration: 0:00:40
18:11 - Local camera triggers: 0
18:11 - Slow control triggers: 0
18:11 - Single photo-electron triggers: 0
18:11 - Calibration triggers: 29920
18:11 - Software triggers from UCTS: 0
18:11 - Pedestal triggers: 0
18:11 - Collected input triggers: 29920
18:11 - Busy triggers: 0
18:11 - Camera event triggers sent to clusters: 29920
18:11 - Stopping NMC
18:11 - Found 0 PPS errors.