10:38 - ECC is in state EccState.Ready with status EccStatus.NoError
10:38 - ECC temperature sensors: T1= 24.8, T2= 24.2, T3= 25.4, T4= 26.4 deg C
10:38 - 24 V power supply no. 1 is enabled with a current of 8.770 A.
10:38 - Stopping NMC
10:38 - Found 0 PPS errors.
10:38 - Checking high voltages...
10:38 - Starting task "Check HV"
10:38 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181116/config_11modules_HVnom.NMC.xml
10:38 - Done
10:38 - Found 11 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:38 - Found 11 drawer(s). Reference voltage is between 979.98 V and 1182.43 V. Actual voltage is between 980.27 V and 1182.79 V.
10:38 - Maximum difference between expected and actual voltages in drawer 76 is 0.59 V
10:38 - Maximum difference between expected and actual voltages in drawer 77 is 0.41 V
10:38 - Maximum difference between expected and actual voltages in drawer 93 is 0.37 V
10:38 - Maximum difference between expected and actual voltages in drawer 94 is 0.59 V
10:38 - Maximum difference between expected and actual voltages in drawer 110 is 0.21 V
10:38 - Maximum difference between expected and actual voltages in drawer 111 is 0.44 V
10:38 - Maximum difference between expected and actual voltages in drawer 112 is 0.49 V
10:38 - Maximum difference between expected and actual voltages in drawer 128 is 0.59 V
10:38 - Maximum difference between expected and actual voltages in drawer 129 is 0.56 V
10:38 - Maximum difference between expected and actual voltages in drawer 145 is 0.68 V
10:38 - Maximum difference between expected and actual voltages in drawer 146 is 0.46 V
10:38 - Checking status of HVPA module in 11 drawer(s)...
10:38 - Checking status of HVPA channels in 11 drawer(s)...
10:38 - HV is stabilized in all channels.
10:38 - Finished task "Check HV"
10:38 - Starting NMC
10:38 - Clearing PPS error counters
10:38 - Configuring TIB...
10:38 - Setting TIB forced mode to False
10:38 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:38 - Status: TibState.PpsStopped
10:38 - Alarms: AlarmVector.ReadError
10:38 - Connection status: False
10:38 - Entering set_external_delay
10:38 - Setting ExternalDelayLocal to 0.000 ns
10:38 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:38 - Entering set_external_delay
10:38 - Setting ExternalDelayCalibration to 76.000 ns
10:38 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:38 - Entering set_external_delay
10:38 - Setting ExternalDelaySphe to 0.000 ns
10:38 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:38 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
10:38 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:38 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:38 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:38 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:38 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:38 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:38 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:38 - Status: TibState.PpsStopped
10:38 - Alarms: AlarmVector.ReadError
10:38 - Connection status: False
10:38 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:38 - Writing 10000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:38 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:38 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:38 - Writing 10000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:38 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:38 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:38 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:38 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:38 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:38 - Connecting TIB to camera server at 10.10.4.12:222
10:38 - Starting TIB...
10:38 - Status: TibState.PpsStopped
10:38 - Alarms: AlarmVector.ReadError
10:38 - Connection status: False
10:38 - Resetting run
10:38 - Wait for UCTS external trigger before enabling trigger...
10:38 - Status: TibState.Standby
10:38 - Alarms: AlarmVector.NoAlarm
10:38 - Connection status: False
10:38 - Status: TibState.Standby
10:38 - Alarms: AlarmVector.NoAlarm
10:38 - Connection status: False
10:38 - Status: TibState.Armed
10:38 - Alarms: AlarmVector.NoAlarm
10:38 - Connection status: True
10:38 - Starting TIB triggers...
10:38 - Enabling trigger
10:38 - Status: TibState.Running
10:38 - Alarms: AlarmVector.NoAlarm
10:38 - Connection status: True
10:39 - Configuring calibration box...
10:39 - Configuring calibration box with leds=0x40 voltage=12.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
10:39 - Scanning voltages
10:39 - Starting task "Scan voltages"
10:39 - Setting LED mask to 0x0
10:39 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
10:39 - Starting flashes...
10:39 - Stopping flashes...
10:39 - Setting LED mask to 0x40
10:39 - Setting voltage to 8.000000 V
10:39 - Starting flashes...
10:39 - Stopping flashes...
10:39 - Setting voltage to 8.250000 V
10:39 - Starting flashes...
10:39 - Stopping flashes...
10:39 - Setting voltage to 8.500000 V
10:40 - Starting flashes...
10:40 - Stopping flashes...
10:40 - Setting voltage to 8.750000 V
10:40 - Starting flashes...
10:40 - Stopping flashes...
10:40 - Setting voltage to 9.000000 V
10:40 - Starting flashes...
10:40 - Stopping flashes...
10:40 - Setting voltage to 9.250000 V
10:40 - Starting flashes...
10:41 - Stopping flashes...
10:41 - Setting voltage to 9.500000 V
10:41 - Starting flashes...
10:41 - Stopping flashes...
10:41 - Setting voltage to 9.750000 V
10:41 - Starting flashes...
10:41 - Stopping flashes...
10:41 - Setting voltage to 10.000000 V
10:41 - Starting flashes...
10:42 - Stopping flashes...
10:42 - Setting voltage to 10.250000 V
10:42 - Starting flashes...
10:42 - Stopping flashes...
10:42 - Setting voltage to 10.500000 V
10:42 - Starting flashes...
10:42 - Stopping flashes...
10:42 - Setting voltage to 10.750000 V
10:42 - Starting flashes...
10:42 - Stopping flashes...
10:43 - Setting voltage to 11.000000 V
10:43 - Starting flashes...
10:43 - Stopping flashes...
10:43 - Setting voltage to 11.250000 V
10:43 - Starting flashes...
10:43 - Stopping flashes...
10:43 - Setting voltage to 11.500000 V
10:43 - Starting flashes...
10:43 - Stopping flashes...
10:43 - Setting voltage to 11.750000 V
10:43 - Starting flashes...
10:44 - Stopping flashes...
10:44 - Setting voltage to 12.000000 V
10:44 - Starting flashes...
10:44 - Stopping flashes...
10:44 - Setting voltage to 12.250000 V
10:44 - Starting flashes...
10:44 - Stopping flashes...
10:44 - Setting voltage to 12.500000 V
10:44 - Starting flashes...
10:45 - Stopping flashes...
10:45 - Setting voltage to 12.750000 V
10:45 - Starting flashes...
10:45 - Stopping flashes...
10:45 - Setting voltage to 13.000000 V
10:45 - Starting flashes...
10:45 - Stopping flashes...
10:45 - Setting voltage to 13.250000 V
10:45 - Starting flashes...
10:45 - Stopping flashes...
10:46 - Setting voltage to 13.500000 V
10:46 - Starting flashes...
10:46 - Stopping flashes...
10:46 - Setting voltage to 13.750000 V
10:46 - Starting flashes...
10:46 - Stopping flashes...
10:46 - Setting voltage to 14.000000 V
10:46 - Starting flashes...
10:46 - Stopping flashes...
10:46 - Setting voltage to 14.250000 V
10:46 - Starting flashes...
10:47 - Stopping flashes...
10:47 - Setting voltage to 14.500000 V
10:47 - Starting flashes...
10:47 - Stopping flashes...
10:47 - Setting voltage to 14.750000 V
10:47 - Starting flashes...
10:47 - Stopping flashes...
10:47 - Setting voltage to 15.000000 V
10:47 - Starting flashes...
10:48 - Stopping flashes...
10:48 - Setting voltage to 15.250000 V
10:48 - Starting flashes...
10:48 - Stopping flashes...
10:48 - Setting voltage to 15.500000 V
10:48 - Starting flashes...
10:48 - Stopping flashes...
10:48 - Setting voltage to 15.750000 V
10:48 - Starting flashes...
10:49 - Stopping flashes...
10:49 - Setting voltage to 16.000000 V
10:49 - Starting flashes...
10:49 - Stopping flashes...
10:49 - Finished task "Scan voltages"
10:56 - Stopping TIB...
10:56 - Status: TibState.Running
10:56 - Alarms: AlarmVector.ReadError
10:56 - Connection status: True
10:56 - Disabling trigger
10:56 - Disabling PPS
10:56 - Status: TibState.PpsStopped
10:56 - Alarms: AlarmVector.ReadError
10:56 - Connection status: True
10:56 - Closing TIB connection to camera server
10:56 - Status: TibState.PpsStopped
10:56 - Alarms: AlarmVector.ReadError
10:56 - Connection status: False
10:56 - Run duration: 0:17:39
10:56 - Local camera triggers: 0
10:56 - Slow control triggers: 0
10:56 - Single photo-electron triggers: 0
10:56 - Calibration triggers: 37596
10:56 - Software triggers from UCTS: 0
10:56 - Pedestal triggers: 0
10:56 - Collected input triggers: 37596
10:56 - Busy triggers: 0
10:56 - Camera event triggers sent to clusters: 37596
10:56 - Stopping NMC
10:56 - Found 0 PPS errors.