10:10 - ECC is in state EccState.Ready with status EccStatus.NoError
10:10 - ECC temperature sensors: T1= 25.0, T2= 24.4, T3= 25.7, T4= 26.7 deg C
10:10 - 24 V power supply no. 1 is enabled with a current of 8.800 A.
10:10 - Stopping NMC
10:10 - Found 0 PPS errors.
10:10 - Checking high voltages...
10:10 - Starting task "Check HV"
10:10 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181116/config_11modules_HVnom.NMC.xml
10:10 - Done
10:10 - Found 11 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:10 - Found 11 drawer(s). Reference voltage is between 979.98 V and 1182.43 V. Actual voltage is between 980.27 V and 1182.18 V.
10:10 - Maximum difference between expected and actual voltages in drawer 76 is 0.72 V
10:10 - Maximum difference between expected and actual voltages in drawer 77 is 0.41 V
10:10 - Maximum difference between expected and actual voltages in drawer 93 is 0.37 V
10:11 - Maximum difference between expected and actual voltages in drawer 94 is 0.63 V
10:11 - Maximum difference between expected and actual voltages in drawer 110 is 0.59 V
10:11 - Maximum difference between expected and actual voltages in drawer 111 is 0.42 V
10:11 - Maximum difference between expected and actual voltages in drawer 112 is 0.49 V
10:11 - Maximum difference between expected and actual voltages in drawer 128 is 0.48 V
10:11 - Maximum difference between expected and actual voltages in drawer 129 is 0.51 V
10:11 - Maximum difference between expected and actual voltages in drawer 145 is 0.47 V
10:11 - Maximum difference between expected and actual voltages in drawer 146 is 0.58 V
10:11 - Checking status of HVPA module in 11 drawer(s)...
10:11 - Checking status of HVPA channels in 11 drawer(s)...
10:11 - HV is stabilized in all channels.
10:11 - Finished task "Check HV"
10:11 - Starting NMC
10:11 - Clearing PPS error counters
10:11 - Status: TibState.PpsStopped
10:11 - Alarms: AlarmVector.ReadError
10:11 - Connection status: False
10:11 - External delays: Local=0.000 ns, Calibration=76.000 ns, Sphe=0.000 ns
10:11 - Trigger mask: 0x44 = TriggerMask.SlowControl|Calibration
10:11 - Input mask: 0x0
10:11 - Disable BUSY: False
10:11 - Extra BUSY Delay: 0.0
10:11 - Temperature: 35.25
10:11 - Resetting TIB...
10:11 - Failed to call Reset: Bad statuses are present
10:11 - Configuring TIB...
10:11 - Setting TIB forced mode to False
10:11 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:11 - Status: TibState.RunStopped
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Disabling PPS
10:11 - Status: TibState.PpsStopped
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Entering set_external_delay
10:11 - Setting ExternalDelayLocal to 0.000 ns
10:11 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:11 - Entering set_external_delay
10:11 - Setting ExternalDelayCalibration to 76.000 ns
10:11 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:11 - Entering set_external_delay
10:11 - Setting ExternalDelaySphe to 0.000 ns
10:11 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:11 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
10:11 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:11 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:11 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:11 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:11 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:11 - Status: TibState.PpsStopped
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:11 - Writing 10000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:11 - Writing 10000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:11 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:11 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11 - Connecting TIB to camera server at 10.10.4.12:222
10:11 - Starting TIB...
10:11 - Status: TibState.PpsStopped
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Resetting run
10:11 - Wait for UCTS external trigger before enabling trigger...
10:11 - Status: TibState.Standby
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Status: TibState.Standby
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: False
10:11 - Status: TibState.Armed
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: True
10:11 - Starting TIB triggers...
10:11 - Enabling trigger
10:11 - Status: TibState.Running
10:11 - Alarms: AlarmVector.NoAlarm
10:11 - Connection status: True
10:11 - Configuring calibration box...
10:11 - Configuring calibration box with leds=0x358 voltage=12.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
10:11 - Scanning voltages
10:11 - Starting task "Scan voltages"
10:11 - Setting LED mask to 0x0
10:11 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
10:11 - Starting flashes...
10:12 - Stopping flashes...
10:12 - Setting LED mask to 0x358
10:12 - Setting voltage to 8.000000 V
10:12 - Starting flashes...
10:12 - Stopping flashes...
10:12 - Setting voltage to 8.250000 V
10:12 - Starting flashes...
10:12 - Stopping flashes...
10:12 - Setting voltage to 8.500000 V
10:12 - Starting flashes...
10:12 - Stopping flashes...
10:13 - Setting voltage to 8.750000 V
10:13 - Starting flashes...
10:13 - Stopping flashes...
10:13 - Setting voltage to 9.000000 V
10:13 - Starting flashes...
10:13 - Stopping flashes...
10:13 - Setting voltage to 9.250000 V
10:13 - Starting flashes...
10:13 - Stopping flashes...
10:14 - Setting voltage to 9.500000 V
10:14 - Starting flashes...
10:14 - Stopping flashes...
10:14 - Setting voltage to 9.750000 V
10:14 - Starting flashes...
10:14 - Stopping flashes...
10:14 - Setting voltage to 10.000000 V
10:14 - Starting flashes...
10:14 - Stopping flashes...
10:14 - Setting voltage to 10.250000 V
10:14 - Starting flashes...
10:15 - Stopping flashes...
10:15 - Setting voltage to 10.500000 V
10:15 - Starting flashes...
10:15 - Stopping flashes...
10:15 - Setting voltage to 10.750000 V
10:15 - Starting flashes...
10:15 - Stopping flashes...
10:15 - Setting voltage to 11.000000 V
10:15 - Starting flashes...
10:16 - Stopping flashes...
10:16 - Setting voltage to 11.250000 V
10:16 - Starting flashes...
10:16 - Stopping flashes...
10:16 - Setting voltage to 11.500000 V
10:16 - Starting flashes...
10:16 - Stopping flashes...
10:16 - Setting voltage to 11.750000 V
10:16 - Starting flashes...
10:16 - Stopping flashes...
10:17 - Setting voltage to 12.000000 V
10:17 - Starting flashes...
10:17 - Stopping flashes...
10:17 - Setting voltage to 12.250000 V
10:17 - Starting flashes...
10:17 - Stopping flashes...
10:17 - Setting voltage to 12.500000 V
10:17 - Starting flashes...
10:17 - Stopping flashes...
10:17 - Setting voltage to 12.750000 V
10:17 - Starting flashes...
10:18 - Stopping flashes...
10:18 - Setting voltage to 13.000000 V
10:18 - Starting flashes...
10:18 - Stopping flashes...
10:18 - Setting voltage to 13.250000 V
10:18 - Starting flashes...
10:18 - Stopping flashes...
10:18 - Setting voltage to 13.500000 V
10:18 - Starting flashes...
10:19 - Stopping flashes...
10:19 - Setting voltage to 13.750000 V
10:19 - Starting flashes...
10:19 - Stopping flashes...
10:19 - Setting voltage to 14.000000 V
10:19 - Starting flashes...
10:19 - Stopping flashes...
10:19 - Setting voltage to 14.250000 V
10:19 - Starting flashes...
10:19 - Stopping flashes...
10:20 - Setting voltage to 14.500000 V
10:20 - Starting flashes...
10:20 - Stopping flashes...
10:20 - Setting voltage to 14.750000 V
10:20 - Starting flashes...
10:20 - Stopping flashes...
10:20 - Setting voltage to 15.000000 V
10:20 - Starting flashes...
10:20 - Stopping flashes...
10:20 - Setting voltage to 15.250000 V
10:21 - Starting flashes...
10:21 - Stopping flashes...
10:21 - Setting voltage to 15.500000 V
10:21 - Starting flashes...
10:21 - Stopping flashes...
10:21 - Setting voltage to 15.750000 V
10:21 - Starting flashes...
10:21 - Stopping flashes...
10:21 - Setting voltage to 16.000000 V
10:21 - Starting flashes...
10:22 - Stopping flashes...
10:22 - Finished task "Scan voltages"
10:22 - Stopping TIB...
10:22 - Status: TibState.Running
10:22 - Alarms: AlarmVector.ReadError
10:22 - Connection status: True
10:22 - Disabling trigger
10:22 - Disabling PPS
10:22 - Status: TibState.PpsStopped
10:22 - Alarms: AlarmVector.ReadError
10:22 - Connection status: True
10:22 - Closing TIB connection to camera server
10:22 - Status: TibState.PpsStopped
10:22 - Alarms: AlarmVector.ReadError
10:22 - Connection status: False
10:22 - Run duration: 0:10:35
10:22 - Local camera triggers: 0
10:22 - Slow control triggers: 0
10:22 - Single photo-electron triggers: 0
10:22 - Calibration triggers: 37597
10:22 - Software triggers from UCTS: 0
10:22 - Pedestal triggers: 0
10:22 - Collected input triggers: 37597
10:22 - Busy triggers: 0
10:22 - Camera event triggers sent to clusters: 37597
10:22 - Stopping NMC
10:22 - Found 0 PPS errors.