09:52 - ECC is in state EccState.Ready with status EccStatus.NoError
09:52 - ECC temperature sensors: T1= 25.1, T2= 24.6, T3= 25.8, T4= 26.8 deg C
09:52 - 24 V power supply no. 1 is enabled with a current of 8.740 A.
09:52 - Stopping NMC
09:52 - Found 0 PPS errors.
09:52 - Checking high voltages...
09:52 - Starting task "Check HV"
09:52 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181116/config_11modules_HVnom.NMC.xml
09:52 - Done
09:52 - Found 11 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
09:52 - Found 11 drawer(s). Reference voltage is between 979.98 V and 1182.43 V. Actual voltage is between 979.66 V and 1182.79 V.
09:52 - Maximum difference between expected and actual voltages in drawer 76 is 0.21 V
09:52 - Maximum difference between expected and actual voltages in drawer 77 is 0.36 V
09:52 - Maximum difference between expected and actual voltages in drawer 93 is 0.37 V
09:52 - Maximum difference between expected and actual voltages in drawer 94 is 0.41 V
09:52 - Maximum difference between expected and actual voltages in drawer 110 is 0.50 V
09:52 - Maximum difference between expected and actual voltages in drawer 111 is 0.66 V
09:52 - Maximum difference between expected and actual voltages in drawer 112 is 0.49 V
09:52 - Maximum difference between expected and actual voltages in drawer 128 is 0.44 V
09:52 - Maximum difference between expected and actual voltages in drawer 129 is 0.46 V
09:52 - Maximum difference between expected and actual voltages in drawer 145 is 0.47 V
09:52 - Maximum difference between expected and actual voltages in drawer 146 is 0.58 V
09:52 - Checking status of HVPA module in 11 drawer(s)...
09:52 - Checking status of HVPA channels in 11 drawer(s)...
09:52 - HV is stabilized in all channels.
09:52 - Finished task "Check HV"
09:52 - Starting NMC
09:52 - Clearing PPS error counters
09:52 - Configuring TIB...
09:52 - Setting TIB forced mode to False
09:52 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
09:52 - Status: TibState.RunStopped
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: False
09:52 - Disabling PPS
09:52 - Status: TibState.PpsStopped
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: False
09:52 - Entering set_external_delay
09:52 - Setting ExternalDelayLocal to 0.000 ns
09:52 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
09:52 - Entering set_external_delay
09:52 - Setting ExternalDelayCalibration to 76.000 ns
09:52 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
09:52 - Entering set_external_delay
09:52 - Setting ExternalDelaySphe to 0.000 ns
09:52 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
09:52 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
09:52 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
09:52 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
09:52 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
09:52 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
09:52 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
09:52 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
09:52 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
09:52 - Status: TibState.PpsStopped
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: False
09:52 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
09:52 - Writing 10000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
09:52 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:52 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
09:52 - Writing 10000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
09:52 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
09:52 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:52 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
09:52 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
09:52 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:52 - Connecting TIB to camera server at 10.10.4.12:222
09:52 - Starting TIB...
09:52 - Status: TibState.PpsStopped
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: False
09:52 - Resetting run
09:52 - Wait for UCTS external trigger before enabling trigger...
09:52 - Status: TibState.Standby
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: False
09:52 - Status: TibState.Standby
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: False
09:52 - Status: TibState.Armed
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: True
09:52 - Starting TIB triggers...
09:52 - Enabling trigger
09:52 - Status: TibState.Running
09:52 - Alarms: AlarmVector.NoAlarm
09:52 - Connection status: True
09:53 - Configuring calibration box...
09:53 - Configuring calibration box with leds=0x40 voltage=12.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
09:53 - Scanning voltages
09:53 - Starting task "Scan voltages"
09:53 - Setting LED mask to 0x0
09:53 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
09:53 - Starting flashes...
09:53 - Stopping flashes...
09:53 - Setting LED mask to 0x40
09:54 - Setting voltage to 8.000000 V
09:54 - Starting flashes...
09:54 - Stopping flashes...
09:54 - Setting voltage to 8.250000 V
09:54 - Starting flashes...
09:54 - Stopping flashes...
09:54 - Setting voltage to 8.500000 V
09:54 - Starting flashes...
09:54 - Stopping flashes...
09:54 - Setting voltage to 8.750000 V
09:55 - Starting flashes...
09:55 - Stopping flashes...
09:55 - Setting voltage to 9.000000 V
09:55 - Starting flashes...
09:55 - Stopping flashes...
09:55 - Setting voltage to 9.250000 V
09:55 - Starting flashes...
09:55 - Stopping flashes...
09:55 - Setting voltage to 9.500000 V
09:55 - Starting flashes...
09:56 - Stopping flashes...
09:56 - Setting voltage to 9.750000 V
09:56 - Starting flashes...
09:56 - Stopping flashes...
09:56 - Setting voltage to 10.000000 V
09:56 - Starting flashes...
09:56 - Stopping flashes...
09:56 - Setting voltage to 10.250000 V
09:56 - Starting flashes...
09:57 - Stopping flashes...
09:57 - Setting voltage to 10.500000 V
09:57 - Starting flashes...
09:57 - Stopping flashes...
09:57 - Setting voltage to 10.750000 V
09:57 - Starting flashes...
09:57 - Stopping flashes...
09:57 - Setting voltage to 11.000000 V
09:57 - Starting flashes...
09:57 - Stopping flashes...
09:58 - Setting voltage to 11.250000 V
09:58 - Starting flashes...
09:58 - Stopping flashes...
09:58 - Setting voltage to 11.500000 V
09:58 - Starting flashes...
09:58 - Stopping flashes...
09:58 - Setting voltage to 11.750000 V
09:58 - Starting flashes...
09:58 - Stopping flashes...
09:58 - Setting voltage to 12.000000 V
09:58 - Starting flashes...
09:59 - Stopping flashes...
09:59 - Setting voltage to 12.250000 V
09:59 - Starting flashes...
09:59 - Stopping flashes...
09:59 - Setting voltage to 12.500000 V
09:59 - Starting flashes...
09:59 - Stopping flashes...
09:59 - Setting voltage to 12.750000 V
09:59 - Starting flashes...
10:00 - Stopping flashes...
10:00 - Setting voltage to 13.000000 V
10:00 - Starting flashes...
10:00 - Stopping flashes...
10:00 - Setting voltage to 13.250000 V
10:00 - Starting flashes...
10:00 - Stopping flashes...
10:00 - Setting voltage to 13.500000 V
10:00 - Starting flashes...
10:00 - Stopping flashes...
10:01 - Setting voltage to 13.750000 V
10:01 - Starting flashes...
10:01 - Stopping flashes...
10:01 - Setting voltage to 14.000000 V
10:01 - Starting flashes...
10:01 - Stopping flashes...
10:01 - Setting voltage to 14.250000 V
10:01 - Starting flashes...
10:01 - Stopping flashes...
10:01 - Setting voltage to 14.500000 V
10:01 - Starting flashes...
10:02 - Stopping flashes...
10:02 - Setting voltage to 14.750000 V
10:02 - Starting flashes...
10:02 - Stopping flashes...
10:02 - Setting voltage to 15.000000 V
10:02 - Starting flashes...
10:02 - Stopping flashes...
10:02 - Setting voltage to 15.250000 V
10:02 - Starting flashes...
10:03 - Stopping flashes...
10:03 - Setting voltage to 15.500000 V
10:03 - Starting flashes...
10:03 - Stopping flashes...
10:03 - Setting voltage to 15.750000 V
10:03 - Starting flashes...
10:03 - Stopping flashes...
10:03 - Setting voltage to 16.000000 V
10:03 - Starting flashes...
10:04 - Stopping flashes...
10:04 - Finished task "Scan voltages"
10:09 - Stopping TIB...
10:09 - Status: TibState.Running
10:09 - Alarms: AlarmVector.ReadError
10:09 - Connection status: True
10:09 - Disabling trigger
10:09 - Disabling PPS
10:09 - Status: TibState.PpsStopped
10:09 - Alarms: AlarmVector.ReadError
10:09 - Connection status: True
10:09 - Closing TIB connection to camera server
10:09 - Status: TibState.PpsStopped
10:09 - Alarms: AlarmVector.ReadError
10:09 - Connection status: False
10:09 - Run duration: 0:16:43
10:09 - Local camera triggers: 0
10:09 - Slow control triggers: 0
10:09 - Single photo-electron triggers: 0
10:09 - Calibration triggers: 37598
10:09 - Software triggers from UCTS: 0
10:09 - Pedestal triggers: 0
10:09 - Collected input triggers: 37598
10:09 - Busy triggers: 0
10:09 - Camera event triggers sent to clusters: 37598