15:09 - ECC is in state EccState.Ready with status EccStatus.NoError
15:09 - ECC temperature sensors: T1= 23.6, T2= 23.1, T3= 24.4, T4= 25.5 deg C
15:09 - 24 V power supply no. 1 is enabled with a current of 0.210 A.
15:09 - Starting task "Configure NMC"
15:09 - Configuring modules with configuration /local/home/cta_test_bench/config/2018/20181031/config_1module.NMC.xml
15:09 - Stripping HV voltages from configuration
15:09 - Setting HV current limits to maximum
15:09 - Successfully configured 1 module(s)
15:09 - NMC is in state NmcState.Configured and knows of 1 drawer(s)
15:09 - Found 0 PPS errors.
15:09 - Finished task "Configure NMC"
15:10 - Starting NMC
15:10 - Clearing PPS error counters
15:10 - Setting HVPA current limit to 12489.75 uA
15:10 - Setting HVPA ramp speed to 500 V/s
15:10 - Switching HVPA to state Wait
15:10 - Switching drawer 128 HVPA to state Wait
15:10 - Checking high voltages...
15:10 - Starting task "Check HV"
15:10 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module.NMC.xml
15:10 - Done
15:10 - Found 0 drawer(s) in Nominal state, 0 in Low state and 1 in Wait state
15:10 - Found 1 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 13.42 V and 19.52 V.
15:10 - Maximum difference between expected and actual voltages in drawer 128 is 19.52 V
15:10 - Checking status of HVPA module in 1 drawer(s)...
15:10 - Checking status of HVPA channels in 1 drawer(s)...
15:10 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:10 - Finished task "Check HV"
15:10 - Checking high voltages...
15:10 - Starting task "Check HV"
15:10 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module.NMC.xml
15:10 - Done
15:10 - Found 0 drawer(s) in Nominal state, 0 in Low state and 1 in Wait state
15:10 - Found 1 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 12.81 V and 19.52 V.
15:10 - Maximum difference between expected and actual voltages in drawer 128 is 19.52 V
15:10 - Checking status of HVPA module in 1 drawer(s)...
15:10 - Checking status of HVPA channels in 1 drawer(s)...
15:10 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:10 - Finished task "Check HV"
15:11 - Configuring TIB...
15:11 - Setting TIB forced mode to False
15:11 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:11 - Status: TibState.PpsStopped
15:11 - Alarms: AlarmVector.ReadError
15:11 - Connection status: False
15:11 - Entering set_external_delay
15:11 - Setting ExternalDelayLocal to 0.000 ns
15:11 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:11 - Entering set_external_delay
15:11 - Setting ExternalDelayCalibration to 76.000 ns
15:11 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:11 - Entering set_external_delay
15:11 - Setting ExternalDelaySphe to 0.000 ns
15:11 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:11 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
15:11 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:11 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:11 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:11 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:11 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:11 - Status: TibState.PpsStopped
15:11 - Alarms: AlarmVector.ReadError
15:11 - Connection status: False
15:11 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:11 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:11 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:11 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:11 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:11 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:11 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:11 - Connecting TIB to camera server at 10.10.4.12:222
15:11 - Starting TIB...
15:11 - Status: TibState.PpsStopped
15:11 - Alarms: AlarmVector.ReadError
15:11 - Connection status: False
15:11 - Resetting run
15:11 - Wait for UCTS external trigger before enabling trigger...
15:11 - Status: TibState.Standby
15:11 - Alarms: AlarmVector.NoAlarm
15:11 - Connection status: False
15:11 - Status: TibState.Standby
15:11 - Alarms: AlarmVector.NoAlarm
15:11 - Connection status: False
15:11 - Status: TibState.Armed
15:11 - Alarms: AlarmVector.NoAlarm
15:11 - Connection status: True
15:11 - Starting TIB triggers...
15:11 - Enabling trigger
15:11 - Status: TibState.Running
15:11 - Alarms: AlarmVector.NoAlarm
15:11 - Connection status: True
15:11 - Configuring calibration box...
15:11 - Configuring calibration box with leds=0x0 voltage=9.00 frequency=5000.0/1 central_current=0.0 duration=400 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
15:11 - Starting flashes...
15:12 - Stopping TIB...
15:12 - Status: TibState.Running
15:12 - Alarms: AlarmVector.ReadError
15:12 - Connection status: True
15:12 - Disabling trigger
15:12 - Disabling PPS
15:12 - Status: TibState.PpsStopped
15:12 - Alarms: AlarmVector.ReadError
15:12 - Connection status: True
15:12 - Closing TIB connection to camera server
15:12 - Status: TibState.PpsStopped
15:12 - Alarms: AlarmVector.ReadError
15:12 - Connection status: False
15:12 - Run duration: 0:00:58
15:12 - Local camera triggers: 0
15:12 - Slow control triggers: 0
15:12 - Single photo-electron triggers: 0
15:12 - Calibration triggers: 199902
15:12 - Software triggers from UCTS: 0
15:12 - Pedestal triggers: 0
15:12 - Collected input triggers: 199902
15:12 - Busy triggers: 0
15:12 - Camera event triggers sent to clusters: 199902