14:46 - ECC is in state EccState.Ready with status EccStatus.NoError
14:46 - ECC temperature sensors: T1= 23.7, T2= 23.2, T3= 24.4, T4= 25.6 deg C
14:46 - 24 V power supply no. 1 is enabled with a current of 0.190 A.
14:47 - Starting task "Configure NMC"
14:47 - Configuring modules with configuration /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Setting HV current limits to maximum
14:47 - Successfully configured 0 module(s)
14:47 - NMC is in state NmcState.Configured and knows of 1 drawer(s)
14:47 - Found 0 PPS errors.
14:47 - Finished task "Configure NMC"
14:47 - Setting HVPA current limit to 12489.75 uA
14:47 - Setting HVPA ramp speed to 20 V/s
14:47 - Switching HVPA to state Nominal
14:47 - Switching drawer 128 HVPA to state Nominal
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 935.74 V and 974.78 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 33.33 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
14:47 - Finished task "Check HV"
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.77 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 0.54 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV is stabilized in all channels.
14:47 - Finished task "Check HV"
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.77 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 0.58 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV is stabilized in all channels.
14:47 - Finished task "Check HV"
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.85 V and 1010.16 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 0.40 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV is stabilized in all channels.
14:47 - Finished task "Check HV"
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.85 V and 1010.77 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 0.38 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV is stabilized in all channels.
14:47 - Finished task "Check HV"
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.77 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 0.38 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV is stabilized in all channels.
14:47 - Finished task "Check HV"
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.16 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 0.54 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV is stabilized in all channels.
14:47 - Finished task "Check HV"
14:47 - Checking high voltages...
14:47 - Starting task "Check HV"
14:47 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181031/config_1module_DACL_HV.NMC.xml
14:47 - Done
14:47 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:47 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.85 V and 1010.77 V.
14:47 - Maximum difference between expected and actual voltages in drawer 128 is 0.38 V
14:47 - Checking status of HVPA module in 1 drawer(s)...
14:47 - Checking status of HVPA channels in 1 drawer(s)...
14:47 - HV is stabilized in all channels.
14:47 - Finished task "Check HV"
14:47 - Starting NMC
14:47 - Clearing PPS error counters
14:48 - Configuring TIB...
14:48 - Setting TIB forced mode to False
14:48 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:48 - Status: TibState.PpsStopped
14:48 - Alarms: AlarmVector.ReadError
14:48 - Connection status: False
14:48 - Entering set_external_delay
14:48 - Setting ExternalDelayLocal to 0.000 ns
14:48 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
14:48 - Entering set_external_delay
14:48 - Setting ExternalDelayCalibration to 76.000 ns
14:48 - Writing 76.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:48 - Entering set_external_delay
14:48 - Setting ExternalDelaySphe to 0.000 ns
14:48 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:48 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
14:48 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:48 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:48 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:48 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:48 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:48 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:48 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:48 - Status: TibState.PpsStopped
14:48 - Alarms: AlarmVector.ReadError
14:48 - Connection status: False
14:48 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:48 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:48 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:48 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:48 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:48 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:48 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:48 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:48 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:48 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:48 - Connecting TIB to camera server at 10.10.4.12:222
14:48 - Starting TIB...
14:48 - Status: TibState.PpsStopped
14:48 - Alarms: AlarmVector.ReadError
14:48 - Connection status: False
14:48 - Resetting run
14:48 - Wait for UCTS external trigger before enabling trigger...
14:48 - Status: TibState.Standby
14:48 - Alarms: AlarmVector.NoAlarm
14:48 - Connection status: False
14:48 - Status: TibState.Standby
14:48 - Alarms: AlarmVector.NoAlarm
14:48 - Connection status: False
14:48 - Status: TibState.Armed
14:48 - Alarms: AlarmVector.NoAlarm
14:48 - Connection status: True
14:48 - Starting TIB triggers...
14:48 - Enabling trigger
14:48 - Status: TibState.Running
14:48 - Alarms: AlarmVector.NoAlarm
14:48 - Connection status: True
14:48 - Configuring calibration box...
14:48 - Configuring calibration box with leds=0x0 voltage=9.00 frequency=5000.0/1 central_current=0.0 duration=400 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
14:48 - Starting flashes...
14:49 - Stopping TIB...
14:49 - Status: TibState.Running
14:49 - Alarms: AlarmVector.ReadError
14:49 - Connection status: True
14:49 - Disabling trigger
14:49 - Disabling PPS
14:49 - Status: TibState.PpsStopped
14:49 - Alarms: AlarmVector.ReadError
14:49 - Connection status: True
14:49 - Closing TIB connection to camera server
14:49 - Status: TibState.PpsStopped
14:49 - Alarms: AlarmVector.ReadError
14:49 - Connection status: False
14:49 - Run duration: 0:01:18
14:49 - Local camera triggers: 0
14:49 - Slow control triggers: 0
14:49 - Single photo-electron triggers: 0
14:49 - Calibration triggers: 199551
14:49 - Software triggers from UCTS: 0
14:49 - Pedestal triggers: 0
14:49 - Collected input triggers: 199551
14:49 - Busy triggers: 0
14:49 - Camera event triggers sent to clusters: 199551
14:49 - Stopping NMC
14:49 - Found 0 PPS errors.