15:08 - ECC is in state EccState.Ready with status EccStatus.NoError
15:08 - ECC temperature sensors: T1= 28.4, T2= 27.8, T3= 29.1, T4= 30.0 deg C
15:08 - 24 V power supply no. 1 is enabled with a current of -0.100 A.
15:08 - Starting task "Configure NMC"
15:08 - Configuring modules with configuration /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:08 - NMC is in state NmcState.Configured and knows of 1 drawer(s)
15:08 - Found 0 PPS errors.
15:08 - Finished task "Configure NMC"
15:08 - Setting HVPA ramp sped to 20 V/s
15:08 - Switching HVPA to state Nominal
15:08 - Switching drawer 128 HVPA to state Nominal
15:08 - Checking high voltages...
15:08 - Starting task "Check HV"
15:08 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:08 - Done
15:08 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:08 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 200.08 V and 206.79 V.
15:08 - Maximum difference between expected and actual voltages in drawer 128 is 800.64 V
15:08 - Checking status of HVPA module in 1 drawer(s)...
15:08 - Checking status of HVPA channels in 1 drawer(s)...
15:08 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:08 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 239.73 V and 247.05 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 761.60 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 279.38 V and 286.09 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 721.95 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 310.49 V and 317.20 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 691.45 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 342.21 V and 349.53 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 659.12 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 376.98 V and 383.69 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 624.96 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 412.36 V and 419.68 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 589.58 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 462.99 V and 469.70 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 540.17 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 502.64 V and 510.57 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 499.30 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 539.24 V and 547.17 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 462.70 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 569.74 V and 577.67 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 432.81 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 602.07 V and 610.00 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 399.87 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 636.84 V and 645.38 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 365.71 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 669.17 V and 677.10 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 333.99 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 706.99 V and 715.53 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 295.56 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 751.52 V and 760.67 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 251.03 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.16 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 1.00 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV is stabilized in all channels.
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.16 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 0.39 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV is stabilized in all channels.
15:09 - Finished task "Check HV"
15:09 - Checking high voltages...
15:09 - Starting task "Check HV"
15:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
15:09 - Done
15:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.16 V.
15:09 - Maximum difference between expected and actual voltages in drawer 128 is 0.37 V
15:09 - Checking status of HVPA module in 1 drawer(s)...
15:09 - Checking status of HVPA channels in 1 drawer(s)...
15:09 - HV is stabilized in all channels.
15:09 - Finished task "Check HV"
15:10 - Starting NMC
15:10 - Clearing PPS error counters
15:10 - Stopping flashes...
15:10 - Configuring TIB...
15:10 - Setting TIB forced mode to False
15:10 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:10 - Status: TibState.RunStopped
15:10 - Alarms: AlarmVector.NoAlarm
15:10 - Connection status: False
15:10 - Disabling PPS
15:10 - Status: TibState.PpsStopped
15:10 - Alarms: AlarmVector.NoAlarm
15:10 - Connection status: False
15:10 - Entering set_external_delay
15:10 - Setting ExternalDelayLocal to 0.000 ns
15:10 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:10 - Entering set_external_delay
15:10 - Setting ExternalDelayCalibration to 0.000 ns
15:10 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:10 - Entering set_external_delay
15:10 - Setting ExternalDelaySphe to 0.000 ns
15:10 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:10 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
15:10 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:10 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:10 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:10 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:10 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:10 - Status: TibState.PpsStopped
15:10 - Alarms: AlarmVector.NoAlarm
15:10 - Connection status: False
15:10 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:10 - Writing 10000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:10 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:10 - Writing 10000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:10 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:10 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:10 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:10 - Connecting TIB to camera server at 10.10.4.12:222
15:10 - Starting TIB...
15:10 - Status: TibState.PpsStopped
15:10 - Alarms: AlarmVector.NoAlarm
15:10 - Connection status: False
15:10 - Resetting run
15:10 - Wait for UCTS external trigger before enabling trigger...
15:10 - Status: TibState.Standby
15:10 - Alarms: AlarmVector.NoAlarm
15:10 - Connection status: False
15:10 - Status: TibState.Standby
15:10 - Alarms: AlarmVector.NoAlarm
15:10 - Connection status: False
15:10 - Status: TibState.Armed
15:10 - Alarms: AlarmVector.NoAlarm
15:10 - Connection status: True
15:11 - Starting TIB triggers...
15:11 - Enabling trigger
15:11 - Status: TibState.Running
15:11 - Alarms: AlarmVector.NoAlarm
15:11 - Connection status: True
2018-10-15 15:11:26,558 Scanning positions of XY table
2018-10-15 15:11:26,572 Exiting scan mode
2018-10-15 15:11:26,574 Moving to next XY table position
2018-10-15 15:11:28,588 Moving to parking position
2018-10-15 15:11:41,768 XY table IS parked
2018-10-15 15:11:51,782 Selecting XY table pixel: 3
2018-10-15 15:11:51,784 Configuring calibration box with leds=0x800 voltage=8.00 frequency=500.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
2018-10-15 15:11:51,877 Moving to central position 166
2018-10-15 15:11:51,877 Selecting XY table position: 166
2018-10-15 15:11:51,879 Moving to next XY table position
2018-10-15 15:11:52,923 XY table IS busy
2018-10-15 15:12:23,344 XY table is NOT busy
2018-10-15 15:12:34,947 Starting flashes...
2018-10-15 15:12:38,000 Stopping flashes...
2018-10-15 15:12:40,154 Moving to position 332
2018-10-15 15:12:40,154 Selecting XY table position: 332
2018-10-15 15:12:40,155 Moving to next XY table position
2018-10-15 15:12:40,583 XY table IS busy
2018-10-15 15:12:58,836 XY table is NOT busy
2018-10-15 15:13:08,842 Starting flashes...
2018-10-15 15:13:11,895 Stopping flashes...
2018-10-15 15:13:12,946 Moving to position 322
2018-10-15 15:13:12,946 Selecting XY table position: 322
2018-10-15 15:13:12,948 Moving to next XY table position
2018-10-15 15:13:14,048 XY table IS busy
2018-10-15 15:13:22,159 XY table is NOT busy
2018-10-15 15:13:32,168 Starting flashes...
2018-10-15 15:13:35,220 Stopping flashes...
2018-10-15 15:13:36,271 Moving to position 312
2018-10-15 15:13:36,271 Selecting XY table position: 312
2018-10-15 15:13:36,273 Moving to next XY table position
2018-10-15 15:13:37,370 XY table IS busy
2018-10-15 15:13:45,483 XY table is NOT busy
2018-10-15 15:13:55,488 Starting flashes...
2018-10-15 15:13:58,540 Stopping flashes...
2018-10-15 15:13:59,591 Moving to position 302
2018-10-15 15:13:59,591 Selecting XY table position: 302
2018-10-15 15:13:59,592 Moving to next XY table position
2018-10-15 15:14:00,693 XY table IS busy
2018-10-15 15:14:08,806 XY table is NOT busy
2018-10-15 15:14:18,814 Starting flashes...
2018-10-15 15:14:21,866 Stopping flashes...
2018-10-15 15:14:22,917 Moving to position 292
2018-10-15 15:14:22,917 Selecting XY table position: 292
2018-10-15 15:14:22,919 Moving to next XY table position
2018-10-15 15:14:24,017 XY table IS busy
2018-10-15 15:14:32,130 XY table is NOT busy
2018-10-15 15:14:42,138 Starting flashes...
2018-10-15 15:14:45,189 Stopping flashes...
2018-10-15 15:14:46,240 Moving to position 282
2018-10-15 15:14:46,240 Selecting XY table position: 282
2018-10-15 15:14:46,241 Moving to next XY table position
2018-10-15 15:14:47,339 XY table IS busy
2018-10-15 15:14:55,452 XY table is NOT busy
2018-10-15 15:15:05,461 Starting flashes...
2018-10-15 15:15:08,514 Stopping flashes...
2018-10-15 15:15:09,565 Moving to position 272
2018-10-15 15:15:09,565 Selecting XY table position: 272
2018-10-15 15:15:09,567 Moving to next XY table position
2018-10-15 15:15:10,664 XY table IS busy
2018-10-15 15:15:18,776 XY table is NOT busy
2018-10-15 15:15:28,786 Starting flashes...
2018-10-15 15:15:31,837 Stopping flashes...
2018-10-15 15:15:32,889 Moving to position 262
2018-10-15 15:15:32,889 Selecting XY table position: 262
2018-10-15 15:15:32,890 Moving to next XY table position
2018-10-15 15:15:33,986 XY table IS busy
2018-10-15 15:15:42,099 XY table is NOT busy
2018-10-15 15:15:52,107 Starting flashes...
2018-10-15 15:15:55,157 Stopping flashes...
2018-10-15 15:15:56,208 Moving to position 252
2018-10-15 15:15:56,208 Selecting XY table position: 252
2018-10-15 15:15:56,210 Moving to next XY table position
2018-10-15 15:15:57,310 XY table IS busy
2018-10-15 15:16:05,421 XY table is NOT busy
2018-10-15 15:16:15,430 Starting flashes...
2018-10-15 15:16:18,483 Stopping flashes...
2018-10-15 15:16:19,534 Moving to position 242
2018-10-15 15:16:19,534 Selecting XY table position: 242
2018-10-15 15:16:19,536 Moving to next XY table position
2018-10-15 15:16:20,633 XY table IS busy
2018-10-15 15:16:28,746 XY table is NOT busy
2018-10-15 15:16:38,755 Starting flashes...
2018-10-15 15:16:41,806 Stopping flashes...
2018-10-15 15:16:42,857 Moving to position 232
2018-10-15 15:16:42,857 Selecting XY table position: 232
2018-10-15 15:16:42,859 Moving to next XY table position
2018-10-15 15:16:43,957 XY table IS busy
2018-10-15 15:16:52,068 XY table is NOT busy
2018-10-15 15:17:02,077 Starting flashes...
2018-10-15 15:17:05,129 Stopping flashes...
2018-10-15 15:17:06,179 Moving to position 222
2018-10-15 15:17:06,179 Selecting XY table position: 222
2018-10-15 15:17:06,181 Moving to next XY table position
2018-10-15 15:17:07,279 XY table IS busy
2018-10-15 15:17:15,393 XY table is NOT busy
2018-10-15 15:17:25,402 Starting flashes...
2018-10-15 15:17:28,453 Stopping flashes...
2018-10-15 15:17:29,504 Moving to position 212
2018-10-15 15:17:29,504 Selecting XY table position: 212
2018-10-15 15:17:29,505 Moving to next XY table position
2018-10-15 15:17:30,603 XY table IS busy
2018-10-15 15:17:38,715 XY table is NOT busy
2018-10-15 15:17:48,725 Starting flashes...
2018-10-15 15:17:51,777 Stopping flashes...
2018-10-15 15:17:52,828 Moving to position 202
2018-10-15 15:17:52,828 Selecting XY table position: 202
2018-10-15 15:17:52,830 Moving to next XY table position
2018-10-15 15:17:53,926 XY table IS busy
2018-10-15 15:18:02,038 XY table is NOT busy
2018-10-15 15:18:12,041 Starting flashes...
2018-10-15 15:18:15,093 Stopping flashes...
2018-10-15 15:18:16,143 Moving to position 192
2018-10-15 15:18:16,143 Selecting XY table position: 192
2018-10-15 15:18:16,145 Moving to next XY table position
2018-10-15 15:18:17,249 XY table IS busy
2018-10-15 15:18:25,361 XY table is NOT busy
2018-10-15 15:18:35,363 Starting flashes...
2018-10-15 15:18:38,414 Stopping flashes...
2018-10-15 15:18:39,465 Moving to position 182
2018-10-15 15:18:39,465 Selecting XY table position: 182
2018-10-15 15:18:39,467 Moving to next XY table position
2018-10-15 15:18:40,572 XY table IS busy
2018-10-15 15:18:48,684 XY table is NOT busy
2018-10-15 15:18:58,694 Starting flashes...
2018-10-15 15:19:01,746 Stopping flashes...
2018-10-15 15:19:02,797 Moving to position 172
2018-10-15 15:19:02,797 Selecting XY table position: 172
2018-10-15 15:19:02,799 Moving to next XY table position
2018-10-15 15:19:03,896 XY table IS busy
2018-10-15 15:19:12,009 XY table is NOT busy
2018-10-15 15:19:22,014 Starting flashes...
2018-10-15 15:19:25,066 Stopping flashes...
2018-10-15 15:19:26,117 Moving to position 162
2018-10-15 15:19:26,117 Selecting XY table position: 162
2018-10-15 15:19:26,118 Moving to next XY table position
2018-10-15 15:19:27,219 XY table IS busy
2018-10-15 15:19:35,331 XY table is NOT busy
2018-10-15 15:19:45,339 Starting flashes...
2018-10-15 15:19:48,391 Stopping flashes...
2018-10-15 15:19:49,441 Moving to position 152
2018-10-15 15:19:49,441 Selecting XY table position: 152
2018-10-15 15:19:49,443 Moving to next XY table position
2018-10-15 15:19:50,542 XY table IS busy
2018-10-15 15:19:58,656 XY table is NOT busy
2018-10-15 15:20:08,664 Starting flashes...
2018-10-15 15:20:11,716 Stopping flashes...
2018-10-15 15:20:12,766 Moving to position 142
2018-10-15 15:20:12,766 Selecting XY table position: 142
2018-10-15 15:20:12,768 Moving to next XY table position
2018-10-15 15:20:13,865 XY table IS busy
2018-10-15 15:20:21,978 XY table is NOT busy
2018-10-15 15:20:31,987 Starting flashes...
2018-10-15 15:20:35,039 Stopping flashes...
2018-10-15 15:20:36,089 Moving to position 132
2018-10-15 15:20:36,089 Selecting XY table position: 132
2018-10-15 15:20:36,091 Moving to next XY table position
2018-10-15 15:20:37,189 XY table IS busy
2018-10-15 15:20:45,301 XY table is NOT busy
2018-10-15 15:20:55,309 Starting flashes...
2018-10-15 15:20:58,361 Stopping flashes...
2018-10-15 15:20:59,411 Moving to position 122
2018-10-15 15:20:59,412 Selecting XY table position: 122
2018-10-15 15:20:59,413 Moving to next XY table position
2018-10-15 15:21:00,512 XY table IS busy
2018-10-15 15:21:08,624 XY table is NOT busy
2018-10-15 15:21:18,632 Starting flashes...
2018-10-15 15:21:21,684 Stopping flashes...
2018-10-15 15:21:22,735 Moving to position 112
2018-10-15 15:21:22,735 Selecting XY table position: 112
2018-10-15 15:21:22,737 Moving to next XY table position
2018-10-15 15:21:23,835 XY table IS busy
2018-10-15 15:21:31,947 XY table is NOT busy
2018-10-15 15:21:41,955 Starting flashes...
2018-10-15 15:21:45,006 Stopping flashes...
2018-10-15 15:21:46,057 Moving to position 102
2018-10-15 15:21:46,058 Selecting XY table position: 102
2018-10-15 15:21:46,060 Moving to next XY table position
2018-10-15 15:21:47,158 XY table IS busy
2018-10-15 15:21:55,272 XY table is NOT busy
2018-10-15 15:22:05,276 Starting flashes...
2018-10-15 15:22:08,328 Stopping flashes...
2018-10-15 15:22:09,379 Moving to position 92
2018-10-15 15:22:09,379 Selecting XY table position: 92
2018-10-15 15:22:09,381 Moving to next XY table position
2018-10-15 15:22:10,483 XY table IS busy
2018-10-15 15:22:18,594 XY table is NOT busy
2018-10-15 15:22:28,600 Starting flashes...
2018-10-15 15:22:31,652 Stopping flashes...
2018-10-15 15:22:32,703 Moving to position 82
2018-10-15 15:22:32,703 Selecting XY table position: 82
2018-10-15 15:22:32,705 Moving to next XY table position
2018-10-15 15:22:33,805 XY table IS busy
2018-10-15 15:22:41,918 XY table is NOT busy
2018-10-15 15:22:51,928 Starting flashes...
2018-10-15 15:22:54,970 Stopping flashes...
2018-10-15 15:22:56,020 Moving to position 72
2018-10-15 15:22:56,020 Selecting XY table position: 72
2018-10-15 15:22:56,021 Moving to next XY table position
2018-10-15 15:22:57,128 XY table IS busy
2018-10-15 15:23:05,240 XY table is NOT busy
2018-10-15 15:23:15,241 Starting flashes...
2018-10-15 15:23:18,292 Stopping flashes...
2018-10-15 15:23:19,343 Moving to position 62
2018-10-15 15:23:19,343 Selecting XY table position: 62
2018-10-15 15:23:19,345 Moving to next XY table position
2018-10-15 15:23:20,451 XY table IS busy
2018-10-15 15:23:28,564 XY table is NOT busy
2018-10-15 15:23:38,573 Starting flashes...
2018-10-15 15:23:41,624 Stopping flashes...
2018-10-15 15:23:42,675 Moving to position 52
2018-10-15 15:23:42,675 Selecting XY table position: 52
2018-10-15 15:23:42,676 Moving to next XY table position
2018-10-15 15:23:43,774 XY table IS busy
2018-10-15 15:23:51,887 XY table is NOT busy
2018-10-15 15:24:01,897 Starting flashes...
2018-10-15 15:24:04,948 Stopping flashes...
2018-10-15 15:24:05,999 Moving to position 42
2018-10-15 15:24:05,999 Selecting XY table position: 42
2018-10-15 15:24:06,001 Moving to next XY table position
2018-10-15 15:24:07,098 XY table IS busy
2018-10-15 15:24:15,212 XY table is NOT busy
2018-10-15 15:24:25,222 Starting flashes...
2018-10-15 15:24:28,273 Stopping flashes...
2018-10-15 15:24:29,324 Moving to position 32
2018-10-15 15:24:29,324 Selecting XY table position: 32
2018-10-15 15:24:29,325 Moving to next XY table position
2018-10-15 15:24:30,426 XY table IS busy
2018-10-15 15:24:38,534 XY table is NOT busy
2018-10-15 15:24:48,544 Starting flashes...
2018-10-15 15:24:51,598 Stopping flashes...
2018-10-15 15:24:52,649 Moving to position 22
2018-10-15 15:24:52,649 Selecting XY table position: 22
2018-10-15 15:24:52,651 Moving to next XY table position
2018-10-15 15:24:53,745 XY table IS busy
2018-10-15 15:25:01,858 XY table is NOT busy
2018-10-15 15:25:11,865 Starting flashes...
2018-10-15 15:25:14,916 Stopping flashes...
2018-10-15 15:25:15,967 Moving to position 12
2018-10-15 15:25:15,968 Selecting XY table position: 12
2018-10-15 15:25:15,969 Moving to next XY table position
2018-10-15 15:25:17,068 XY table IS busy
2018-10-15 15:25:25,180 XY table is NOT busy
2018-10-15 15:25:35,181 Starting flashes...
2018-10-15 15:25:38,231 Stopping flashes...
2018-10-15 15:25:39,283 Moving to position 2
2018-10-15 15:25:39,283 Selecting XY table position: 2
2018-10-15 15:25:39,285 Moving to next XY table position
2018-10-15 15:25:40,392 XY table IS busy
2018-10-15 15:25:48,504 XY table is NOT busy
2018-10-15 15:25:58,513 Starting flashes...
2018-10-15 15:26:01,565 Stopping flashes...
2018-10-15 15:26:02,616 Moving to parking position
2018-10-15 15:26:02,618 Exiting scan mode
2018-10-15 15:26:02,620 Moving to next XY table position
2018-10-15 15:26:27,038 XY table IS parked
2018-10-15 15:26:27,059 Scan took 0:15:00.480514
15:26 - Stopping TIB...
15:26 - Status: TibState.Running
15:26 - Alarms: AlarmVector.ReadError
15:26 - Connection status: True
15:26 - Disabling trigger
15:26 - Disabling PPS
15:26 - Status: TibState.PpsStopped
15:26 - Alarms: AlarmVector.ReadError
15:26 - Connection status: True
15:26 - Closing TIB connection to camera server
15:26 - Status: TibState.PpsStopped
15:26 - Alarms: AlarmVector.ReadError
15:26 - Connection status: False
15:26 - Run duration: 0:15:43
15:26 - Local camera triggers: 0
15:26 - Slow control triggers: 0
15:26 - Single photo-electron triggers: 0
15:26 - Calibration triggers: 53400
15:26 - Software triggers from UCTS: 0
15:26 - Pedestal triggers: 0
15:26 - Collected input triggers: 53400
15:26 - Busy triggers: 0
15:26 - Camera event triggers sent to clusters: 53400