11:07 - Setting HVPA ramp sped to 20 V/s
11:07 - Switching HVPA to state Nominal
11:07 - Switching drawer 128 HVPA to state Nominal
11:07 - Checking high voltages...
11:07 - Starting task "Check HV"
11:07 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
11:07 - Done
11:07 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:07 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 38.43 V and 74.42 V.
11:07 - Maximum difference between expected and actual voltages in drawer 128 is 956.87 V
11:07 - Checking status of HVPA module in 1 drawer(s)...
11:07 - Checking status of HVPA channels in 1 drawer(s)...
11:07 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
11:07 - Finished task "Check HV"
11:08 - Configuring calibration box...
11:08 - Configuring calibration box with leds=0x800 voltage=9.50 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
11:08 - Configuring TIB...
11:08 - Setting TIB forced mode to False
11:08 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:08 - Status: TibState.PpsStopped
11:08 - Alarms: AlarmVector.ReadError
11:08 - Connection status: False
11:08 - Entering set_external_delay
11:08 - Setting ExternalDelayCalibration to 0.000 ns
11:08 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:08 - Entering set_external_delay
11:08 - Setting ExternalDelaySphe to 0.000 ns
11:08 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:08 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
11:08 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:08 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:08 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:08 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:08 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:08 - Status: TibState.PpsStopped
11:08 - Alarms: AlarmVector.ReadError
11:08 - Connection status: False
11:08 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:08 - Writing 10000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:08 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:08 - Writing 10000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:08 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:08 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:08 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:08 - Connecting TIB to camera server at 10.10.4.12:222
11:08 - Starting TIB...
11:08 - Status: TibState.PpsStopped
11:08 - Alarms: AlarmVector.ReadError
11:08 - Connection status: False
11:08 - Resetting run
11:08 - Wait for UCTS external trigger before enabling trigger...
11:08 - Status: TibState.Standby
11:08 - Alarms: AlarmVector.NoAlarm
11:08 - Connection status: False
11:08 - Status: TibState.Standby
11:08 - Alarms: AlarmVector.NoAlarm
11:08 - Connection status: False
11:08 - Status: TibState.Armed
11:08 - Alarms: AlarmVector.NoAlarm
11:08 - Connection status: True
11:08 - Starting TIB triggers...
11:08 - Enabling trigger
11:08 - Status: TibState.Running
11:08 - Alarms: AlarmVector.NoAlarm
11:08 - Connection status: True
11:08 - Checking high voltages...
11:08 - Starting task "Check HV"
11:08 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
11:08 - Reference voltage of channel 2 in drawer #128: expected 998.96, read 0.00
11:08 - Done
11:08 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:08 - Found 1 drawer(s). Reference voltage is between 0.00 V and 1010.48 V. Actual voltage is between 1.22 V and 1010.16 V.
11:08 - Maximum difference between expected and actual voltages in drawer 128 is 1.22 V
11:08 - Checking status of HVPA module in 1 drawer(s)...
11:08 - HVPA module in drawer 128 has a status of 0x7b!
11:08 - Checking status of HVPA channels in 1 drawer(s)...
11:08 - HVPA channel 2 of drawer 128 has status 0x8003!
11:08 - Resetting HVPA channel 2 of drawer 128...
11:08 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
11:08 - Finished task "Check HV"
11:09 - Enabling high voltages...
11:09 - Starting task "Enable HV"
11:09 - Setting HV to 100.0 V
11:09 - Checking status of HVPA channels in 1 drawer(s)...
11:09 - HVPA channel 2 of drawer 128 has status 0x8003!
11:09 - Resetting HVPA channel 2 of drawer 128...
11:09 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 6 channel(s)
11:09 - Setting HV to nominal values...
11:09 - Setting channel 0 voltages to [966.45]
11:09 - Setting channel 1 voltages to [1002.6]
11:09 - Setting channel 2 voltages to [998.96]
11:09 - Setting channel 3 voltages to [1001.55]
11:09 - Setting channel 4 voltages to [1010.48]
11:09 - Setting channel 5 voltages to [992.7]
11:09 - Setting channel 6 voltages to [984.57]
11:09 - Checking status of HVPA channels in 1 drawer(s)...
11:09 - HVPA channel 2 of drawer 128 has status 0x8003!
11:09 - Resetting HVPA channel 2 of drawer 128...
11:09 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 6 channel(s)
11:09 - Finished task "Enable HV"
11:09 - Checking high voltages...
11:09 - Starting task "Check HV"
11:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
11:09 - Done
11:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 248.27 V and 1010.16 V.
11:09 - Maximum difference between expected and actual voltages in drawer 128 is 745.81 V
11:09 - Checking status of HVPA module in 1 drawer(s)...
11:09 - Checking status of HVPA channels in 1 drawer(s)...
11:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
11:09 - Finished task "Check HV"
11:09 - Checking high voltages...
11:09 - Starting task "Check HV"
11:09 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
11:09 - Done
11:09 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:09 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.85 V and 1010.77 V.
11:09 - Maximum difference between expected and actual voltages in drawer 128 is 2.83 V
11:09 - Checking status of HVPA module in 1 drawer(s)...
11:09 - Checking status of HVPA channels in 1 drawer(s)...
11:09 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
11:09 - Finished task "Check HV"
11:10 - NMC is in state NmcState.Configured and knows of 1 drawer(s)
11:10 - Found 0 PPS errors.
11:10 - Checking high voltages...
11:10 - Starting task "Check HV"
11:10 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
11:10 - Done
11:10 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:10 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 965.63 V and 1010.77 V.
11:10 - Maximum difference between expected and actual voltages in drawer 128 is 0.38 V
11:10 - Checking status of HVPA module in 1 drawer(s)...
11:10 - Checking status of HVPA channels in 1 drawer(s)...
11:10 - HV is stabilized in all channels.
11:10 - Finished task "Check HV"
11:10 - Starting NMC
11:10 - Clearing PPS error counters
11:25 - Stopping TIB...
11:25 - Status: TibState.Running
11:25 - Alarms: AlarmVector.ReadError
11:25 - Connection status: True
11:25 - Disabling trigger
11:25 - Disabling PPS
11:25 - Status: TibState.PpsStopped
11:25 - Alarms: AlarmVector.ReadError
11:25 - Connection status: True
11:25 - Closing TIB connection to camera server
11:25 - Status: TibState.PpsStopped
11:25 - Alarms: AlarmVector.ReadError
11:25 - Connection status: False
11:25 - Run duration: 0:16:31
11:25 - Local camera triggers: 0
11:25 - Slow control triggers: 0
11:25 - Single photo-electron triggers: 0
11:25 - Calibration triggers: 53409
11:25 - Software triggers from UCTS: 0
11:25 - Pedestal triggers: 0
11:25 - Collected input triggers: 53409
11:25 - Busy triggers: 0
11:25 - Camera event triggers sent to clusters: 53409
11:25 - Checking high voltages...
11:25 - Starting task "Check HV"
11:25 - Checking reference voltages against /local/home/cta_test_bench/config/2018/20181015/config_1module_calib.NMC.xml
11:25 - Done
11:25 - Found 1 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:25 - Found 1 drawer(s). Reference voltage is between 966.45 V and 1010.48 V. Actual voltage is between 966.24 V and 1010.77 V.
11:25 - Maximum difference between expected and actual voltages in drawer 128 is 0.37 V
11:25 - Checking status of HVPA module in 1 drawer(s)...
11:25 - Checking status of HVPA channels in 1 drawer(s)...
11:25 - HV is stabilized in all channels.
11:25 - Finished task "Check HV"
11:25 - Stopping NMC
11:25 - Found 0 PPS errors.