14:53 - ECC is in state EccState.Ready with status EccStatus.NoError
14:53 - ECC temperature sensors: T1= 26.9, T2= 26.3, T3= 27.5, T4= 28.7 deg C
14:53 - 24 V power supply no. 1 is enabled with a current of 46.400 A.
14:54 - Stopping NMC
14:54 - Found 0 PPS errors.
14:54 - Checking high voltages...
14:54 - Starting task "Check HV"
14:54 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20181009/NectarCAM.Run0921.NMC.xml
14:54 - Done
14:54 - Found 1 drawer(s) in Nominal state, 1 in Low state and 0 in Wait state
14:54 - Found 2 drawer(s). Reference voltage is between 966.45 V and 1379.81 V. Actual voltage is between 966.24 V and 1380.43 V.
14:54 - Maximum difference between expected and actual voltages in drawer 127 is 1180.43 V
14:54 - Maximum difference between expected and actual voltages in drawer 128 is 0.37 V
14:54 - Checking status of HVPA module in 2 drawer(s)...
14:54 - Checking status of HVPA channels in 2 drawer(s)...
14:54 - HV is stabilized in all channels.
14:54 - Finished task "Check HV"
14:54 - Starting NMC
14:54 - Clearing PPS error counters
14:54 - Configuring TIB...
14:54 - Setting TIB forced mode to False
14:54 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:54 - Status: TibState.PpsStopped
14:54 - Alarms: AlarmVector.ReadError
14:54 - Connection status: False
14:54 - Entering set_external_delay
14:54 - Setting ExternalDelayCalibration to 0.000 ns
14:54 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:54 - Entering set_external_delay
14:54 - Setting ExternalDelaySphe to 0.000 ns
14:54 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:54 - Setting TIB trigger mode to 0x44 = TriggerMask.SlowControl|Calibration
14:54 - Writing 68 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:54 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:54 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:54 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:54 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:54 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:54 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:54 - Status: TibState.PpsStopped
14:54 - Alarms: AlarmVector.ReadError
14:54 - Connection status: False
14:54 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:54 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:54 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:54 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:54 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:54 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:54 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:54 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:54 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:54 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:54 - Connecting TIB to camera server at 10.10.4.12:222
14:54 - Starting TIB...
14:54 - Status: TibState.PpsStopped
14:54 - Alarms: AlarmVector.ReadError
14:54 - Connection status: False
14:54 - Resetting run
14:54 - Wait for UCTS external trigger before enabling trigger...
14:54 - Status: TibState.Standby
14:54 - Alarms: AlarmVector.NoAlarm
14:54 - Connection status: False
14:54 - Status: TibState.Standby
14:54 - Alarms: AlarmVector.NoAlarm
14:54 - Connection status: False
14:54 - Status: TibState.Armed
14:54 - Alarms: AlarmVector.NoAlarm
14:54 - Connection status: True
14:54 - Starting TIB triggers...
14:54 - Enabling trigger
14:54 - Status: TibState.Running
14:54 - Alarms: AlarmVector.NoAlarm
14:54 - Connection status: True
14:54 - Configuring calibration box...
14:54 - Configuring calibration box with leds=0x40 voltage=8.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
14:54 - Scanning voltages
14:54 - Starting task "Scan voltages"
14:54 - Setting LED mask to 0x0
14:54 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
14:54 - Starting flashes...
14:54 - Stopping flashes...
14:54 - Setting LED mask to 0x40
14:54 - Setting voltage to 8.000000 V
14:54 - Starting flashes...
14:55 - Stopping flashes...
14:55 - Setting voltage to 8.250000 V
14:55 - Starting flashes...
14:55 - Stopping flashes...
14:55 - Setting voltage to 8.500000 V
14:55 - Starting flashes...
14:55 - Stopping flashes...
14:56 - Setting voltage to 8.750000 V
14:56 - Starting flashes...
14:56 - Stopping flashes...
14:56 - Setting voltage to 9.000000 V
14:56 - Starting flashes...
14:56 - Stopping flashes...
14:56 - Setting voltage to 9.250000 V
14:56 - Starting flashes...
14:56 - Stopping flashes...
14:57 - Setting voltage to 9.500000 V
14:57 - Starting flashes...
14:57 - Stopping flashes...
14:57 - Setting voltage to 9.750000 V
14:57 - Starting flashes...
14:57 - Stopping flashes...
14:58 - Setting voltage to 10.000000 V
14:58 - Starting flashes...
14:58 - Stopping flashes...
14:58 - Setting voltage to 10.250000 V
14:58 - Starting flashes...
14:58 - Stopping flashes...
14:58 - Setting voltage to 10.500000 V
14:58 - Starting flashes...
14:58 - Stopping flashes...
14:59 - Setting voltage to 10.750000 V
14:59 - Starting flashes...
14:59 - Stopping flashes...
14:59 - Setting voltage to 11.000000 V
14:59 - Starting flashes...
14:59 - Stopping flashes...
14:59 - Setting voltage to 11.250000 V
14:59 - Starting flashes...
15:00 - Stopping flashes...
15:00 - Setting voltage to 11.500000 V
15:00 - Starting flashes...
15:00 - Stopping flashes...
15:00 - Setting voltage to 11.750000 V
15:00 - Starting flashes...
15:00 - Stopping flashes...
15:01 - Setting voltage to 12.000000 V
15:01 - Starting flashes...
15:01 - Stopping flashes...
15:01 - Setting voltage to 12.250000 V
15:01 - Starting flashes...
15:01 - Stopping flashes...
15:01 - Setting voltage to 12.500000 V
15:01 - Starting flashes...
15:02 - Stopping flashes...
15:02 - Setting voltage to 12.750000 V
15:02 - Starting flashes...
15:02 - Stopping flashes...
15:02 - Setting voltage to 13.000000 V
15:02 - Starting flashes...
15:02 - Stopping flashes...
15:03 - Setting voltage to 13.250000 V
15:03 - Starting flashes...
15:03 - Stopping flashes...
15:03 - Setting voltage to 13.500000 V
15:03 - Starting flashes...
15:03 - Stopping flashes...
15:03 - Setting voltage to 13.750000 V
15:03 - Starting flashes...
15:03 - Stopping flashes...
15:04 - Setting voltage to 14.000000 V
15:04 - Starting flashes...
15:04 - Stopping flashes...
15:04 - Setting voltage to 14.250000 V
15:04 - Starting flashes...
15:04 - Stopping flashes...
15:05 - Setting voltage to 14.500000 V
15:05 - Starting flashes...
15:05 - Stopping flashes...
15:05 - Setting voltage to 14.750000 V
15:05 - Starting flashes...
15:05 - Stopping flashes...
15:05 - Setting voltage to 15.000000 V
15:05 - Starting flashes...
15:05 - Stopping flashes...
15:06 - Setting voltage to 15.250000 V
15:06 - Starting flashes...
15:06 - Stopping flashes...
15:06 - Setting voltage to 15.500000 V
15:06 - Starting flashes...
15:06 - Stopping flashes...
15:06 - Setting voltage to 15.750000 V
15:06 - Starting flashes...
15:07 - Stopping flashes...
15:07 - Setting voltage to 16.000000 V
15:07 - Starting flashes...
15:07 - Stopping flashes...
15:07 - Finished task "Scan voltages"
15:08 - Stopping TIB...
15:08 - Status: TibState.Running
15:08 - Alarms: AlarmVector.ReadError
15:08 - Connection status: True
15:08 - Disabling trigger
15:08 - Disabling PPS
15:08 - Status: TibState.PpsStopped
15:08 - Alarms: AlarmVector.ReadError
15:08 - Connection status: True
15:08 - Closing TIB connection to camera server
15:08 - Status: TibState.PpsStopped
15:08 - Alarms: AlarmVector.ReadError
15:08 - Connection status: False
15:08 - Run duration: 0:13:53
15:08 - Local camera triggers: 0
15:08 - Slow control triggers: 0
15:08 - Single photo-electron triggers: 0
15:08 - Calibration triggers: 205835
15:08 - Software triggers from UCTS: 0
15:08 - Pedestal triggers: 0
15:08 - Collected input triggers: 205835
15:08 - Busy triggers: 0
15:08 - Camera event triggers sent to clusters: 205835