12:22 - Checking high voltages...
12:22 - Starting task "Check HV"
12:22 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180524/NectarCAM.Run0830.NMC.xml
12:22 - Done
12:22 - Found 6 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 0.00 V and 1227.32 V.
12:22 - Maximum difference between reference and actual voltage is 1141.08 V
12:22 - Checking status of HVPA module in 6 drawer(s)...
12:23 - Checking status of HVPA channels in 6 drawer(s)...
12:23 - HV is stabilized in all channels.
12:23 - Finished task "Check HV"
12:23 - Disabling high voltages...
12:23 - Starting task "Disable HV"
12:23 - Check of HVPA failed: expected 0.00, read 1103.39
12:23 - Check of HVPA failed: expected 0.00, read 1096.76
12:23 - Check of HVPA failed: expected 0.00, read 1128.07
12:23 - Maximum reference voltage is now 0.00 V
12:23 - Finished task "Disable HV"
12:24 - Checking high voltages...
12:24 - Starting task "Check HV"
12:24 - Checking reference voltages against 0.000000 V
12:24 - Done
12:24 - Found 6 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 0.00 V and 229.36 V.
12:24 - Maximum difference between reference and actual voltage is 226.92 V
12:24 - Checking status of HVPA module in 6 drawer(s)...
12:24 - HVPA module in drawer 150 has a status of 0x77!
12:24 - Checking status of HVPA channels in 6 drawer(s)...
12:24 - HVPA channel 3 of drawer 150 has status 0x8001!
12:24 - Resetting HVPA channel 3 of drawer 150...
12:24 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
12:24 - Finished task "Check HV"
12:24 - Resetting NMC
12:24 - Executing command '/opt/taxi/bin/cta_power --slot 3 --channel 11 --off' on Digital Trigger Crate at 10.10.0.199
12:25 - Executing command '/opt/taxi/bin/cta_power --slot 3 --channel 13 --off' on Digital Trigger Crate at 10.10.0.199
12:26 - Starting task "Configure NMC"
12:26 - Configuring modules with configuration /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:26 - Could not invoke the MethodCall service: BadTimeout
12:26 - NMC is in state NmcState.Ready and knows of 0 drawer(s)
12:26 - Found 0 PPS errors.
12:26 - Finished task "Configure NMC"
12:27 - Starting task "Configure NMC"
12:27 - Configuring modules with configuration /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:27 - NMC is in state NmcState.Configured and knows of 4 drawer(s)
12:27 - Found 0 PPS errors.
12:27 - Finished task "Configure NMC"
12:27 - Checking high voltages...
12:27 - Starting task "Check HV"
12:27 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:27 - Done
12:27 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 112.85 V and 1159.61 V.
12:27 - Maximum difference between reference and actual voltage is 1017.39 V
12:27 - Checking status of HVPA module in 4 drawer(s)...
12:27 - HVPA module in drawer 114 has a status of 0x6f!
12:27 - Checking status of HVPA channels in 4 drawer(s)...
12:27 - HVPA channel 4 of drawer 114 has status 0x8001!
12:27 - Resetting HVPA channel 4 of drawer 114...
12:27 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 13 channel(s)
12:27 - Finished task "Check HV"
12:27 - Enabling high voltages...
12:27 - Starting task "Enable HV"
12:27 - Setting HV to 100.0 V
12:27 - Check of HVPA failed: expected 100.00, read 1164.29
12:27 - Check of HVPA failed: expected 100.00, read 1128.07
12:27 - Check of HVPA failed: expected 100.00, read 1179.65
12:27 - Checking status of HVPA channels in 4 drawer(s)...
12:27 - HVPA channel 4 of drawer 114 has status 0x8001!
12:27 - Resetting HVPA channel 4 of drawer 114...
12:27 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:27 - Setting HV to nominal values...
12:27 - Setting channel 0 voltages to [1092.65, 1154.16, 1078.12, 951.32]
12:27 - Setting channel 1 voltages to [1117.69, 1164.29, 1104.93, 993.09]
12:27 - Setting channel 2 voltages to [1061.26, 1158.46, 1075.89, 988.47]
12:27 - Setting channel 3 voltages to [1158.14, 1119.57, 1145.38, 982.15]
12:27 - Setting channel 4 voltages to [1128.07, 1166.64, 1184.94, 988.76]
12:27 - Setting channel 5 voltages to [1171.44, 1179.65, 1190.92, 971.32]
12:27 - Setting channel 6 voltages to [1102.07, 1097.92, 1227.22, 969.17]
12:27 - Checking status of HVPA channels in 4 drawer(s)...
12:27 - HVPA channel 4 of drawer 114 has status 0x8001!
12:27 - Resetting HVPA channel 4 of drawer 114...
12:27 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
12:27 - Finished task "Enable HV"
12:27 - Checking high voltages...
12:27 - Starting task "Check HV"
12:27 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:27 - Done
12:27 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 107.36 V and 1227.93 V.
12:27 - Maximum difference between reference and actual voltage is 1020.71 V
12:27 - Checking status of HVPA module in 4 drawer(s)...
12:27 - HVPA module in drawer 114 has a status of 0x6f!
12:27 - Checking status of HVPA channels in 4 drawer(s)...
12:27 - HVPA channel 4 of drawer 114 has status 0x8001!
12:27 - Resetting HVPA channel 4 of drawer 114...
12:27 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 5 channel(s)
12:27 - Finished task "Check HV"
12:27 - Enabling high voltages...
12:27 - Starting task "Enable HV"
12:27 - Setting HV to 100.0 V
12:27 - Check of HVPA failed: expected 100.00, read 1104.93
12:27 - Check of HVPA failed: expected 100.00, read 1104.93
12:27 - Check of HVPA failed: expected 100.00, read 982.15
12:27 - Check of HVPA failed: expected 100.00, read 1166.64
12:27 - Checking status of HVPA channels in 4 drawer(s)...
12:27 - HVPA channel 4 of drawer 114 has status 0x8001!
12:27 - Resetting HVPA channel 4 of drawer 114...
12:27 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:27 - Setting HV to nominal values...
12:27 - Setting channel 0 voltages to [1092.65, 1154.16, 1078.12, 951.32]
12:27 - Setting channel 1 voltages to [1117.69, 1164.29, 1104.93, 993.09]
12:27 - Setting channel 2 voltages to [1061.26, 1158.46, 1075.89, 988.47]
12:27 - Setting channel 3 voltages to [1158.14, 1119.57, 1145.38, 982.15]
12:27 - Setting channel 4 voltages to [1128.07, 1166.64, 1184.94, 988.76]
12:27 - Setting channel 5 voltages to [1171.44, 1179.65, 1190.92, 971.32]
12:27 - Setting channel 6 voltages to [1102.07, 1097.92, 1227.22, 969.17]
12:27 - Checking status of HVPA channels in 4 drawer(s)...
12:27 - HVPA channel 4 of drawer 114 has status 0x8001!
12:27 - Resetting HVPA channel 4 of drawer 114...
12:27 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 10 channel(s)
12:27 - Check of 'NectarFrontEnd_115.Hvpa.Hvpa2.Voltage' failed: expected 1158.46, read 100
12:27 - Finished task "Enable HV"
12:27 - Checking high voltages...
12:27 - Starting task "Check HV"
12:27 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:27 - Done
12:27 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 101.87 V and 1228.54 V.
12:27 - Maximum difference between reference and actual voltage is 1026.20 V
12:27 - Checking status of HVPA module in 4 drawer(s)...
12:27 - HVPA module in drawer 114 has a status of 0x6f!
12:27 - Checking status of HVPA channels in 4 drawer(s)...
12:27 - HVPA channel 4 of drawer 114 has status 0x8001!
12:27 - Resetting HVPA channel 4 of drawer 114...
12:27 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 5 channel(s)
12:27 - Finished task "Check HV"
12:28 - Enabling high voltages...
12:28 - Starting task "Enable HV"
12:28 - Setting HV to 100.0 V
12:28 - Check of HVPA failed: expected 100.00, read 1145.38
12:28 - Check of HVPA failed: expected 100.00, read 1184.94
12:28 - Checking status of HVPA channels in 4 drawer(s)...
12:28 - HVPA channel 4 of drawer 114 has status 0x8001!
12:28 - Resetting HVPA channel 4 of drawer 114...
12:28 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:28 - Setting HV to nominal values...
12:28 - Setting channel 0 voltages to [1092.65, 1154.16, 1078.12, 951.32]
12:28 - Setting channel 1 voltages to [1117.69, 1164.29, 1104.93, 993.09]
12:28 - Setting channel 2 voltages to [1061.26, 1158.46, 1075.89, 988.47]
12:28 - Setting channel 3 voltages to [1158.14, 1119.57, 1145.38, 982.15]
12:28 - Setting channel 4 voltages to [1128.07, 1166.64, 1184.94, 988.76]
12:28 - Setting channel 5 voltages to [1171.44, 1179.65, 1190.92, 971.32]
12:28 - Setting channel 6 voltages to [1102.07, 1097.92, 1227.22, 969.17]
12:28 - Checking status of HVPA channels in 4 drawer(s)...
12:28 - HVPA channel 4 of drawer 114 has status 0x8001!
12:28 - Resetting HVPA channel 4 of drawer 114...
12:28 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 4 channel(s)
12:28 - Finished task "Enable HV"
12:28 - Checking high voltages...
12:28 - Starting task "Check HV"
12:28 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:28 - Done
12:28 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 96.38 V and 1227.32 V.
12:28 - Maximum difference between reference and actual voltage is 1031.69 V
12:28 - Checking status of HVPA module in 4 drawer(s)...
12:28 - HVPA module in drawer 114 has a status of 0x6f!
12:28 - Checking status of HVPA channels in 4 drawer(s)...
12:28 - HVPA channel 4 of drawer 114 has status 0x8001!
12:28 - Resetting HVPA channel 4 of drawer 114...
12:28 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
12:28 - Finished task "Check HV"
12:28 - Enabling high voltages...
12:28 - Starting task "Enable HV"
12:28 - Setting HV to 100.0 V
12:28 - Check of HVPA failed: expected 100.00, read 1154.16
12:28 - Check of HVPA failed: expected 100.00, read 1158.14
12:28 - Check of HVPA failed: expected 100.00, read 1171.44
12:28 - Checking status of HVPA channels in 4 drawer(s)...
12:28 - HVPA channel 4 of drawer 114 has status 0x8001!
12:28 - Resetting HVPA channel 4 of drawer 114...
12:28 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:28 - Setting HV to nominal values...
12:28 - Setting channel 0 voltages to [1092.65, 1154.16, 1078.12, 951.32]
12:28 - Setting channel 1 voltages to [1117.69, 1164.29, 1104.93, 993.09]
12:28 - Setting channel 2 voltages to [1061.26, 1158.46, 1075.89, 988.47]
12:28 - Setting channel 3 voltages to [1158.14, 1119.57, 1145.38, 982.15]
12:28 - Setting channel 4 voltages to [1128.07, 1166.64, 1184.94, 988.76]
12:28 - Setting channel 5 voltages to [1171.44, 1179.65, 1190.92, 971.32]
12:28 - Setting channel 6 voltages to [1102.07, 1097.92, 1227.22, 969.17]
12:28 - Checking status of HVPA channels in 4 drawer(s)...
12:28 - HVPA channel 4 of drawer 114 has status 0x8001!
12:28 - Resetting HVPA channel 4 of drawer 114...
12:28 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 3 channel(s)
12:28 - Finished task "Enable HV"
12:28 - Checking high voltages...
12:28 - Starting task "Check HV"
12:28 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:28 - Done
12:28 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 91.50 V and 1227.93 V.
12:28 - Maximum difference between reference and actual voltage is 1036.57 V
12:28 - Checking status of HVPA module in 4 drawer(s)...
12:28 - HVPA module in drawer 114 has a status of 0x6f!
12:28 - Checking status of HVPA channels in 4 drawer(s)...
12:28 - HVPA channel 4 of drawer 114 has status 0x8001!
12:28 - Resetting HVPA channel 4 of drawer 114...
12:28 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
12:28 - Finished task "Check HV"
12:29 - Enabling high voltages...
12:29 - Starting task "Enable HV"
12:29 - Setting HV to 100.0 V
12:29 - Check of HVPA failed: expected 100.00, read 1117.69
12:29 - Check of HVPA failed: expected 100.00, read 971.32
12:29 - Checking status of HVPA channels in 4 drawer(s)...
12:29 - HVPA channel 4 of drawer 114 has status 0x8001!
12:29 - Resetting HVPA channel 4 of drawer 114...
12:29 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:29 - Setting HV to nominal values...
12:29 - Setting channel 0 voltages to [1092.65, 1154.16, 1078.12, 951.32]
12:29 - Setting channel 1 voltages to [1117.69, 1164.29, 1104.93, 993.09]
12:29 - Setting channel 2 voltages to [1061.26, 1158.46, 1075.89, 988.47]
12:29 - Setting channel 3 voltages to [1158.14, 1119.57, 1145.38, 982.15]
12:29 - Setting channel 4 voltages to [1128.07, 1166.64, 1184.94, 988.76]
12:29 - Setting channel 5 voltages to [1171.44, 1179.65, 1190.92, 971.32]
12:29 - Setting channel 6 voltages to [1102.07, 1097.92, 1227.22, 969.17]
12:29 - Checking status of HVPA channels in 4 drawer(s)...
12:29 - HVPA channel 4 of drawer 114 has status 0x8001!
12:29 - Resetting HVPA channel 4 of drawer 114...
12:29 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 3 channel(s)
12:29 - Finished task "Enable HV"
12:29 - Checking high voltages...
12:29 - Starting task "Check HV"
12:29 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:29 - Reference voltage of channel 1 in drawer #149: expected 993.09, read 995.32
12:29 - Done
12:29 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 82.96 V and 1227.32 V.
12:29 - Maximum difference between reference and actual voltage is 1045.72 V
12:29 - Checking status of HVPA module in 4 drawer(s)...
12:29 - HVPA module in drawer 114 has a status of 0x6f!
12:29 - Checking status of HVPA channels in 4 drawer(s)...
12:29 - HVPA channel 4 of drawer 114 has status 0x8001!
12:29 - Resetting HVPA channel 4 of drawer 114...
12:29 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
12:29 - Finished task "Check HV"
12:31 - Disabling high voltages...
12:31 - Starting task "Disable HV"
12:31 - Check of HVPA failed: expected 0.00, read 951.32
12:31 - Check of HVPA failed: expected 0.00, read 988.47
12:31 - Check of HVPA failed: expected 0.00, read 988.47
12:31 - Check of HVPA failed: expected 0.00, read 988.47
12:31 - Check of HVPA failed: expected 0.00, read 988.47
12:31 - Maximum reference voltage is now 0.00 V
12:31 - Finished task "Disable HV"
12:31 - Checking high voltages...
12:31 - Starting task "Check HV"
12:31 - Checking reference voltages against 0.000000 V
12:31 - Done
12:31 - Found 4 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 56.12 V and 996.13 V.
12:31 - Maximum difference between reference and actual voltage is 980.88 V
12:31 - Checking status of HVPA module in 4 drawer(s)...
12:31 - HVPA module in drawer 114 has a status of 0x00!
12:31 - Checking status of HVPA channels in 4 drawer(s)...
12:31 - HVPA channel 0 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 0 of drawer 114...
12:31 - HVPA channel 1 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 1 of drawer 114...
12:31 - HVPA channel 2 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 2 of drawer 114...
12:31 - HVPA channel 5 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 5 of drawer 114...
12:31 - HVPA channel 6 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 6 of drawer 114...
12:31 - HV was locked in 5 channel(s), was in rise default in 0 channel(s) and was still in progress in 21 channel(s)
12:31 - Finished task "Check HV"
12:31 - Checking high voltages...
12:31 - Starting task "Check HV"
12:31 - Checking reference voltages against 0.000000 V
12:31 - Done
12:31 - Found 4 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 55.51 V and 853.39 V.
12:31 - Maximum difference between reference and actual voltage is 843.02 V
12:31 - Checking status of HVPA module in 4 drawer(s)...
12:31 - HVPA module in drawer 114 has a status of 0x18!
12:31 - Checking status of HVPA channels in 4 drawer(s)...
12:31 - HVPA channel 0 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 0 of drawer 114...
12:31 - HVPA channel 1 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 1 of drawer 114...
12:31 - HVPA channel 2 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 2 of drawer 114...
12:31 - HVPA channel 5 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 5 of drawer 114...
12:31 - HVPA channel 6 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 6 of drawer 114...
12:31 - HV was locked in 5 channel(s), was in rise default in 0 channel(s) and was still in progress in 21 channel(s)
12:31 - Finished task "Check HV"
12:31 - Checking high voltages...
12:31 - Starting task "Check HV"
12:31 - Checking reference voltages against 0.000000 V
12:31 - Done
12:31 - Found 4 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 54.90 V and 643.55 V.
12:31 - Maximum difference between reference and actual voltage is 636.84 V
12:31 - Checking status of HVPA module in 4 drawer(s)...
12:31 - HVPA module in drawer 114 has a status of 0x18!
12:31 - Checking status of HVPA channels in 4 drawer(s)...
12:31 - HVPA channel 0 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 0 of drawer 114...
12:31 - HVPA channel 1 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 1 of drawer 114...
12:31 - HVPA channel 2 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 2 of drawer 114...
12:31 - HVPA channel 5 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 5 of drawer 114...
12:31 - HVPA channel 6 of drawer 114 has status 0x8001!
12:31 - Resetting HVPA channel 6 of drawer 114...
12:31 - HV was locked in 5 channel(s), was in rise default in 0 channel(s) and was still in progress in 20 channel(s)
12:31 - Finished task "Check HV"
12:31 - Checking high voltages...
12:31 - Starting task "Check HV"
12:31 - Checking reference voltages against 0.000000 V
12:31 - Done
12:32 - Found 4 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 54.29 V and 578.89 V.
12:32 - Maximum difference between reference and actual voltage is 572.79 V
12:32 - Checking status of HVPA module in 4 drawer(s)...
12:32 - HVPA module in drawer 114 has a status of 0x18!
12:32 - Checking status of HVPA channels in 4 drawer(s)...
12:32 - HVPA channel 0 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 0 of drawer 114...
12:32 - HVPA channel 1 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 1 of drawer 114...
12:32 - HVPA channel 2 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 2 of drawer 114...
12:32 - HVPA channel 5 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 5 of drawer 114...
12:32 - HVPA channel 6 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 6 of drawer 114...
12:32 - HV was locked in 5 channel(s), was in rise default in 0 channel(s) and was still in progress in 6 channel(s)
12:32 - Finished task "Check HV"
12:32 - Checking high voltages...
12:32 - Starting task "Check HV"
12:32 - Checking reference voltages against 0.000000 V
12:32 - Done
12:32 - Found 4 drawer(s). Reference voltage is between 0.00 V and 0.00 V. Actual voltage is between 53.07 V and 473.97 V.
12:32 - Maximum difference between reference and actual voltage is 469.70 V
12:32 - Checking status of HVPA module in 4 drawer(s)...
12:32 - HVPA module in drawer 114 has a status of 0x18!
12:32 - Checking status of HVPA channels in 4 drawer(s)...
12:32 - HVPA channel 0 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 0 of drawer 114...
12:32 - HVPA channel 1 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 1 of drawer 114...
12:32 - HVPA channel 2 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 2 of drawer 114...
12:32 - HVPA channel 5 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 5 of drawer 114...
12:32 - HVPA channel 6 of drawer 114 has status 0x8001!
12:32 - Resetting HVPA channel 6 of drawer 114...
12:32 - HV was locked in 5 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
12:32 - Finished task "Check HV"
12:34 - Starting task "Configure NMC"
12:34 - Configuring modules with configuration /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - NMC is in state NmcState.Configured and knows of 4 drawer(s)
12:35 - Found 0 PPS errors.
12:35 - Finished task "Configure NMC"
12:35 - Checking high voltages...
12:35 - Starting task "Check HV"
12:35 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - Reference voltage of channel 1 in drawer #116: expected 1104.93, read 0.00
12:35 - Reference voltage of channel 2 in drawer #116: expected 1075.89, read 0.00
12:35 - Reference voltage of channel 3 in drawer #116: expected 1145.38, read 0.00
12:35 - Reference voltage of channel 5 in drawer #116: expected 1190.92, read 0.00
12:35 - Done
12:35 - Found 4 drawer(s). Reference voltage is between 0.00 V and 1227.22 V. Actual voltage is between 0.00 V and 128.71 V.
12:35 - Maximum difference between reference and actual voltage is 1171.44 V
12:35 - Checking status of HVPA module in 4 drawer(s)...
12:35 - HVPA module in drawer 114 has a status of 0x08!
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HVPA channel 0 of drawer 114 has status 0x8001!
12:35 - Resetting HVPA channel 0 of drawer 114...
12:35 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 21 channel(s)
12:35 - Finished task "Check HV"
12:35 - Enabling high voltages...
12:35 - Starting task "Enable HV"
12:35 - Setting HV to 100.0 V
12:35 - Check of HVPA failed: expected 100.00, read 1117.69
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HVPA channel 4 of drawer 114 has status 0x8001!
12:35 - Resetting HVPA channel 4 of drawer 114...
12:35 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:35 - Setting HV to nominal values...
12:35 - Setting channel 0 voltages to [1092.65, 1154.16, 1078.12, 951.32]
12:35 - Setting channel 1 voltages to [1117.69, 1164.29, 1104.93, 993.09]
12:35 - Setting channel 2 voltages to [1061.26, 1158.46, 1075.89, 988.47]
12:35 - Setting channel 3 voltages to [1158.14, 1119.57, 1145.38, 982.15]
12:35 - Setting channel 4 voltages to [1128.07, 1166.64, 1184.94, 988.76]
12:35 - Setting channel 5 voltages to [1171.44, 1179.65, 1190.92, 971.32]
12:35 - Setting channel 6 voltages to [1102.07, 1097.92, 1227.22, 969.17]
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HVPA channel 3 of drawer 116 has status 0x8001!
12:35 - Resetting HVPA channel 3 of drawer 116...
12:35 - HVPA channel 4 of drawer 114 has status 0x8001!
12:35 - Resetting HVPA channel 4 of drawer 114...
12:35 - HV was locked in 2 channel(s), was in rise default in 0 channel(s) and was still in progress in 26 channel(s)
12:35 - Check of 'NectarFrontEnd_149.Hvpa.Hvpa1.Voltage' failed: expected 993.09, read 100
12:35 - Finished task "Enable HV"
12:35 - Checking high voltages...
12:35 - Starting task "Check HV"
12:35 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - Done
12:35 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.22 V and 627.08 V.
12:35 - Maximum difference between reference and actual voltage is 1126.85 V
12:35 - Checking status of HVPA module in 4 drawer(s)...
12:35 - HVPA module in drawer 114 has a status of 0x6f!
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HVPA channel 4 of drawer 114 has status 0x8001!
12:35 - Resetting HVPA channel 4 of drawer 114...
12:35 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:35 - Finished task "Check HV"
12:35 - Checking high voltages...
12:35 - Starting task "Check HV"
12:35 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - Done
12:35 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.22 V and 746.64 V.
12:35 - Maximum difference between reference and actual voltage is 1126.24 V
12:35 - Checking status of HVPA module in 4 drawer(s)...
12:35 - HVPA module in drawer 114 has a status of 0x6f!
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HVPA channel 4 of drawer 114 has status 0x8001!
12:35 - Resetting HVPA channel 4 of drawer 114...
12:35 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:35 - Finished task "Check HV"
12:35 - Checking high voltages...
12:35 - Starting task "Check HV"
12:35 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - Done
12:35 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.22 V and 820.45 V.
12:35 - Maximum difference between reference and actual voltage is 1126.85 V
12:35 - Checking status of HVPA module in 4 drawer(s)...
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:35 - Finished task "Check HV"
12:35 - Checking high voltages...
12:35 - Starting task "Check HV"
12:35 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - Done
12:35 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.83 V and 900.97 V.
12:35 - Maximum difference between reference and actual voltage is 1126.85 V
12:35 - Checking status of HVPA module in 4 drawer(s)...
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 27 channel(s)
12:35 - Finished task "Check HV"
12:35 - Checking high voltages...
12:35 - Starting task "Check HV"
12:35 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - Done
12:35 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.83 V and 1028.46 V.
12:35 - Maximum difference between reference and actual voltage is 1126.85 V
12:35 - Checking status of HVPA module in 4 drawer(s)...
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 24 channel(s)
12:35 - Finished task "Check HV"
12:35 - Checking high voltages...
12:35 - Starting task "Check HV"
12:35 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:35 - Done
12:35 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.22 V and 1227.32 V.
12:35 - Maximum difference between reference and actual voltage is 1126.24 V
12:35 - Checking status of HVPA module in 4 drawer(s)...
12:35 - Checking status of HVPA channels in 4 drawer(s)...
12:35 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 7 channel(s)
12:35 - Finished task "Check HV"
12:36 - Checking high voltages...
12:36 - Starting task "Check HV"
12:36 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:36 - Done
12:36 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.83 V and 1228.54 V.
12:36 - Maximum difference between reference and actual voltage is 1126.85 V
12:36 - Checking status of HVPA module in 4 drawer(s)...
12:36 - Checking status of HVPA channels in 4 drawer(s)...
12:36 - HV was locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 3 channel(s)
12:36 - Finished task "Check HV"
12:36 - Checking high voltages...
12:36 - Starting task "Check HV"
12:36 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:36 - Done
12:36 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.83 V and 1227.93 V.
12:36 - Maximum difference between reference and actual voltage is 1126.24 V
12:36 - Checking status of HVPA module in 4 drawer(s)...
12:36 - Checking status of HVPA channels in 4 drawer(s)...
12:36 - HV is stabilized in all channels.
12:36 - Finished task "Check HV"
12:36 - Checking high voltages...
12:36 - Starting task "Check HV"
12:36 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180529/config_4modules_SPE.NMC.xml
12:36 - Done
12:36 - Found 4 drawer(s). Reference voltage is between 951.32 V and 1227.22 V. Actual voltage is between 1.22 V and 1228.54 V.
12:36 - Maximum difference between reference and actual voltage is 1126.85 V
12:36 - Checking status of HVPA module in 4 drawer(s)...
12:36 - Checking status of HVPA channels in 4 drawer(s)...
12:36 - HV is stabilized in all channels.
12:36 - Finished task "Check HV"
12:37 - Starting NMC
12:37 - Clearing PPS error counters
12:37 - Configuring TIB...
12:37 - Setting TIB forced mode to False
12:37 - Writing False to serveur.TIB.Forced.ForcedMode.ForcedMode_v
12:37 - Status: TibState.RunStopped
12:37 - Alarms: AlarmVector.NoAlarm
12:37 - Disabling PPS
12:37 - Status: TibState.PpsStopped
12:37 - Alarms: AlarmVector.NoAlarm
12:37 - Writing 0.0 to serveur.TIB.ExternalDelay.ExternalDelay_v
12:37 - Setting TIB trigger mode to 0x8 = TriggerMask.SPhE
12:37 - Writing 8 to serveur.TIB.TriggerMode.ModeMask.ModeMask_v
12:37 - Writing 0 to serveur.TIB.InputsEnable.InputMask.InputMask_v
12:37 - Writing False to serveur.TIB.BUSY.DisableBusy.DisableBusy_v
12:37 - Writing 0.0 to serveur.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
12:37 - Writing False to serveur.TIB.Throttler.DisableThrottlerBP.DisableThrottlerBP_v
12:37 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP50us.MaxTriggersBP50us_v
12:37 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP1ms.MaxTriggersBP1ms_v
12:37 - Writing False to serveur.TIB.Throttler.DisableThrottlerWR.DisableThrottlerWR_v
12:37 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR50us.MaxTriggersWR50us_v
12:37 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR1ms.MaxTriggersWR1ms_v
12:37 - Status: TibState.PpsStopped
12:37 - Alarms: AlarmVector.NoAlarm
12:38 - Closing TIB connection to camera server
12:38 - Connecting TIB to camera server at 10.10.0.251:222
12:38 - Starting TIB...
12:38 - Status: TibState.PpsStopped
12:38 - Alarms: AlarmVector.NoAlarm
12:38 - Resetting run
12:38 - Wait for UCTS external trigger before enabling trigger...
12:38 - Status: TibState.Standby
12:38 - Alarms: AlarmVector.NoAlarm
12:38 - Status: TibState.Standby
12:38 - Alarms: AlarmVector.NoAlarm
12:38 - Status: TibState.CoutingPps
12:38 - Alarms: AlarmVector.NoAlarm
12:38 - Starting TIB triggers...
12:38 - Enabling trigger
12:38 - Status: TibState.Running
12:38 - Alarms: AlarmVector.NoAlarm
12:38 - Configuring calibration box...
12:38 - Configuring calibration box with leds=0x40 voltage=9.75 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
12:38 - Scanning voltages
12:38 - Starting task "Scan voltages"
12:38 - Setting LED mask to 0x0
12:38 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
12:38 - Starting flashes...
12:38 - Stopping flashes...
12:38 - Setting LED mask to 0x40
12:39 - Setting voltage to 8.000000 V
12:39 - Starting flashes...
12:39 - Stopping flashes...
12:39 - Setting voltage to 9.000000 V
12:39 - Starting flashes...
12:39 - Stopping flashes...
12:39 - Setting voltage to 10.000000 V
12:39 - Starting flashes...
12:40 - Stopping flashes...
12:40 - Setting voltage to 11.000000 V
12:40 - Starting flashes...
12:40 - Stopping flashes...
12:40 - Setting voltage to 12.000000 V
12:40 - Starting flashes...
12:40 - Stopping flashes...
12:41 - Setting voltage to 13.000000 V
12:41 - Starting flashes...
12:41 - Stopping flashes...
12:41 - Setting voltage to 14.000000 V
12:41 - Starting flashes...
12:41 - Stopping flashes...
12:41 - Setting voltage to 15.000000 V
12:41 - Starting flashes...
12:42 - Stopping flashes...
12:42 - Setting voltage to 16.000000 V
12:42 - Starting flashes...
12:42 - Stopping flashes...
12:42 - Finished task "Scan voltages"
12:43 - Stopping TIB...
12:43 - Status: TibState.Running
12:43 - Alarms: AlarmVector.NoAlarm
12:43 - Disabling trigger
12:43 - Disabling PPS
12:43 - Status: TibState.PpsStopped
12:43 - Alarms: AlarmVector.NoAlarm
12:43 - Closing TIB connection to camera server
12:43 - Status: TibState.PpsStopped
12:43 - Alarms: AlarmVector.NoAlarm
12:43 - Run duration: 0:04:53
12:43 - Local camera triggers: 0
12:43 - Slow control triggers: 0
12:43 - Single photo-electron triggers: 11077
12:43 - Calibration triggers: 0
12:43 - Software triggers from UCTS: 0
12:43 - Auto-pedestal triggers: 1904898
12:43 - Collected input triggers: 11078
12:43 - Busy triggers: 0
12:43 - Non-busy triggers sent to UCTS: 11078
12:43 - Camera event triggers sent to clusters: 11078
12:43 - Stopping NMC
12:43 - Found 0 PPS errors.