08:49 - Checking high voltages...
08:49 - Starting task "Check HV"
08:49 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
08:49 - Done
08:49 - Found 11 drawer(s). Reference voltage is between 0.00 V and 1223.41 V. Actual voltage is between 0.00 V and 1223.66 V.
08:49 - Maximum difference between reference and actual voltage is 3.22 V
08:49 - Checking status of HVPA module in 11 drawer(s)...
08:49 - Checking status of HVPA channels in 11 drawer(s)...
08:49 - HV is stabilized in all channels.
08:49 - Finished task "Check HV"
08:49 - Enabling high voltages...
08:49 - Starting task "Enable HV"
08:49 - Setting HV to 100.0 V
08:49 - Check of HVPA failed: expected 100.00, read 1099.98
08:49 - Check of HVPA failed: expected 100.00, read 1099.98
08:49 - Check of HVPA failed: expected 100.00, read 1099.98
08:49 - Check of HVPA failed: expected 100.00, read 1051.14
08:49 - Check of HVPA failed: expected 100.00, read 1122.91
08:49 - Check of HVPA failed: expected 100.00, read 1122.91
08:49 - Check of HVPA failed: expected 100.00, read 1166.58
08:49 - Check of HVPA failed: expected 100.00, read 1183.17
08:49 - Checking status of HVPA channels in 11 drawer(s)...
08:49 - HVPA channel 0 of drawer 149 has status 0x8001!
08:49 - Resetting HVPA channel 0 of drawer 149...
08:49 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 76 channel(s)
08:49 - Setting HV to nominal values...
08:49 - Setting channel 0 voltages to [1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0]
08:49 - Setting channel 1 voltages to [1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0]
08:49 - Setting channel 2 voltages to [1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0]
08:49 - Setting channel 3 voltages to [1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0]
08:49 - Setting channel 4 voltages to [1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0]
08:49 - Setting channel 5 voltages to [1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0]
08:49 - Setting channel 6 voltages to [1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0, 1000.0]
08:49 - Checking status of HVPA channels in 11 drawer(s)...
08:49 - HVPA channel 0 of drawer 149 has status 0x8001!
08:49 - Resetting HVPA channel 0 of drawer 149...
08:49 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 69 channel(s)
08:49 - Check of 'NectarFrontEnd_115.Hvpa.Hvpa3.Voltage' failed: expected 1000, read 100
08:49 - Check of 'NectarFrontEnd_132.Hvpa.Hvpa5.Voltage' failed: expected 1000, read 100
08:50 - Finished task "Enable HV"
08:50 - Resetting NMC
08:50 - Starting task "Configure NMC"
08:50 - Configuring modules with configuration /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
08:50 - NMC is in state NmcState.Configured and knows of 11 drawer(s)
08:50 - Found 0 PPS errors.
08:50 - Finished task "Configure NMC"
08:50 - Checking high voltages...
08:50 - Starting task "Check HV"
08:50 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
08:50 - Reference voltage of channel 1 in drawer #115: expected 1164.29, read 1000.00
08:50 - Reference voltage of channel 2 in drawer #115: expected 1158.46, read 1000.00
08:50 - Reference voltage of channel 3 in drawer #115: expected 1122.91, read 1126.46
08:50 - Reference voltage of channel 0 in drawer #116: expected 1080.51, read 1000.00
08:50 - Reference voltage of channel 1 in drawer #116: expected 1101.55, read 1000.00
08:50 - Reference voltage of channel 3 in drawer #116: expected 1142.21, read 1000.00
08:50 - Reference voltage of channel 4 in drawer #116: expected 1181.90, read 1000.00
08:50 - Reference voltage of channel 5 in drawer #116: expected 1193.30, read 1000.00
08:50 - Reference voltage of channel 0 in drawer #135: expected 1056.17, read 1000.00
08:50 - Reference voltage of channel 1 in drawer #135: expected 1156.76, read 1000.00
08:50 - Reference voltage of channel 2 in drawer #135: expected 1103.90, read 1000.00
08:50 - Reference voltage of channel 3 in drawer #135: expected 1199.36, read 1103.90
08:50 - Reference voltage of channel 4 in drawer #135: expected 1131.12, read 1000.00
08:50 - Reference voltage of channel 5 in drawer #135: expected 1169.80, read 1000.00
08:50 - Done
08:50 - Found 11 drawer(s). Reference voltage is between 0.00 V and 1223.41 V. Actual voltage is between 0.00 V and 1223.66 V.
08:50 - Maximum difference between reference and actual voltage is 58.35 V
08:50 - Checking status of HVPA module in 11 drawer(s)...
08:50 - HVPA module in drawer 149 has a status of 0x7e!
08:50 - Checking status of HVPA channels in 11 drawer(s)...
08:50 - HVPA channel 0 of drawer 149 has status 0x8001!
08:50 - Resetting HVPA channel 0 of drawer 149...
08:50 - HV was locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 4 channel(s)
08:50 - Finished task "Check HV"
08:50 - Starting task "Configure NMC"
08:50 - Configuring modules with configuration /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
08:50 - NMC is in state NmcState.Configured and knows of 11 drawer(s)
08:50 - Found 0 PPS errors.
08:50 - Finished task "Configure NMC"
08:50 - Checking high voltages...
08:50 - Starting task "Check HV"
08:50 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
08:50 - Reference voltage of channel 4 in drawer #132: expected 1116.44, read 1119.32
08:50 - Done
08:51 - Found 11 drawer(s). Reference voltage is between 0.00 V and 1223.41 V. Actual voltage is between 0.00 V and 1224.27 V.
08:51 - Maximum difference between reference and actual voltage is 3.22 V
08:51 - Checking status of HVPA module in 11 drawer(s)...
08:51 - Checking status of HVPA channels in 11 drawer(s)...
08:51 - HV is stabilized in all channels.
08:51 - Finished task "Check HV"
08:51 - Checking high voltages...
08:51 - Starting task "Check HV"
08:51 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
08:51 - Done
08:51 - Found 11 drawer(s). Reference voltage is between 0.00 V and 1223.41 V. Actual voltage is between 0.00 V and 1223.66 V.
08:51 - Maximum difference between reference and actual voltage is 3.22 V
08:51 - Checking status of HVPA module in 11 drawer(s)...
08:51 - Checking status of HVPA channels in 11 drawer(s)...
08:51 - HV is stabilized in all channels.
08:51 - Finished task "Check HV"
08:53 - Checking high voltages...
08:53 - Starting task "Check HV"
08:53 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
08:53 - Done
08:53 - Found 11 drawer(s). Reference voltage is between 0.00 V and 1223.41 V. Actual voltage is between 0.00 V and 1223.66 V.
08:53 - Maximum difference between reference and actual voltage is 2.59 V
08:53 - Checking status of HVPA module in 11 drawer(s)...
08:53 - Checking status of HVPA channels in 11 drawer(s)...
08:53 - HV is stabilized in all channels.
08:53 - Finished task "Check HV"
08:53 - Starting NMC
08:53 - Clearing PPS error counters
09:01 - Configuring TIB...
09:01 - Setting TIB forced mode to False
09:01 - Writing False to serveur.TIB.Forced.ForcedMode.ForcedMode_v
09:01 - Status: TibState.PpsStopped
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Writing 0.0 to serveur.TIB.ExternalDelay.ExternalDelay_v
09:01 - Setting TIB trigger mode to 0x8 = TriggerMask.SPhE
09:01 - Writing 8 to serveur.TIB.TriggerMode.ModeMask.ModeMask_v
09:01 - Writing 0 to serveur.TIB.InputsEnable.InputMask.InputMask_v
09:01 - Writing False to serveur.TIB.BUSY.DisableBusy.DisableBusy_v
09:01 - Writing 0.0 to serveur.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
09:01 - Writing False to serveur.TIB.Throttler.DisableThrottlerBP.DisableThrottlerBP_v
09:01 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP50us.MaxTriggersBP50us_v
09:01 - Writing 255 to serveur.TIB.Throttler.MaxTriggersBP1ms.MaxTriggersBP1ms_v
09:01 - Writing False to serveur.TIB.Throttler.DisableThrottlerWR.DisableThrottlerWR_v
09:01 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR50us.MaxTriggersWR50us_v
09:01 - Writing 255 to serveur.TIB.Throttler.MaxTriggersWR1ms.MaxTriggersWR1ms_v
09:01 - Status: TibState.PpsStopped
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Closing TIB connection to camera server
09:01 - Connecting TIB to camera server at 10.10.0.251:222
09:01 - Starting TIB...
09:01 - Status: TibState.PpsStopped
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Resetting run
09:01 - Wait for UCTS external trigger before enabling trigger...
09:01 - Status: TibState.Standby
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Status: TibState.Standby
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Status: TibState.Armed
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Starting TIB triggers...
09:01 - Enabling trigger
09:01 - Status: TibState.Running
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Configuring calibration box...
09:01 - Configuring calibration box with leds=0x358 voltage=9.75 frequency=5000.0/1 central_current=0.0 duration=100 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
09:01 - Starting flashes...
09:01 - Stopping TIB...
09:01 - Status: TibState.Running
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Disabling trigger
09:01 - Disabling PPS
09:01 - Status: TibState.PpsStopped
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Closing TIB connection to camera server
09:01 - Status: TibState.PpsStopped
09:01 - Alarms: AlarmVector.NoAlarm
09:01 - Run duration: 0:00:24
09:01 - Local camera triggers: 0
09:01 - Slow control triggers: 0
09:01 - Single photo-electron triggers: 49772
09:01 - Calibration triggers: 0
09:01 - Software triggers from UCTS: 0
09:01 - Auto-pedestal triggers: 151364
09:01 - Collected input triggers: 49772
09:01 - Busy triggers: 0
09:01 - Non-busy triggers sent to UCTS: 49772
09:01 - Camera event triggers sent to clusters: 49772
09:01 - Stopping NMC
09:01 - Found 0 PPS errors.
09:01 - Checking high voltages...
09:01 - Starting task "Check HV"
09:01 - Checking reference voltages against /local/home/cta_test_bench/tests/2018/20180523/NectarCAM.Run0827.NMC.xml
09:01 - Done
09:01 - Found 11 drawer(s). Reference voltage is between 0.00 V and 1223.41 V. Actual voltage is between 0.00 V and 1223.66 V.
09:01 - Maximum difference between reference and actual voltage is 1.98 V
09:01 - Checking status of HVPA module in 11 drawer(s)...
09:01 - Checking status of HVPA channels in 11 drawer(s)...
09:01 - HV is stabilized in all channels.
09:01 - Finished task "Check HV"